/************* Revision Controle System Header *************
 *                  GSM Layer 1 software
 *
 *        Filename l1_rf12.h
 *  Copyright 2003 (C) Texas Instruments  
 * 
 ************* Revision Controle System Header *************/

#ifndef __L1_RF_H__
#define __L1_RF_H__

#include "fc-target.h"

#define RF_RITA_10 0x2030 // Check with TIDK

//#define RF_HW_BAND_EGSM
//#define RF_HW_BAND_DCS
#define RF_HW_BAND_PCS 0x4
#define RF_HW_BAND_DUAL_US  0x80
#define RF_HW_BAND_DUAL_EXT 0x20

//#define RF_HW_BAND_SUPPORT (0x0020 | RF_HW_BAND_PCS)  // radio_band_support E-GSM/DCS + PCS
// radio_band_support E-GSM/DCS + GSM850/PCS
#define RF_HW_BAND_SUPPORT (RF_HW_BAND_DUAL_EXT | RF_HW_BAND_DUAL_US)

// L1 RF SW Multiband configuration
//--------------------------

// RF_SW_MULTIBAND_SUPPORT values
#define SINGLE_BAND_900                 1
#define SINGLE_BAND_1800                2
#define SINGLE_BAND_850                 3
#define SINGLE_BAND_1900                4
#define DUAL_BAND_900_1800              5
#define DUAL_BAND_850_1900              6
#define TRI_BAND_900_1800_1900          7
#define TRI_BAND_850_1900_1800          8
#define QUAD_BAND                       9

//IMPORTANT  !: To change RF_SW_MULTIBAND_SUPPORT value, it must be synchronized with other multiband settings in the software
// To match the protocol stack settings( e.g EF_RFCAP ) in order to make sure that the value of STD sent in MPHC_INIT_L1_REQ is supported by L1
// And also match the RF HW support: RF_HW_BAND_SUPPORT
#define   RF_SW_MULTIBAND_SUPPORT   QUAD_BAND  

 // Generate band dependancy options
#define RF_SW_BAND900   ((RF_SW_MULTIBAND_SUPPORT == SINGLE_BAND_900)||(RF_SW_MULTIBAND_SUPPORT == DUAL_BAND_900_1800) \
    					||(RF_SW_MULTIBAND_SUPPORT == TRI_BAND_900_1800_1900) ||(RF_SW_MULTIBAND_SUPPORT == QUAD_BAND) )

 #define RF_SW_BAND1800  ((RF_SW_MULTIBAND_SUPPORT == SINGLE_BAND_1800) ||(RF_SW_MULTIBAND_SUPPORT == DUAL_BAND_900_1800) \
    					 ||(RF_SW_MULTIBAND_SUPPORT == TRI_BAND_900_1800_1900) ||(RF_SW_MULTIBAND_SUPPORT == TRI_BAND_850_1900_1800) \
    					 ||(RF_SW_MULTIBAND_SUPPORT == QUAD_BAND))

 #define RF_SW_BAND850    ((RF_SW_MULTIBAND_SUPPORT == SINGLE_BAND_850)||(RF_SW_MULTIBAND_SUPPORT == DUAL_BAND_850_1900) \
    					 ||(RF_SW_MULTIBAND_SUPPORT == TRI_BAND_850_1900_1800) ||(RF_SW_MULTIBAND_SUPPORT == QUAD_BAND)) 

 #define RF_SW_BAND1900  ((RF_SW_MULTIBAND_SUPPORT == SINGLE_BAND_1900)||(RF_SW_MULTIBAND_SUPPORT == DUAL_BAND_850_1900) \
 					 ||(RF_SW_MULTIBAND_SUPPORT == TRI_BAND_900_1800_1900)||(RF_SW_MULTIBAND_SUPPORT == TRI_BAND_850_1900_1800) \
 					||(RF_SW_MULTIBAND_SUPPORT == QUAD_BAND))

/************************************/
/* SYNTHESIZER setup time...        */
/************************************/
#define RX_SYNTH_SETUP_TIME (PROVISION_TIME - TRF_R1)//RX Synthesizer setup time in qbit.
#define TX_SYNTH_SETUP_TIME (- TRF_T1)               //TX Synthesizer setup time in qbit.

