FreeCalypso > hg > fc-magnetite
view src/cs/layer1/include/l1_confg.h @ 624:012028896cfb
FFS dev.c, Leonardo target: Fujitsu MB84VF5F5F4J2 #if 0'ed out
The FFS code we got from TI/Openmoko had a stanza for "Fujitsu MB84VF5F5F4J2
stacked device", using a fake device ID code that would need to be patched
manually into cfgffs.c (suppressing and overriding autodetection) and using
an FFS base address in the nCS2 bank, indicating that this FFS config was
probably meant for the MCP version of Leonardo which allows for 16 MiB flash
with a second bank on nCS2.
We previously had this FFS config stanza conditionalized under
CONFIG_TARGET_LEONARDO because the base address contained therein is invalid
for other targets, but now that we actually have a Leonardo build target in
FC Magnetite, I realize that the better approach is to #if 0 out this stanza
altogether: it is already non-functional because it uses a fake device ID
code, thus it is does not add support for more Leonardo board variants,
instead it is just noise.
| author | Mychaela Falconia <falcon@freecalypso.org> |
|---|---|
| date | Sun, 22 Dec 2019 21:24:29 +0000 |
| parents | 945cf7f506b2 |
| children |
line wrap: on
line source
/************* Revision Controle System Header ************* * GSM Layer 1 software * L1_CONFG.H * * Filename l1_confg.h * Copyright 2003 (C) Texas Instruments * ************* Revision Controle System Header *************/ #ifndef __L1_CONFG_H__ #define __L1_CONFG_H__ #ifndef _WINDOWS #include "l1sw.cfg" // Configuration Software #include "board.cfg" #include "chipset.cfg" #include "rf.cfg" #include "swconfig.cfg" #include "sys.cfg" #endif // Traces... // TRACE_TYPE == 1,2,3 are used in standalone mode (L2-L3 Simul) with USART // TRACE_TYPE == 4 is used on A-sample only (with UART): L1 + protocol stack // TRACE_TYPE == 1 -> L1/L3 interface trace // TRACE_TYPE == 2 -> Trace mode: ~33~~1~011... // TRACE_TYPE == 3 -> same as above (2) plus FER or stats trace // TRACE_TYPE == 4 -> L1/L3 interface trace on A-sample with protocol stack // TRACE_TYPE == 5 -> trace for full simulation // TRACE_TYPE == 6 -> CPU load trace for hisr // TRACE_TYPE == 7 -> CPU LOAD trace for layer 1 hisr for all TDMA. Output on // UART at 38400 bps => // format : <hisr cpu value in microseconds> <frame number> // Code PB reported workaround //------------------------------ // Code Version possible choices //------------------------------ #define SIMULATION 1 #define NOT_SIMULATION 2 // RCL functions Version possible choices //------------------------------ #define POLL_FORCED 0 #define RLC_SCENARIO 1 #define MODEM_FLOW 2 // possible choices for UART trace output //------------------------------ #define MODEM_UART 0 #define IRDA_UART 1 #if (CHIPSET == 12) #define MODEM2_UART 2 #endif //============ // CODE CHOICE //============ #if (OP_L1_STANDALONE==0) #define CODE_VERSION NOT_SIMULATION #else // OP_L1_STANDALONE #ifdef WIN32 #define CODE_VERSION SIMULATION #else // WIN32 #define CODE_VERSION NOT_SIMULATION #endif // WIN32 #endif // OP_L1_STANDALONE //--------------------------------------------------------------------------------- // Test with full simulation. //--------------------------------------------------------------------------------- #if (CODE_VERSION == SIMULATION) // Test Scenari... #define SCENARIO_FILE 1 // Test Scenario comes from input files. #define SCENARIO_MEM 0 // Test Scenario comes from RAM. // Traces... #undef TRACE_TYPE #define TRACE_TYPE 5 #define