--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/src/cs/drivers/drv_core/ulpd/ulpd.h	Sun Sep 25 22:50:11 2016 +0000
@@ -0,0 +1,262 @@
+/*******************************************************************************
+            TEXAS INSTRUMENTS INCORPORATED PROPRIETARY INFORMATION           
+                                                                             
+  Property of Texas Instruments -- For  Unrestricted  Internal  Use  Only 
+   Unauthorized reproduction and/or distribution is strictly prohibited.  This 
+   product  is  protected  under  copyright  law  and  trade  secret law as an 
+   unpublished work.  Created 1987, (C) Copyright 1997 Texas Instruments.  All 
+   rights reserved.                                                            
+                 
+                                                           
+   Filename       	: ulpd.h
+
+   Description    	: Header for HYPERION/ULPD module tests
+			  Target : Arm
+
+   Project        	: Hyperion
+
+   Author         	: smunsch@tif.ti.com  Sylvain Munsch.
+
+   Version number	: 1.11
+
+   Date and time	: 12/20/00 10:17:22
+
+   Previous delta 	: 12/06/00 17:31:50
+
+   SCCS file      	: /db/gsm_asp/db_ht96/dsp_0/gsw/rel_0/mcu_l1/release_gprs/mod/emu_p/EMU_P/drivers1/common/SCCS/s.ulpd.h
+
+   Sccs Id  (SID)       : '@(#) ulpd.h 1.11 12/20/00 10:17:22 '
+
+ 
+*****************************************************************************/
+
+#ifndef _WINDOWS
+   #include "chipset.cfg"
+   #include "board.cfg"
+   #include "rf.cfg"
+#endif
+
+#include <limits.h>
+#include <float.h>
+
+// SLEEP MODES
+//=======================
+#define DO_NOT_SLEEP          00
+#define FRAME_STOP            01 // little BIG SLEEP (CUST5...)
+#define CLOCK_STOP            02 // Deep sleep
+
+
+// ULPD registers address 
+//=======================
+
+#define ULPD_XIO_START               0xfffe2000
+
+#define ULPD_INC_FRAC_REG             (SYS_UWORD16 *)(ULPD_XIO_START)	
+#define ULDP_INC_SIXTEENTH_REG       ((SYS_UWORD16 *)(ULPD_XIO_START) + 1)
+#define ULDP_SIXTEENTH_START_REG     ((SYS_UWORD16 *)(ULPD_XIO_START) + 2)
+#define ULDP_SIXTEENTH_STOP_REG	     ((SYS_UWORD16 *)(ULPD_XIO_START) + 3)
+#define ULDP_COUNTER_32_LSB_REG	     ((SYS_UWORD16 *)(ULPD_XIO_START) + 4)
+#define ULDP_COUNTER_32_MSB_REG	     ((SYS_UWORD16 *)(ULPD_XIO_START) + 5)
+#define ULDP_COUNTER_HI_FREQ_LSB_REG ((SYS_UWORD16 *)(ULPD_XIO_START) + 6)
+#define ULDP_COUNTER_HI_FREQ_MSB_REG ((SYS_UWORD16 *)(ULPD_XIO_START) + 7)
+#define ULDP_GAUGING_CTRL_REG        ((SYS_UWORD16 *)(ULPD_XIO_START) + 8)
+#define ULDP_GAUGING_STATUS_REG      ((SYS_UWORD16 *)(ULPD_XIO_START) + 9)
+#define ULDP_GSM_TIMER_CTRL_REG      ((SYS_UWORD16 *)(ULPD_XIO_START) + 10)  
+#define ULDP_GSM_TIMER_INIT_REG      ((SYS_UWORD16 *)(ULPD_XIO_START) + 11)
+#define ULDP_GSM_TIMER_VALUE_REG     ((SYS_UWORD16 *)(ULPD_XIO_START) + 12)
+#define ULDP_GSM_TIMER_IT_REG        ((SYS_UWORD16 *)(ULPD_XIO_START) + 13) 
+#define ULDP_SETUP_CLK13_REG   	     ((SYS_UWORD16 *)(ULPD_XIO_START) + 14)
+#define ULDP_SETUP_SLICER_REG	     ((SYS_UWORD16 *)(ULPD_XIO_START) + 15)
+#define ULDP_SETUP_VTCXO_REG         ((SYS_UWORD16 *)(ULPD_XIO_START) + 16) 
+#define ULDP_SETUP_FRAME_REG         ((SYS_UWORD16 *)(ULPD_XIO_START) + 17) 
+#define ULPD_SETUP_RF_REG            ((SYS_UWORD16 *)(ULPD_XIO_START) + 18)
+
+
+// ULPD gauging control register description 
+//==========================================
+
+#define ULDP_GAUGING_EN	              0x0001   // Gauging is running 
+#define ULDP_GAUGING_TYPE_HF          0x0002   // Gauging versus HFclock
+#define ULDP_SEL_HF_PLL               0x0004   // High freq clock = PLL DSP 
+
+// ULPD gauging status register description 
+//==========================================
+
+#define ULDP_IT_GAUGING               0x0001  // Interrupt it_gauging occurence 