/************************************/
/* time for TPU scenario ending...  */
/************************************/
//
// The following values are used to take into account any TPU activity AFTER
// BDLON (or BDLENA) down (for RX) and BULON down (for TX)
// - If there are no TPU commands after BDLON (or BDLENA) down and BULON down,
//   these defines must be ZERO
// - If there IS some TPU command after BDLON (or BDLENA) and BULON down,
//   these defines must be equal to the time difference (in qbits) between 
//   the BDLON (or BDLENA) or BULON time and the last TPU command on 
//   the TPU scenario
#define RX_TPU_SCENARIO_ENDING  0   // execution time of AFTER BDLENA down
#define TX_TPU_SCENARIO_ENDING  0   // execution time of AFTER BULON down


/******************************************************/
/* TXPWR configuration...                             */
/* Fixed TXPWR value when GSM management is disabled. */
/******************************************************/

#if ((ANLG_FAM == 1) || (ANLG_FAM == 2) || (ANLG_FAM == 3))
//  #define FIXED_TXPWR       ((0xFC<<6) | AUXAPC | FALSE)  // TXPWR=10, value=252
//#define FIXED_TXPWR         ((0x65<<6) | AUXAPC | FALSE)  
  #define FIXED_TXPWR       ((0x74<<6) | AUXAPC | FALSE)  // TXPWR=15
#endif


/************************************/
/* ANALOG delay (in qbits)          */
/************************************/
#define  DL_DELAY_RF      1   // time spent in the Downlink global RF chain by the modulated signal 
#define  UL_DELAY_1RF     7   // time spent in the first  uplink RF block
#define  UL_DELAY_2RF     0   // time spent in the second uplink RF block
#if (ANLG_FAM == 1)
  #define  UL_ABB_DELAY   3   // modulator input to output delay
#endif
#if ((ANLG_FAM == 2) || (ANLG_FAM == 3))
  #define  UL_ABB_DELAY   3   // modulator input to output delay
#endif

/************************************/
/* TX Propagation delay...          */
/************************************/
 #if ((ANLG_FAM == 1) || (ANLG_FAM == 2) || (ANLG_FAM == 3))
  #define  PRG_TX       (DL_DELAY_RF + UL_DELAY_2RF + (GUARD_BITS*4) + UL_DELAY_1RF + UL_ABB_DELAY)   // = 40
#endif

/************************************/
/* Initial value for APC DELAY      */
/************************************/
#if (ANLG_FAM == 1)
//#define APCDEL_DOWN     (32 - GUARD_BITS*4)          // minimum value: 2
  #define APCDEL_DOWN      2                           // minimum value: 2
  #define APCDEL_UP       (6+5)                        // minimum value: 6
#endif

#if (ANLG_FAM == 2) || (ANLG_FAM == 3)
//#define APCDEL_DOWN     (32 - GUARD_BITS*4)          // minimum value: 2
  #define APCDEL_DOWN     (2+0)                        // minimum value: 2
  #define APCDEL_UP       (6+3+1)                      // minimum value: 6
                                                       // REMOVE // Jerome Modif for ARF7: (6+3) instead of (6+8)
#endif

#define GUARD_BITS 7

/************************************/
/* Initial value for AFC...         */
/************************************/
#define  EEPROM_AFC    ((150)*8)      // F13.3 required!!!!! (default : -952*8, initial deviation of -2400 forced)

#define  SETUP_AFC_AND_RF     6       // AFC converges in 2 frames and RF BAND GAP stable after 4 frames
                                      // Rita (RF=12) LDO wakeup requires 6 frames