LOGFILE_TRACE 1 // trace in an output logfile #define FLOWCHART 0 // Message sequence/flow chart trace. #define NUCLEUS_TRACE 0 // Nucleus error trace #define EOTD_TRACE 1 // EOTD log trace #define TRACE_FULL_NAME 0 // display full fct names after a PM/COM error #define L2_L3_SIMUL 1 // Layer 2 & Layer 3 simulated, main within NU_MAIN.C, trace possible. // Control algorithms... #define AFC_ALGO 1 // AFC algorithm. #define TOA_ALGO 1 // TOA algorithm. #define AGC_ALGO 1 // AGC algorithm. #define TA_ALGO 0 // TA (Timing Advance) algorithm. #undef VCXO_ALGO #define VCXO_ALGO 0 // VCXO algo #undef DCO_ALGO #define DCO_ALGO 0 // DCO algo (TIDE) #undef ORDER2_TX_TEMP_CAL #define ORDER2_TX_TEMP_CAL 0 // TX Temperature Compensation Algorithm selection #define FACCH_TEST 0 // FACCH test enabled. #define ADC_TIMER_ON 0 // Timer for ADC measurements #define AFC_ON 1 // Enable of the Omega AFC module #define AUDIO_TASK 1 // Enable the L1 audio features #define AUDIO_SIMULATION 1 // Audio simulator for the audio tasks (works only with the new audio design i.e. AUDIO_TASK=1) #define AUDIO_L1_STANDALONE 0 // Flag to enable the audio simulator used with the L1 stand-alone (works only with the new audio design i.e. AUDIO_TASK=1) #define GTT_SIMULATION 1 // Gtt simulator for the gtt tasks (works only with if L1_GTT=1) #define TTY_SYNC_MCU 1 // TTY WORKAROUND BUG03401 #define TTY_SYNC_MCU_2 1 // #define L1_GTT_FIFO_TEST_ATOMIC 0 // #define NEW_WKA_PATCH 0 #define OPTIMISED 1 #define L1_RECOVERY 0 // L1 recovery #undef L1_GPRS #define L1_GPRS 1 // GPRS L1: MS supporting both Circuit Switched and Packet (GPRS) capabilities #undef AMR #define AMR 1 // AMR version 1.0 supported #undef L1_12NEIGH #define L1_12NEIGH 1 // new L1-RR interface for 12 neighbour cells #undef L1_GTT #define L1_GTT 1 // Enable Global Text Telephony feature for simulation #undef OP_L1_STANDALONE #define OP_L1_STANDALONE 1 // Selection of code for L1 stand alone #undef OP_RIV_AUDIO #define OP_RIV_AUDIO 0 // Selection of code for Riviera audio #undef OP_WCP #define OP_WCP 0 // No WCP integration //--------------------------------------------------------------------------------- // Test with H/W platform. //--------------------------------------------------------------------------------- #elif (CODE_VERSION == NOT_SIMULATION) #define WA_PCTM_AGC_PARAMS 0 // to work by default with 4 parameters to calibration (compatible with PCTM if 1) // Work around about Calypso RevA: the bus is floating (Cf PB01435) // (corrected with Calypso ReV B and Calypso C035) #if (CHIPSET == 7) #define W_A_CALYPSO_BUG_01435 1 #else #define W_A_CALYPSO_BUG_01435 0 #endif // for AMR thresolds definition CQ22226 #define AMR_THRESHOLDS_WORKAROUND 1 #if (L1_GTT==1) #define TTY_SYNC_MCU 1 #define TTY_SYNC_MCU_2 1 #define L1_GTT_FIFO_TEST_ATOMIC 0 #define NEW_WKA_PATCH 0 #define OPTIMISED 1 #else #define TTY_SYNC_MCU_2 0 #define L1_GTT_FIFO_TEST_ATOMIC 0 #define TTY_SYNC_MCU 0 #define NEW_WKA_PATCH 0 #define OPTIMISED 0 #endif // Traces... #define NUCLEUS_TRACE 0 // Nucleus error trace #define FLOWCHART 0 // Message sequence/flow chart trace. #define LOGFILE_TRACE 0 // trace in an output logfile #define TRACE_FULL_NAME 0 // display full fct names after a PM/COM error // Test Scenari... #define SCENARIO_FILE 0 // Test Scenario comes from input files. #define SCENARIO_MEM 1 // // Test Scenario comes from RAM. #if (OP_L1_STANDALONE == 1) #define L2_L3_SIMUL 1 // Layer 2 & Layer 3 simulated, main within NU_MAIN.C, trace