fc-magnetite: doc/Config-vars annotate

annotate doc/Config-vars @ 680:ee3ac8c617cb

armio.c: set GPIO2 output high initially On TI-canonical platforms GPIO2 is DCD modem control output. In TI's original code the AI_InitIOConfig() function called from Init_Target() would configure GPIO2 as an output and set the initial output value to low, but then the init code in uartfax.c called from Init_Serial_Flows() would immediately change it to high, corresponding to DCD not asserted. The result is a momentary asserted-state glitch on the DCD output. The present change eliminates this glitch, setting DCD output to not-asserted initially like it should be.

author	Mychaela Falconia <falcon@freecalypso.org>
date	Thu, 25 Jun 2020 03:17:43 +0000
parents	29c0be5a1962
children	b7b809c62586

rev	line source
523 569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	1 The following Bourne shell variables can be set on the ./configure.sh command
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	2 line to tweak the firmware build configuration:
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	3
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	4 ALLOW_CSIM_GSM
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	5
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	6 Per TI's original design, the AT+CSIM command does not allow GSM APDUs
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	7 of class 0xA0. Openmoko found some need for them, and they patched
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	8 their modem fw to allow these APDUs with AT+CSIM. With our new hybrid
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	9 modem fw this policy setting is configurable at build time; the default
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	10 is ALLOW_CSIM_GSM=1 (GSM APDUs allowed).
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	11
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	12 DISABLE_SLEEP
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	13
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	14 The general default is DISABLE_SLEEP=0, and the firmware automatically
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	15 enables all of the chipset's available sleep modes on boot. Setting
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	16 DISABLE_SLEEP=1 causes all sleep modes to be disabled by default on
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	17 boot (they can still be enabled with the AT%SLEEP command); this
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	18 setting is needed for FCDEV3B V1 boards that have a hardware bug that
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	19 causes breakage when sleep modes are enabled.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	20
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	21 DSAMPLE_FULL_COLOR
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	22
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	23 When the firmware's R2D component (normally present only in UI-enabled
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	24 builds) is built for any target other than c139, one of TI's D-Sample
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	25 framebuffer drivers is enabled: either color or B&W. (The actual
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	26 hardware pokes are omitted when the build target is anything other than
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	27 dsample, but the framebuffer is still maintained in RAM.) By default
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	28 the color framebuffer driver is enabled; setting DSAMPLE_FULL_COLOR=0
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	29 switches to the B&W framebuffer driver.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	30
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	31 L1_DYN_DSP_DWNLD
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	32
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	33 This setting enables TI's dynamic DSP patch download mechanism. When
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	34 the firmware is built for a Calypso target with DSP ROM version 36 in
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	35 the silicon (all FreeCalypso-made hw and most of the supported legacy
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	36 targets), L1_DYN_DSP_DWNLD is enabled by default and needs to be kept
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	37 enabled for correct operation: the patch code we got from TI for this
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	38 ROM is the dynamic download version, and the ARM-side L1 code expects
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	39 all of these patches to be present, both the static part and the
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	40 dynamic parts. However, one can build our fw with L1_DYN_DSP_DWNLD=0
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	41 for experimental testing, to see what breaks when the dynamic patches
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	42 are omitted.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	43
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	44 L1_VOICE_MEMO_AMR
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	45
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	46 This setting enables or disables support in L1 and in the RiViera Audio
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	47 Service for AMR voice memo recording and playback. This code has not
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	48 been properly studied yet and no test AT commands are provided for it,
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	49 but it is enabled by default like in TI's original TCS211 fw.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	50
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	51 MELODY_E2
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	52
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	53 This setting enables or disables support in L1 and in the RiViera Audio