/************************************/
/* Baseband registers               */
/************************************/
#if (ANLG_FAM == 1)
   // Omega registers values will be programmed at 1st DSP communication interrupt 
  #define  C_DEBUG1           0x0001                            // Enable f_tx delay of 400000 cyc DEBUG 
  #define  C_AFCCTLADD      ((0x000 << 6) | AFCCTLADD | TRUE)   // Value at reset
  #define  C_VBUCTRL        ((0x106 << 6) | VBUCTRL   | TRUE)   // Uplink gain amp 0dB, Sidetone gain to mute
  #define  C_VBDCTRL        ((0x026 << 6) | VBDCTRL   | TRUE)   // Downlink gain amp 0dB, Volume control 0 dB
  // RITA does not need an APCOFFSET because the PACTRL is internal: 
// REMOVE //#define  C_APCOFF          0x1016 | (0x3c << 6) | TRUE   // value at reset-Changed from 0x0016- CR 27.12  
  #define  C_APCOFF         ((0x040 << 6) | APCOFF    | TRUE)
  #define  C_BULIOFF        ((0x0FF << 6) | BULIOFF   | TRUE)   // value at reset
  #define  C_BULQOFF        ((0x0FF << 6) | BULQOFF   | TRUE)   // value at reset
  #define  C_DAI_ON_OFF      (0x000)                            // value at reset
  #define  C_AUXDAC         ((0x000 << 6) | AUXDAC    | TRUE)   // value at reset
  #define  C_VBCTRL         ((0x00B << 6) | VBCTRL    | TRUE)   // VULSWITCH=1, VDLAUX=1, VDLEAR=1 
  // BULRUDEL will be initialized on rach only ....
  #define  C_APCDEL1        (((APCDEL_DOWN-2) << 11)  | ((APCDEL_UP-6) << 6) | APCDEL1) 
  #define  C_BBCTRL         ((0x181 << 6) | BBCTRL    | TRUE)   // OUTLEV1=OUTLEV1=SELVMID1=SELVMID0=1 for B-sample 'modified'
#endif

#if (ANLG_FAM == 2)

  // IOTA registers values will be programmed at 1st DSP communication interrupt

  #define  C_DEBUG1          0x0001          // Enable f_tx delay of 400000 cyc DEBUG 
  #define  C_AFCCTLADD      ((0x000 << 6) | AFCCTLADD | TRUE)   // Value at reset
  #define  C_VBUCTRL        ((0x0C9 << 6) | VBUCTRL   | TRUE)   // Uplink gain amp 3 dB, Sidetone gain to -17dB
  #define  C_VBDCTRL        ((0x006 << 6) | VBDCTRL   | TRUE)   // Downlink gain amp 0dB, Volume control -12 dB
 // RITA does not need an APCOFFSET because the PACTRL is internal: 
  // REMOVE //#define  C_APCOFF          0x1016 | (0x3c << 6) | TRUE   // x2 slope 128 
#if (RF_PA == 0 || RF_PA == 3) || defined(CONFIG_TARGET_PIRELLI)
  #define  C_APCOFF         ((0x040 << 6) | APCOFF    | TRUE) // x2 slope 128
#elif defined(CONFIG_TARGET_C1XX)
  #define  C_APCOFF         ((0x060 << 6) | APCOFF    | TRUE) // x2 slope 128
#elif defined(CONFIG_TARGET_J100)
  #define  C_APCOFF         ((0x074 << 6) | APCOFF    | TRUE) // x2 slope 128
#elif (RF_PA == 1 || RF_PA == 2 || RF_PA == 4)
  #define  C_APCOFF         ((0x070 << 6) | APCOFF    | TRUE) // x2 slope 128
#endif
  #define  C_BULIOFF        ((0x0FF << 6) | BULIOFF   | TRUE)   // value at reset
  #define  C_BULQOFF        ((0x0FF << 6) | BULQOFF   | TRUE)   // value at reset
  #define  C_DAI_ON_OFF     ((0x000 << 6) | APCOFF    | TRUE)   // value at reset
  #define  C_AUXDAC         ((0x000 << 6) | AUXDAC    | TRUE)   // value at reset


// audio patch for H2-sample:
#if (RAZ_VULSWITCH_REGAUDIO == 1)
  #define  C_VBCTRL1        ((0x003 << 6) | VBCTRL1   | TRUE)   // VBDFAUXG = 1, VULSWITCH=0, VDLAUX=1, VDLEAR=1 // jkb h2sample change
#else
  #define  C_VBCTRL1        ((0x00B << 6) | VBCTRL1   | TRUE)   // VULSWITCH=1, VDLAUX=1, VDLEAR=1 
#endif


  #define  C_VBCTRL2        ((0x000 << 6) | VBCTRL2   | TRUE)   // MICBIASEL=0, VDLHSO=0, MICAUX=0
  // BULRUDEL will be initialized on rach only ....
  #define  C_APCDEL1        (((APCDEL_DOWN-2) << 11)  | ((APCDEL_UP-6) << 6) | APCDEL1)  
  #define  C_APCDEL2        ((0x000 << 6) | APCDEL2   | TRUE)                          //
  #define  C_BBCTRL         ((0x2C1 << 6) | BBCTRL    | TRUE)   // Internal autocalibration, Output common mode=1.35V
                                             // Monoslot, Vpp=8/15*Vref                                             
  #define  C_BULGCAL        ((0x000 << 6) | BULGCAL   | TRUE) // IAG=0 dB, QAG=0 dB 
#endif