possible. #else #define L2_L3_SIMUL 0 #endif // Control algorithms... #define AFC_ALGO 1 // AFC algorithm. //TOA Algorithm needs to be on for TestMode, otherwise no dedic test will be succesful!!! #define TOA_ALGO 1 // TOA algorithm. #define AGC_ALGO 1 // AGC algorithm. #define TA_ALGO 1 // TA (Timing Advance) algorithm. #define FACCH_TEST 0 // FACCH test enabled. #define ADC_TIMER_ON 0 // Timer for ADC measurements #define AFC_ON 1 // Enable of the Omega AFC module #define AUDIO_TASK 1 // Enable the L1 audio features #define AUDIO_SIMULATION 0 // Audio simulator for the audio tasks (works only with the new audio design i.e. AUDIO_TASK=1) #if (OP_L1_STANDALONE == 1) #define AUDIO_L1_STANDALONE 1 // Flag to enable the audio simulator used with the L1 stand-alone (works only with the new audio design i.e. AUDIO_TASK=1) #else #define AUDIO_L1_STANDALONE 0 #endif #define GTT_SIMULATION 0 // Gtt simulator for the gtt tasks (works only with if L1_GTT=1) #define OP_BT 0 // Simulation of ISLAND (BLUETOOTH) sleep management #define L1_RECOVERY 1 // L1 recovery #if (L1_GPRS == 1) #define RLC_VERSION RLC_SCENARIO #if (RLC_VERSION == RLC_SCENARIO) #define RLC_DL_BLOCK_STAT 0 // Works with RLC_VERSION = RLC_SCENARIO // output stat on CRC error blocks // The user must enter the cs type and // the number of frames desired. #else #define RLC_DL_BLOCK_STAT 0 // Default value; Never change it #endif #if (OP_L1_STANDALONE == 1) #define DSP_BACKGROUND_TASKS 1 // Enable the TEST of DSP background.tasks // activated by a layer 3 message (BG_TASK_START (<task number>)) // deactivated by a layer 3 message (BG_TASK_STOP (<task number>)) // Warning : Works only with DSP>=31 #else #define DSP_BACKGROUND_TASKS 0 #endif #else #define DSP_BACKGROUND_TASKS 0 #define RLC_DL_BLOCK_STAT 0 // Default value; Never change it #endif #endif // Audio tasks selection //----------------------- #if (AUDIO_TASK == 1) #define KEYBEEP 1 // Enable keybeep feature #define TONE 1 // Enable tone feature // Temporary modification for protocol stack compatibility - GSMLITE will be removed #if (OP_L1_STANDALONE == 1) #define GSMLITE 1 #endif #if ((OP_L1_STANDALONE == 1) || (!GSMLITE)) #define MELODY_E1 1 // Enable melody format E1 feature #define VOICE_MEMO 1 // Enable voice memorization feature #define FIR 1 // Enable FIR feature #if (DSP == 33) || (DSP == 34) || (DSP == 35) || (DSP == 36) #define AUDIO_MODE 1 // Enable Audio mode feature #else #define AUDIO_MODE 0 // Disable Audio mode feature #endif #else #define MELODY_E1 0 // Disable melody format E1 feature #define VOICE_MEMO 0 // Disable voice memorization feature #if (MELODY_E2) #define FIR 1 // Enable FIR feature #else #define FIR 0 // Disable FIR feature #endif #define AUDIO_MODE 0 // Disable Audio mode feature #endif // Define CPORT for ESample only #if ((CHIPSET == 12) && ((DSP == 35) || (DSP == 36))) #define L1_CPORT 1 // Enable cport feature #else #define L1_CPORT 0 // Disable cport feature #endif #else #define KEYBEEP 0 // Enable keybeep feature #define TONE 0 // Enable tone feature #define MELODY_E1 0 // Enable melody format E1 feature #define VOICE_MEMO 0 // Enable voice memorization feature #define FIR 0 // Enable FIR feature #define AUDIO_MODE 0 // Enable Audio mode feature #define L1_CPORT 0 // Enable cport feature #endif #define L1_AUDIO_BACKGROUND_TASK (SPEECH_RECO | MELODY_E2) // audio background task is used by speech reco and melody_e2 #if (OP_RIV_AUDIO == 1) #define L1_AUDIO_DRIVER L1_VOICE_MEMO_AMR // Riviera audio driver (only Voice Memo AMR is available) #endif // Vocoder selections //------------------- #define FR 1 // Full Rate #define FR_HR 2 // Full Rate + Half Rate #define FR_EFR 3 // Full Rate + Enhanced Full Rate #define FR_HR_EFR 4 // Full Rate + Half Rate + Enhanced Full Rate // Standard (frequency plan) selections //------------------------------------- #define GSM 1 // GSM900. #define GSM_E 2 // GSM900 Extended. #define PCS1900 3 // PCS1900. #define DCS1800 4 // DCS1800. #define DUAL 5 // Dual Band (GSM900 + DCS 1800 bands) #define DUALEXT 6 // Dual Band (E-GSM900 + DCS 1800 bands) #define GSM850 7 // GSM850 Band #define DUAL_US 8 // PCS1900 + GSM850 /*------------------------------------*/ /* Power Management */ /*------------------------------------*/ #define PWR_MNGT 1 // POWER management active if l1_config.pwr_mngt=1 /*---------------------------------------------------------------------------*/ /* DSP configurations */ /* ------------------ */ /* DSP | FR| HR|EFR|14.4| SPEED |12LA68|12LA68 |4L32|AEC| MCU/DSP */ /* (version) | | | | | |POLE80|POLE112| |/NS| interface */ /* ----------+---+---+---+----+---------+------+-------+----+---+---------- */ /* 0 (821) | x | | | | 39Mhz | x | | | | 1 */ /* ----------+---+---+---+----+---------+------+-------+----+---+---------- */ /* 1 (830) | x | | | | 39Mhz | (1) | | x | | 1 */ /* ----------+---+---+---+----+---------+------+-------+----+---+---------- */ /* 2 (912) | x | x | | | 58.5Mhz | x | | | | 2 */ /* ----------+---+---+---+----+---------+------+-------+----+---+---------- */ /* 3 (10xx) | x | | x | x | 65Mhz | x | | | x | 3 */ /* ----------+---+---+---+----+---------+------+-------+----|---+---------- */ /* 4 (11xx) | x | x | x | x | 65Mhz | x | x (3)| | x | 3 */ /* ----------+---+---+---+----+---------+------+-------+----+---+---------- */ /* 5 (830) | x | | | | 39Mhz | x | | | | 1 */ /* ----------+---+---+---+----+---------+------+-------+----+---+---------- */ /* 6 (11xx) | x | x | x | x | 65Mhz | x | x (3)| |(2)| 3 */ /* ----------+---+---+---+----+---------+------+-------+----+---+---------- */ /* */ /*(1) this version can be loaded on a 12LA68/POLE80 but the RIF/DL problem is*/ /* not corrected. */ /* */ /*(2) AEC is disabled at DSP level but L1 must be compiled with MCU/DSP */ /* interface which support AEC, therefore AEC is defined as 1. */ /* */ /*(3) Pole112 include RIF DL correction. No patch is needed if this one only */ /* include RIF/DL problem. */ /* */ /*---------------------------------------------------------------------------*/ #if (DSP == 16 || DSP == 17) /* #define CLKMOD1 0x414e // ... #define CLKMOD2 0x414e // ...65 Mips #define CLKSTART 0x29 // ...65 Mips */ #define CLKMOD1 0x4006 // ... #define CLKMOD2 0x4116 // ...65 Mips pll free #define CLKSTART 0x29 // ...65 Mips /* #define CLKMOD1 0x2116 //This settings force the DSP to never enteridle #define CLKMOD2 0x2116 //In this case the PLL will be always on. 39 Mips #define CLKSTART 0x25 // ...39 Mips */ #define VOC FR_HR_EFR // FR + HR + EFR. #define DATA14_4 1 // No 14.4 data allowed. #define AEC 1 // AEC/NS supported. #define MAP 3 #define DSP_START 0x2000 #define W_A_DSP1 0 // Work Around correcting pb in DSP: SACCH #define W_A_DSP_SR_BGD 0 // Work around about the DSP speech reco background task. /* DSP debug trace configuration */ /*-------------------------------*/ #if (MELODY_E2) // In case of the melody E2 the DSP trace must be disable because the // melody instrument