+#define ULDP_OVF_HF                   0x0002  // Overflow on the HF counter 
+#define ULDP_OVF_32                   0x0004  // Overflow on the 32 Khz counter
+
+// WAKEup time
+//==========================================
+//  the setup time unit is the number of 32 Khz clock periods
+
+#if (BOARD == 34)
+
+#define SETUP_RF                      75      // adujstement time to minimize big_sleep duration
+                                              // The SETUP_RF value must be used to delay as much as possible the true  
+                                              // start time of the deep_sleep wake-up sequence for power consumption saving. 
+                                              // This is required because the unit of the SETUP_FRAME counter is the  
+                                              // GSM TDMA frame and not a T32K time period.
+
+#define SETUP_VTCXO                   320     // The setup_vtcxo is the time the external RF device takes to deliver
+                                              // stable signals to the VTCXO
+
+
+#define SETUP_SLICER                  180     // The setup_slicer is the time that the vtcxo takes to deliver 
+                                              // a stable output when vtcxo is enabled : usually 2 to 5ms
+                                              // The SETUP_SLICER value should be smaller than 160(=4,8ms) but this 
+                                              // parameter is directly related to the VTCXO device used in the phone
+                                              // and consequently must be retrieved from the VTCXO data-sheet.
+
+#define SETUP_CLK13                   31      // The setup_clk13 is time that the slicer takes to deliver
+                                              // a stable output when slicer is enabled : max conservative value 1ms
+
+#else
+
+#define SETUP_RF                      0       // adujstement time to minimize big_sleep duration
+                                              // The SETUP_RF value must be used to delay as much as possible the true  
+                                              // start time of the deep_sleep wake-up sequence for power consumption saving. 
+                                              // This is required because the unit of the SETUP_FRAME counter is the  
+                                              // GSM TDMA frame and not a T32K time period.
+#if (CHIPSET == 2)
+  #define SETUP_VTCXO                 31      // The setup_vtcxo is the time the external RF device takes to deliver
+#else                                         // stable signals to the VTCXO
+  #define SETUP_VTCXO                 1114    // 34 ms for ABB LDO stabilization before 13MHz switch ON
+                                              // Minimum value to be sure that ABB is awake while the DBB start running for 
+                                              // SETUP_VTCXO  =  ((SLPDLY*16)+4+145)*T32KHz       
+#endif  
+
+#if (BOARD == 40) || (BOARD == 41) || (BOARD == 42) || (BOARD == 43) || (BOARD == 45)
+  #if (RF_FAM==12)
+    #define SETUP_SLICER                660
+  #else 
+    #define SETUP_SLICER                600     // 600/32x10^3 = 18.75ms required for VCXO stabilization
+  #endif
+#else
+  #define SETUP_SLICER                180     // The setup_slicer is the time that the vtcxo takes to deliver 
+                                              // a stable output when vtcxo is enabled : usually 2 to 5ms
+                                              // The SETUP_SLICER value should be smaller than 160(=4,8ms) but this 
+                                              // parameter is directly related to the VTCXO device used in the phone
+                                              // and consequently must be retrieved from the VTCXO data-sheet.