#if (ANLG_FAM == 3)

  // SYREN registers values will be programmed at 1st DSP communication interrupt

  #define  C_DEBUG1          0x0001                      // Enable f_tx delay of 400000 cyc DEBUG 
  #define  C_AFCCTLADD      ((0x000 << 6) | AFCCTLADD | TRUE)   // Value at reset
  #define  C_VBUCTRL        ((0x0C9 << 6) | VBUCTRL   | TRUE)   // Uplink gain amp 3dB, Sidetone gain to -17 dB
  #define  C_VBDCTRL        ((0x006 << 6) | VBDCTRL   | TRUE)   // Downlink gain amp 0dB, Volume control -12 dB
#if (RF_PA == 0 || RF_PA == 3) 
  #define  C_APCOFF         ((0x040 << 6) | APCOFF    | TRUE)  // x2 slope 128 
#elif (RF_PA == 1 || RF_PA == 2 || RF_PA == 4) 
  #define  C_APCOFF         ((0x070 << 6) | APCOFF    | TRUE)  // x2 slope 128 
#endif
  #define  C_BULIOFF        ((0x0FF << 6) | BULIOFF   | TRUE)   // value at reset
  #define  C_BULQOFF        ((0x0FF << 6) | BULQOFF   | TRUE)   // value at reset
  #define  C_DAI_ON_OFF     ((0x000 << 6) | APCOFF    | TRUE)   // value at reset
  #define  C_AUXDAC         ((0x000 << 6) | AUXDAC    | TRUE)   // value at reset
  #define  C_VBCTRL1        ((0x108 << 6) | VBCTRL1   | TRUE)   // VULSWITCH=1 AUXI 28,2 dB  
  #define  C_VBCTRL2        ((0x001 << 6) | VBCTRL2   | TRUE)   // HSMIC on, SPKG gain @ 2,5dB 

  // BULRUDEL will be initialized on rach only ....
  #define  C_APCDEL1        (((APCDEL_DOWN-2) << 11)  | ((APCDEL_UP-6)<<6) | APCDEL1)  
  #define  C_APCDEL2        ((0x000 << 6) | APCDEL2   | TRUE)                          //
  #define  C_BBCTRL         ((0x2C1 << 6) | BBCTRL    | TRUE)   // Internal autocalibration, Output common mode=1.35V
                                                         // Monoslot, Vpp=8/15*Vref                                             
  #define  C_BULGCAL        ((0x000 << 6) | BULGCAL   | TRUE) // IAG=0 dB, QAG=0 dB 

  #define  C_VBPOP          ((0x004 << 6) | VBPOP     | TRUE)  // HSOAUTO enabled only
  #define  C_VAUDINITD       2                           // vaud_init_delay init 2 frames
  #define  C_VAUDCTRL       ((0x000 << 6) | VAUDCTRL  | TRUE)  // Init to zero
  #define  C_VAUOCTRL       ((0x155 << 6) | VAUOCTRL  | TRUE)  // Speech on all outputs
  #define  C_VAUSCTRL       ((0x000 << 6) | VAUSCTRL  | TRUE)  // Init to zero
  #define  C_VAUDPLL        ((0x000 << 6) | VAUDPLL   | TRUE)  // Init to zero

  // SYREN registers values programmed by L1 directly through SPI (ABB_on)

  #define  C_BBCFG          (0x44)                               // Syren Like BDLF Filter - DC OFFSET removal OFF

#endif


/************************************/
/* Automatic frequency compensation */
/************************************/
/********************* C_Psi_sta definition *****************************/
/* C_Psi_sta = (2*pi*Fr)        / (N * Fb)                              */
/*      (1)  = (2*pi*V*ppm*0.9) / (N*V*Fb)                              */
/*           regarding Vega V/N   = 2.4/4096                            */
/*           regarding VCO  ppm/V = 16 / 1   (average slope of the VCO) */
/*      (1)  = (2*pi*2.4*16*0.9) / (4096*1*270.83)                      */
/*           = 0.000195748                                              */
/* C_Psi_sta_inv = 1/C_Psi_sta = 5108                                   */
/************************************************************************/