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	54 Service for playing E2-format melodies. The default is MELODY_E2=1
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	55 like in TI's original TCS211 fw. Note that Melody E1 support is always
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	56 enabled; setting MELODY_E2=0 disables only Melody E2, but not E1.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	57
541 5019764a0e9f doc/Config-vars: RVTMUX_ON_MODEM documented Mychaela Falconia <falcon@freecalypso.org> parents: 523 diff changeset	58 RVTMUX_ON_MODEM
5019764a0e9f doc/Config-vars: RVTMUX_ON_MODEM documented Mychaela Falconia <falcon@freecalypso.org> parents: 523 diff changeset	59
5019764a0e9f doc/Config-vars: RVTMUX_ON_MODEM documented Mychaela Falconia <falcon@freecalypso.org> parents: 523 diff changeset	60 This setting configures the usage of Calypso UARTs. RVTMUX_ON_MODEM=0
5019764a0e9f doc/Config-vars: RVTMUX_ON_MODEM documented Mychaela Falconia <falcon@freecalypso.org> parents: 523 diff changeset	61 puts the AT command interface on the MODEM UART and RVTMUX on the IrDA
5019764a0e9f doc/Config-vars: RVTMUX_ON_MODEM documented Mychaela Falconia <falcon@freecalypso.org> parents: 523 diff changeset	62 UART (TI's intended config and the default on sensible hw targets);
5019764a0e9f doc/Config-vars: RVTMUX_ON_MODEM documented Mychaela Falconia <falcon@freecalypso.org> parents: 523 diff changeset	63 RVTMUX_ON_MODEM=1 (default on the crippled C1xx targets) puts RVTMUX on
5019764a0e9f doc/Config-vars: RVTMUX_ON_MODEM documented Mychaela Falconia <falcon@freecalypso.org> parents: 523 diff changeset	64 the MODEM UART, sacrificing the standard AT command interface.
5019764a0e9f doc/Config-vars: RVTMUX_ON_MODEM documented Mychaela Falconia <falcon@freecalypso.org> parents: 523 diff changeset	65
523 569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	66 SERIAL_DYNAMIC_SWITCH
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	67
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	68 TI's TCS211 fw includes a provision (only for Bluetooth-enabled fw in
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	69 TI's original) to switch one UART between the AT command interface and
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	70 RVTMUX while the other UART is fixed for Bluetooth. In FreeCalypso we
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	71 have changed this code to work without Bluetooth, for the purpose of
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	72 switching the user-facing MODEM UART between AT commands and RVTMUX,
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	73 but the mechanism does not work properly yet and is disabled by default.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	74 Enable it with SERIAL_DYNAMIC_SWITCH=1 if you would like to play with
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	75 it.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	76
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	77 SPEECH_RECO
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	78
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	79 This setting enables or disables support in L1 and in the RiViera Audio
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	80 Service for TI's speech recognition mechanism. This code and the
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	81 underlying DSP facility itself have not been properly studied yet and
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	82 no test AT commands are provided for it, but it is enabled by default
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	83 like in TI's original TCS211 fw.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	84
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	85 SUFFIX
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	86
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	87 This setting is solely for configuration management. If you make a
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	88 build with any of the settings described in this document changed from
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	89 the default, you should also pass a SUFFIX=-xxx argument so your special
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	90 build will be appropriately identified in the build directory name and
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	91 in the firmware version ID string compiled into the image. The naming
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	92 of suffixes is up to you, but here are some examples:
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	93
569 29c0be5a1962 doc update for the arrival of correctly working FCDEV3B V2 hardware Mychaela Falconia <falcon@freecalypso.org> parents: 550 diff changeset	94 DISABLE_SLEEP=1 SUFFIX=-nosleep
523 569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	95 DSAMPLE_FULL_COLOR=0 UI_CONFIG=bigbw SUFFIX=-bw
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	96 L1_DYN_DSP_DWNLD=0 SUFFIX=-nodyn
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	97 MELODY_E2=0 SUFFIX=-noe2
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	98 SERIAL_DYNAMIC_SWITCH=1 SUFFIX=-sds
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	99 SPEECH_RECO=0 SUFFIX=-nosr
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	100 TR_BAUD_CONFIG=TR_BAUD_812500 SUFFIX=-812500
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	101 USE_STR2IND=1 SUFFIX=-s2i
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	102
550 a1da09e02973 doc/Config-vars: TRACEMASK_IN_FFS addition documented Mychaela Falconia <falcon@freecalypso.org> parents: 541 diff changeset	103 TRACEMASK_IN_FFS
a1da09e02973 doc/Config-vars: TRACEMASK_IN_FFS addition documented Mychaela Falconia <falcon@freecalypso.org> parents: 541 diff changeset	104
a1da09e02973 doc/Config-vars: TRACEMASK_IN_FFS addition documented Mychaela Falconia <falcon@freecalypso.org> parents: 541 diff changeset	105 TI's Test Interface (TIF) component in the GPF realm includes an