+#endif
+
+#define SETUP_CLK13                   31      // The setup_clk13 is time that the slicer takes to deliver
+                                              // a stable output when slicer is enabled : max conservative value 1ms
+
+#endif // BOARD == 34
+
+// SETUP_FRAME:
+//-------------
+// CF. Reference document: ULYS015 v1.1 page 24
+// 1) Nominal Frequency = 32.768 Khz => 0.03051757 ms 
+//    (0.03051757 ms / 4.615 ms) =  0.006612692 Frames 
+// 2) The use of the RFEN signal is optional. It is necessary if the VTCXO function 
+//    is part of an RF IC which must be first powered before enabling the VTCXO. 
+//    However it can be use for any other purpose.
+// 3) The term (1-DBL_EPSILON) corresponds to the rounding up of SETUP_FRAME.
+#ifndef DBL_EPSILON  //CQ16723: For non TI compiler, DBL_EPSILON can be undefined.
+ #define DBL_EPSILON 0
+#endif
+
+#define SETUP_FRAME  ((( SETUP_RF+SETUP_VTCXO+SETUP_SLICER+SETUP_CLK13)*0.006612692)+(1-DBL_EPSILON))
+
+#define MAX_GSM_TIMER                 65535   // max duration for the wake up timer
+
+
+// Default values for Cell selection and CS_MODE0
+//===============================================
+#define DEFAULT_HFMHZ_VALUE (13000000*l1_config.dpll)
+#define DEFAULT_32KHZ_VALUE (32768)   // real value 32768.29038 hz
+//with l1ctl_pgm_clk32(DEFAULT_HFMHZ_VALUE,DEFAULT_32KHZ_VALUE) and dpll = 65Mhz
+//          => DEFAULT_INCSIXTEEN           132
+//          => DEFAULT_INCFRAC              15915 
+
+
+
+
+
+// ULPD GSM timer control register description 
+//============================================
+
+#define ULDP_TM_LOAD                  0x0001 // load the timer with init value 
+#define ULDP_TM_FREEZE                0x0002 // 1=> GSM timer is frozen 
+#define ULPD_IT_TIMER_GSM             0x0001 // Interrupt timer occurrence 	
+
+
+//  ULDP_INCFRAC_UPDATE : update INCFRAC (16 bits)
+//================================================
+#define ULDP_INCFRAC_UPDATE(frac)  (* (volatile SYS_UWORD16 *)ULPD_INC_FRAC_REG = frac)
+
+
+//  ULDP_INCSIXTEEN_UPDATE : update INCSIXTEEN (12 bits)
+//======================================================
+#define ULDP_INCSIXTEEN_UPDATE(inc)  (* (volatile SYS_UWORD16 *)ULDP_INC_SIXTEENTH_REG = inc)
+
+
+// ULDP_GAUGING_RUN : Start the gauging 
+//=====================================
+#define ULDP_GAUGING_RUN  (* (volatile SYS_UWORD16 *)ULDP_GAUGING_CTRL_REG |= ULDP_GAUGING_EN)
+
+
+// ULDP_GAUGING_STATUS : Return if it gauging occurence
+//======================================================
+#define ULDP_GAUGING_STATUS ((* (volatile SYS_UWORD16 *) ULDP_GAUGING_STATUS_REG) & ULDP_GAUGING_EN )
+
+// ULDP_GAUGING_STOP : Stop the gauging  
+//=====================================
+#define ULDP_GAUGING_STOP (* (volatile SYS_UWORD16 *) ULDP_GAUGING_CTRL_REG &= ~ULDP_GAUGING_EN) 