#ifdef CONFIG_TARGET_PIRELLI

/* matching Pirelli's fw as read out via rftr 9 */
#define  C_Psi_sta_inv    6974L    // (1/C_Psi_sta)
#define  C_Psi_st         8L       // C_Psi_sta * 0.8 F0.16
#define  C_Psi_st_32      492713L  // F0.32
#define  C_Psi_st_inv     8717L    // (1/C_Psi_st)

#elif defined(CONFIG_TARGET_GTAMODEM) || defined(CONFIG_TARGET_FCFAM)

/*
 * We calibrate our VCXO per unit following OM's precedent,
 * thus the compiled-in AFC params don't really matter on FC/OM targets,
 * but let's put in some numbers that are representative of our VCXO,
 * as opposed to the totally wrong numbers corresponding to the
 * significantly different VCXO on the original Leonardo.
 */

#define  C_Psi_sta_inv    3462L    // (1/C_Psi_sta)
#define  C_Psi_st         15L      // C_Psi_sta * 0.8 F0.16
#define  C_Psi_st_32      992326L  // F0.32
#define  C_Psi_st_inv     4328L    // (1/C_Psi_st)

#else

/* original TCS211 values */
#define  C_Psi_sta_inv    5419L    // (1/C_Psi_sta)
#define  C_Psi_st         10L      // C_Psi_sta * 0.8 F0.16
#define  C_Psi_st_32      634112L  // F0.32
#define  C_Psi_st_inv     6773L    // (1/C_Psi_st)

#endif

#if (VCXO_ALGO == 1)
// Linearity parameters

#ifdef CONFIG_TARGET_COMPAL
  /* matching Compal's fw as read out via rftr 9 */
  #define  C_AFC_DAC_CENTER     ((1000)*8)
  #define  C_AFC_DAC_MIN        ((-500)*8)
  #define  C_AFC_DAC_MAX        ((2500)*8)
#else
  /* original TCS211 values */
  #define  C_AFC_DAC_CENTER     ((111)*8)
  #define  C_AFC_DAC_MIN        ((-1196)*8)
  #define  C_AFC_DAC_MAX        ((1419)*8)
#endif

  #define  C_AFC_SNR_THR        2560     //  1/0.4    * 2**10
#endif

typedef struct
{
  WORD16  eeprom_afc;
  UWORD32 psi_sta_inv;
  UWORD32 psi_st;
  UWORD32 psi_st_32;
  UWORD32 psi_st_inv;

  #if (VCXO_ALGO)
  // VCXO adjustment parameters
  // Parameters used when assuming linearity
  WORD16  dac_center;
  WORD16  dac_min;
  WORD16  dac_max;
    WORD16  snr_thr;
  #endif
}
T_AFC_PARAMS;

/************************************/
/* Swap IQ definitions...           */
/************************************/
/* 0=No Swap, 1=Swap RX only, 2=Swap TX only, 3=Swap RX and TX */
#if (RF_PG == R_PG_10)
    // PG 1.0 -> 1 (Swap RX only)
    // GSM 850 => TX is ALWAYS swapped compared to GSM 900
    #define  SWAP_IQ_GSM    1
    #define  SWAP_IQ_DCS    1
    #define  SWAP_IQ_PCS    1
    #define  SWAP_IQ_GSM850 3   // Swap TX compared to GSM 900
#else
    // All PG versions ABOVE 1.0 -> 0 (No Swap)
    // GSM 850 => TX is ALWAYS swapped compared to GSM 900
    #define  SWAP_IQ_GSM    0
    #define  SWAP_IQ_DCS    0
    #define  SWAP_IQ_PCS    0
    #define  SWAP_IQ_GSM850 2   // Swap TX compared to GSM 900
#endif

/************************************/
/************************************/
// typedef
/************************************/
/************************************/

/*************************************************************/
/* Define structure for apc of TX Power                 ******/
/*************************************************************/
typedef struct 
{ // pcm-file "rf/tx/level.gsm|dcs"
  UWORD16 apc;            // 0..31
  UWORD8  ramp_index;     // 0..RF_TX_RAMP_SIZE
  UWORD8  chan_cal_index; // 0..RF_TX_CHAN_CAL_TABLE_SIZE
} 
T_TX_LEVEL;

/************************************/
/* Automatic Gain Control           */
/************************************/
/* Define structure for sub-band definition of TX Power ******/ 
typedef struct 
   {
   UWORD16  upper_bound;     //highest physical arfcn of the sub-band 
   WORD16    agc_calib;      // AGC  for each TXPWR
   }T_RF_AGC_BAND;