waves are overlayed with DSP trace buffer // DSP debug trace API buufer config #define C_DEBUG_BUFFER_ADD 0x17ff // Address of DSP write pointer... data are just after. #define C_DEBUG_BUFFER_SIZE 7 // Real size is incremented by 1 for DSP write pointer. #else // DSP debug trace API buufer config #define C_DEBUG_BUFFER_ADD 0x17ff // Address of DSP write pointer... data are just after. #define C_DEBUG_BUFFER_SIZE 2047 // Real size is incremented by 1 for DSP write pointer. #endif #elif (DSP == 30) // First GPRS. #define CLKMOD1 0x4006 // ... #define CLKMOD2 0x4116 // ...65 Mips pll free #define CLKSTART 0x29 // ...65 Mips #define VOC FR_HR_EFR // FR + HR + EFR. #define DATA14_4 1 // No 14.4 data allowed. #define AEC 1 // AEC/NS not supported. #define MAP 3 #define DSP_START 0x1F81 #define W_A_DSP1 0 // Work Around correcting pb in DSP: SACCH #define ULYSSE 0 #define W_A_DSP_SR_BGD 0 // Work around about the DSP speech reco background task. #elif (DSP == 31) // ROM Code GPRS G0. #define CLKMOD1 0x4006 // ... #define CLKMOD2 0x4116 // ...65 Mips pll free #define CLKSTART 0x29 // ...65 Mips #define VOC FR_HR_EFR // FR + HR + EFR (normaly FR_EFR : PBs). #define DATA14_4 1 // 14.4 data allowed. #define AEC 1 // AEC/NS not supported. #define MAP 3 #define DSP_START 0x8763 #define INSTALL_ADD 0x87c9 // Used to set gprs_install_address pointer #define INSTALL_ADD_WITH_PATCH 0x1352 // Used to set gprs_install_address pointer #define W_A_DSP1 0 // Work Around correcting pb in DSP: SACCH #define ULYSSE 0 #define W_A_DSP_SR_BGD 0 // Work around about the DSP speech reco background task. #elif (DSP == 32) // ROM Code GPRS G1. #define CLKMOD1 0x4006 // ... #define CLKMOD2 0x4116 // ...65 Mips pll free #define CLKSTART 0x29 // ...65 Mips #define VOC FR_HR_EFR // FR + HR + EFR (normaly FR_EFR : PBs). #define DATA14_4 1 // 14.4 data allowed. #define AEC 1 // AEC/NS not supported. #define MAP 3 #define DSP_START 0x8763 #define INSTALL_ADD 0x87c9 // Used to set gprs_install_address pointer #define W_A_DSP1 0 // Work Around correcting pb in DSP: SACCH #define ULYSSE 0 #define W_A_DSP_SR_BGD 0 // Work around about the DSP speech reco background task. #elif (DSP == 33) // ROM Code GPRS. #define CLKMOD1 0x4006 // ... #define CLKMOD2 0x4116 // ...65 Mips pll free #define CLKSTART 0x29 // ...65 Mips #define C_PLL_CONFIG 0x154 // For VTCXO = 13 MHz and max DSP speed = 84.5 Mips #define VOC FR_HR_EFR // FR + HR + EFR (normaly FR_EFR : PBs). #define AEC 1 // AEC/NS not supported. #if (OP_RIV_AUDIO == 0) #define L1_NEW_AEC 1 #else // Available but not yet tuned with Riviera AUDIO #define L1_NEW_AEC 0 #endif #if ((L1_NEW_AEC) && (!AEC)) // First undef the flag to avoid warnings at compilation time #undef AEC #define AEC 1 #endif #define MAP 3 #define DSP_START 0x7000 #define INSTALL_ADD 0x7002 // Used to set gprs_install_address pointer #define W_A_DSP1 0 // Work Around correcting pb in DSP: SACCH #define ULYSSE 0 #define W_A_DSP_SR_BGD 1 // Work around about the DSP speech reco background task. #if ( (CHIPSET != 12) && (CODE_VERSION == NOT_SIMULATION)) #define W_A_DSP_IDLE3 1 // Work around to report DSP state to the ARM for Deep Sleep // management. // DSP_IDLE3 is not supported in simulation #else #define W_A_DSP_IDLE3 0 #endif // DSP software work-around config // bit0 - Work-around to support CRTG. // bit1 - DMA reset on critical DMA still running cases, refer to REQ01260. // bit2 - Solve Read/Write BULDATA pointers Omega & Nausica issue, refer