+
+// ULDP_GAUGING_START : Stop the gauging  
+//=====================================
+#define ULDP_GAUGING_START (* (volatile SYS_UWORD16 *) ULDP_GAUGING_CTRL_REG |= ULDP_GAUGING_EN) 
+
+// ULDP_GAUGING_SET_HF : Set the gauging versus HF clock
+//======================================================
+#define ULDP_GAUGING_SET_HF (* (volatile SYS_UWORD16 *) ULDP_GAUGING_CTRL_REG |= ULDP_GAUGING_TYPE_HF)
+
+//  ULDP_GAUGING_HF_PLL : Set the gauging HF versus PLL clock
+//===========================================================
+#define ULDP_GAUGING_HF_PLL (* (volatile SYS_UWORD16 *) ULDP_GAUGING_CTRL_REG |= ULDP_SEL_HF_PLL)
+
+
+//  ULDP_GET_IT_GAG : Return if the interrupt it gauging occurence
+//================================================================
+#define ULDP_GET_IT_GAG ((* (volatile SYS_UWORD16 *) ULDP_GAUGING_STATUS_REG) & ULDP_IT_GAUGING )
+
+//  ULDP_GET_OVF_HF : Return overflow occured on the HF counter  
+//=============================================================
+#define ULDP_GET_OVF_HF (((* (volatile SYS_UWORD16 *) ULDP_GAUGING_STATUS_REG) & ULDP_OVF_HF)>>1)
+
+//  ULDP_GET_OVF_32 : Return overflow occured on the 32 counter  
+//=============================================================
+#define ULDP_GET_OVF_32 (((* (volatile SYS_UWORD16 *) ULDP_GAUGING_STATUS_REG) & ULDP_OVF_32)>>2)
+
+//  ULDP_TIMER_INIT : Load the  timer_init value
+//=========================================================
+#define ULDP_TIMER_INIT(value) ((* (volatile SYS_UWORD16 *)ULDP_GSM_TIMER_INIT_REG) = value)
+
+//  READ_ULDP_TIMER_INIT : Read the  timer_init value
+//=========================================================
+#define READ_ULDP_TIMER_INIT (* (volatile SYS_UWORD16 *)ULDP_GSM_TIMER_INIT_REG)
+
+//  READ_ULDP_TIMER_VALUE : Read the  timer_init value
+//=========================================================
+#define READ_ULDP_TIMER_VALUE (* (volatile SYS_UWORD16 *)ULDP_GSM_TIMER_VALUE_REG)
+
+//  ULDP_TIMER_LD : Load the timer with timer_init value
+//=========================================================
+#define ULDP_TIMER_LD ((* (volatile SYS_UWORD16 *)ULDP_GSM_TIMER_CTRL_REG) |= ULDP_TM_LOAD)
+
+//  ULDP_TIMER_FREEZE : Freeze the timer 
+//=========================================================
+#define ULDP_TIMER_FREEZE ((* (volatile SYS_UWORD16 *)ULDP_GSM_TIMER_CTRL_REG) |= ULDP_TM_FREEZE)
+
+//  ULDP_GSM_TIME_START : Run the GSM timer
+//=========================================
+#define ULDP_TIMER_START ((* (volatile SYS_UWORD16 *)ULDP_GSM_TIMER_CTRL_REG) &= ~ULDP_TM_FREEZE)
+
+//  ULDP_GET_IT_TIMER : Return the it GSM timer occurence
+//===========================================================
+#define ULDP_GET_IT_TIMER ((* (volatile SYS_UWORD16 *) ULDP_GSM_TIMER_IT_REG) & ULPD_IT_TIMER_GSM )
+
+