/************************************/
/*       Ramp definitions           */
/************************************/
#if ((ANLG_FAM == 1) || (ANLG_FAM == 2) || (ANLG_FAM == 3))
  typedef struct
  {
    UWORD8  ramp_up     [16];  // Ramp-up profile
    UWORD8  ramp_down   [16];  // Ramp-down profile
  }
  T_TX_RAMP;
#endif


// RF structure definition
//========================

// Number of bands supported
#define GSM_BANDS 2

#define MULTI_BAND1     0
#define MULTI_BAND2     1
// RF table sizes
#define RF_RX_CAL_CHAN_SIZE 10       // number of AGC sub-bands
#define RF_RX_CAL_TEMP_SIZE 11       // number of temperature ranges

#define RF_TX_CHAN_CAL_TABLE_SIZE  4 // channel calibration table size 
#define RF_TX_NUM_SUB_BANDS        8 // number of sub-bands in channel calibration table
#define RF_TX_LEVELS_TABLE_SIZE   32 // level table size  
#define RF_TX_RAMP_SIZE           16 // number of ramp definitions
#define RF_TX_CAL_TEMP_SIZE        5 // number of temperature ranges

#define AGC_TABLE_SIZE            20 
#define MIN_AGC_INDEX              6

#define TEMP_TABLE_SIZE          131 // number of elements in ADC->temp conversion table


// RX parameters and tables
//-------------------------

// AGC parameters and tables
typedef struct
{
  UWORD16 low_agc_noise_thr;
  UWORD16 high_agc_sat_thr;
  UWORD16 low_agc;
  UWORD16 high_agc;
  UWORD8  il2agc_pwr[121];
  UWORD8  il2agc_max[121];
  UWORD8  il2agc_av[121];
}
T_AGC;

// Calibration parameters
typedef struct
{
  UWORD16 g_magic;
  UWORD16 lna_att;
  UWORD16 lna_switch_thr_low;
  UWORD16 lna_switch_thr_high;
}
T_RX_CAL_PARAMS;   

// RX temperature compensation
typedef struct
{
  WORD16 temperature;
  WORD16 agc_calib;
}
T_RX_TEMP_COMP;

// RF RX structure
typedef struct
{
  T_AGC              agc;
}
T_RF_RX; //common

// RF RX structure
typedef struct
{
  T_RX_CAL_PARAMS rx_cal_params;
  T_RF_AGC_BAND   agc_bands[RF_RX_CAL_CHAN_SIZE];
  T_RX_TEMP_COMP  temp[RF_RX_CAL_TEMP_SIZE];
}
T_RF_RX_BAND;


// TX parameters and tables
//-------------------------

// TX temperature compensation
typedef struct
{
  WORD16 temperature;
  #if (ORDER2_TX_TEMP_CAL==1)
  WORD16 a;
  WORD16 b;
  WORD16 c;
  #else
  WORD16 apc_calib;          
  #endif
}
T_TX_TEMP_CAL;

// Ramp up and ramp down delay
typedef struct
{
  UWORD16 up;
  UWORD16 down;
}
T_RAMP_DELAY;

typedef struct 
{
  UWORD16 arfcn_limit;
  WORD16  chan_cal;
} 
T_TX_CHAN_CAL; 

// RF TX structure
typedef struct
{
  T_RAMP_DELAY   ramp_delay;
  UWORD8         guard_bits;  // number of guard bits needed for ramp up
  UWORD8         prg_tx;
}
T_RF_TX; //common
  
// RF TX structure
typedef struct
{
  T_TX_LEVEL           levels[RF_TX_LEVELS_TABLE_SIZE];
  T_TX_CHAN_CAL        chan_cal_table[RF_TX_CHAN_CAL_TABLE_SIZE][RF_TX_NUM_SUB_BANDS];
  T_TX_RAMP            ramp_tables[RF_TX_RAMP_SIZE];
  T_TX_TEMP_CAL        temp[RF_TX_CAL_TEMP_SIZE];
}
T_RF_TX_BAND;

// band structure 
typedef struct
{
  T_RF_RX_BAND  rx;
  T_RF_TX_BAND  tx;
  UWORD8        swap_iq;
}
T_RF_BAND;  
  
// RF structure 
typedef struct
{
  // common for all bands
  UWORD16      rf_revision;
  UWORD16      radio_band_support;
  T_RF_RX      rx;
  T_RF_TX      tx;
  T_AFC_PARAMS afc;
}
T_RF;