a1da09e02973 doc/Config-vars: TRACEMASK_IN_FFS addition documented Mychaela Falconia <falcon@freecalypso.org> parents: 541 diff changeset	106 optional feature for saving trace masks in FFS, but TI's production
a1da09e02973 doc/Config-vars: TRACEMASK_IN_FFS addition documented Mychaela Falconia <falcon@freecalypso.org> parents: 541 diff changeset	107 firmwares had it disabled. We have now switched to recompiling the
a1da09e02973 doc/Config-vars: TRACEMASK_IN_FFS addition documented Mychaela Falconia <falcon@freecalypso.org> parents: 541 diff changeset	108 component in question from source, but we still keep this
a1da09e02973 doc/Config-vars: TRACEMASK_IN_FFS addition documented Mychaela Falconia <falcon@freecalypso.org> parents: 541 diff changeset	109 TRACEMASK_IN_FFS code disabled by default, at least for now.
a1da09e02973 doc/Config-vars: TRACEMASK_IN_FFS addition documented Mychaela Falconia <falcon@freecalypso.org> parents: 541 diff changeset	110 Set TRACEMASK_IN_FFS=1 to enable this code in GPF.
a1da09e02973 doc/Config-vars: TRACEMASK_IN_FFS addition documented Mychaela Falconia <falcon@freecalypso.org> parents: 541 diff changeset	111
523 569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	112 TR_BAUD_CONFIG
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	113
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	114 The value of this symbol is an alphanumeric keyword of the form
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	115 TR_BAUD_xxxxxx; the default is TR_BAUD_115200. See
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	116 src/cs/drivers/drv_core/uart/traceswitch.h for the available baud rate
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	117 choices; the most practical use is setting TR_BAUD_CONFIG=TR_BAUD_812500
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	118 when you need to run the RVTMUX serial channel at the maximum possible
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	119 baud rate.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	120
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	121 UI_CONFIG
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	122
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	123 The 3 allowed values for this setting are bigcolor, bigbw and 84x48,
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	124 selecting one of the 3 UI configurations supported by TI's code. The
541 5019764a0e9f doc/Config-vars: RVTMUX_ON_MODEM documented Mychaela Falconia <falcon@freecalypso.org> parents: 523 diff changeset	125 default is 84x48 when the firmware is built for target c11x or c139 or
5019764a0e9f doc/Config-vars: RVTMUX_ON_MODEM documented Mychaela Falconia <falcon@freecalypso.org> parents: 523 diff changeset	126 c155, and bigcolor otherwise.
523 569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	127
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	128 USE_STR2IND
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	129
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	130 Unlike TI's original firmwares, we build without str2ind by default.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	131 You can enable str2ind with USE_STR2IND=1, but the time to build the fw
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	132 will be significantly longer as the compiler has to be run twice for
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	133 each C source file, with str2ind sandwiched in between.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	134
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	135 The following Bourne shell variables are used inside the build system in the
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	136 individual component build recipes (components/*) but cannot be set on the
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	137 ./configure.sh line because they are fixed in the overall fw build recipes
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	138 (configs/*):
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	139
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	140 GPRS
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	141
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	142 Self-explanatory: enables or disables GPRS.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	143
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	144 MMI
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	145
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	146 TI's original config variable: MMI=0 for the AT-command-controlled
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	147 modem configuration or MMI=2 for the UI-enabled configuration with
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	148 BMI and MFW.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	149
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	150 SRVC
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	151
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	152 TI's original config variable, selects the presence or absence of data
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	153 services other than GPRS as follows:
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	154
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	155 SRVC=0: voice and SMS only
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	156 SRVC=1: CSD and fax enabled
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	157 SRVC=2: CSD enabled, but not fax
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	158
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	159 Finally, CHIPSET, DSP, RF and AMR variables reflect the physical configuration
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	160 of the selected target hw that no amount of software hacking can change.
569c3d522e5c doc/Config-vars: written Mychaela Falconia <falcon@freecalypso.org> parents: diff changeset	161 (The AMR variable indicates the presence or absence of AMR support in the DSP.)

FreeCalypso > hg > fc-magnetite

annotate doc/Config-vars @ 680:ee3ac8c617cb