/************************************/
/*       MADC definitions           */
/************************************/
// Omega: 5 external channels if touch screen not used, 3 otherwise
enum ADC_INDEX {
   ADC_VBAT,
   ADC_VCHARG,
   ADC_ICHARG,
   ADC_VBACKUP,
   ADC_BATTYP,
   ADC_BATTEMP,
   ADC_ADC3,     // name of this ??
   ADC_RFTEMP,
   ADC_ADC4,
   ADC_INDEX_END // ADC_INDEX_END must be the end of the enums
};

typedef struct
{
    WORD16 converted[ADC_INDEX_END];  // converted
    UWORD16 raw[ADC_INDEX_END];       // raw from ADC
}
T_ADC;

/************************************/
/*       MADC calibration           */
/************************************/
typedef struct
{
   UWORD16 a[ADC_INDEX_END];
   WORD16 b[ADC_INDEX_END];
}
T_ADCCAL;

// Conversion table: ADC value -> temperature
typedef struct 
{
    UWORD16 adc;  // ADC reading is 10 bits
    WORD16  temp; // temp is in approx. range -30..+80
}
T_TEMP;

typedef struct
{
    char *name;
    void *addr;
    int  size;
}
T_CONFIG_FILE;

typedef struct
{
  char      *name;         // name of ffs file suffix
  T_RF_BAND *addr;         // address to default flash structure
  UWORD16   max_carrier;   // max carrier 
  UWORD16   max_txpwr;     // max tx power
}
T_BAND_CONFIG;

typedef struct
{
  UWORD8  band[GSM_BANDS]; // index to band address
  UWORD8  txpwr_tp;        // tx power turning point  
  UWORD16 first_arfcn;     // first index
}
T_STD_CONFIG;
enum GSMBAND_DEF 
{
  BAND_NONE,
  BAND_EGSM900,
  BAND_DCS1800,
  BAND_PCS1900,
  BAND_GSM850,
  // put new bands here
  BAND_GSM900  //last entry
};

/************************************/
/* ABB (Omega) Initialization       */
/************************************/

#if ((ANLG_FAM == 1) || (ANLG_FAM == 2))
#define ABB_TABLE_SIZE 16
#elif (ANLG_FAM == 3)
  #define ABB_TABLE_SIZE 22
#endif

// Note that this translation is probably not needed at all. But until L1 is
// (maybe) changed to simply initialize the ABB from a table of words, we
// use this to make things more easy-readable.

#if (ANLG_FAM == 1)
  enum ABB_REGISTERS {
    ABB_AFCCTLADD = 0,
    ABB_VBUCTRL,
    ABB_VBDCTRL,
    ABB_BBCTRL,
    ABB_APCOFF,
    ABB_BULIOFF,
    ABB_BULQOFF,
    ABB_DAI_ON_OFF,
    ABB_AUXDAC,
    ABB_VBCTRL,
    ABB_APCDEL1
  };
#elif (ANLG_FAM == 2)
  enum ABB_REGISTERS {
    ABB_AFCCTLADD = 0,
    ABB_VBUCTRL,
    ABB_VBDCTRL,
    ABB_BBCTRL,
    ABB_BULGCAL,
    ABB_APCOFF,
    ABB_BULIOFF,
    ABB_BULQOFF,
    ABB_DAI_ON_OFF,
    ABB_AUXDAC,
    ABB_VBCTRL1,
    ABB_VBCTRL2,
    ABB_APCDEL1,
    ABB_APCDEL2
  };
#elif (ANLG_FAM == 3)
  enum ABB_REGISTERS {
    ABB_AFCCTLADD = 0,
    ABB_VBUCTRL,
    ABB_VBDCTRL,
    ABB_BBCTRL,
    ABB_BULGCAL,
    ABB_APCOFF,
    ABB_BULIOFF,
    ABB_BULQOFF,
    ABB_DAI_ON_OFF,
    ABB_AUXDAC,
    ABB_VBCTRL1,
    ABB_VBCTRL2,
    ABB_APCDEL1,
    ABB_APCDEL2,
    ABB_VBPOP,
    ABB_VAUDINITD,
    ABB_VAUDCTRL,
    ABB_VAUOCTRL,
    ABB_VAUSCTRL,
    ABB_VAUDPLL
  };
#endif
#endif