to BUG00650. // bit3 - Solve IBUFPTRx reset IOTA issue, refer to BUG01911. #if (ANLG_FAM == 1) // OMEGA / NAUSICA #define C_DSP_SW_WORK_AROUND 0x0006 #elif (ANLG_FAM == 2) // IOTA #define C_DSP_SW_WORK_AROUND 0x000E #elif (ANLG_FAM == 3) // SYREN #define C_DSP_SW_WORK_AROUND 0x000E #endif /* DSP debug trace configuration */ /*-------------------------------*/ #if (MELODY_E2) // In case of the melody E2 the DSP trace must be disable because the // melody instrument waves are overlayed with DSP trace buffer // DSP debug trace API buufer config #define C_DEBUG_BUFFER_ADD 0x17ff // Address of DSP write pointer... data are just after. #define C_DEBUG_BUFFER_SIZE 7 // Real size is incremented by 1 for DSP write pointer. // DSP debug trace type config // |<-------------- Features -------------->|<---------- Levels ----------->| // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR] #define C_DEBUG_TRACE_TYPE 0x0000 // Level = BASIC; Features = Timer + Buffer Header + Burst. #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4)) #define DSP_DEBUG_TRACE_ENABLE 1 // Enable DSP debug trace dumping capability // Currently not supported ! #endif #else // DSP debug trace API buufer config #define C_DEBUG_BUFFER_ADD 0x17ff // Address of DSP write pointer... data are just after. #define C_DEBUG_BUFFER_SIZE 2047 // Real size is incremented by 1 for DSP write pointer. // DSP debug trace type config // |<-------------- Features -------------->|<---------- Levels ----------->| // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR] #define C_DEBUG_TRACE_TYPE 0x0012 // Level = BASIC; Features = Buffer Header. #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4)) #define DSP_DEBUG_TRACE_ENABLE 1 // Enable DSP debug trace dumping capability (supported since patch 2090) #endif #endif /* d_error_status */ /*-------------------------------*/ #if ((TRACE_TYPE == 1) || (TRACE_TYPE == 4)) #define D_ERROR_STATUS_TRACE_ENABLE 1 // Enable d_error_status checking capability (supported since patch 2090) // masks to apply on d_error_status bit field for DSP patch 0x2061 or 0x2062 #define DSP_DEBUG_GSM_MASK 0x0000 #define DSP_DEBUG_GPRS_MASK 0x0f3d #endif #if DCO_ALGO // DCO type of scheduling #define C_CN_DCO_PARAM 0xA248 #endif #elif (DSP == 34) // ROM Code GPRS AMR. #define CLKMOD1 0x4006 // ... #define CLKMOD2 0x4116 // ...65 Mips pll free #define CLKSTART 0x29 // ...65 Mips #define C_PLL_CONFIG 0x154 // For VTCXO = 13 MHz and max DSP speed = 84.5 Mips #define VOC FR_HR_EFR // FR + HR + EFR (normaly FR_EFR : PBs). #define AEC 1 // AEC/NS not supported. #if (OP_RIV_AUDIO == 0) #define L1_NEW_AEC 1 #else // Available but not yet tuned with Riviera AUDIO #define L1_NEW_AEC 0 #endif #if ((L1_NEW_AEC) && (!AEC)) // First undef the flag to avoid warnings at compilation time #undef AEC #define AEC 1 #endif #define MAP 3 #define DSP_START 0x7000 #define INSTALL_ADD 0x7002 // Used to set gprs_install_address pointer #define W_A_DSP1 0 // Work Around correcting pb in DSP: SACCH #define ULYSSE 0 #define W_A_DSP_SR_BGD 1 // Work around about the DSP speech reco background task. #if ( (CHIPSET != 12) && (CODE_VERSION == NOT_SIMULATION)) #define W_A_DSP_IDLE3 1 // Work around to report DSP state to the ARM for Deep Sleep // management. // DSP_IDLE3 is not supported in simulation #else #define W_A_DSP_IDLE3 0 #endif // DSP software work-around config // bit0 - Work-around to support CRTG. // bit1 - DMA reset on critical DMA still running cases, refer to REQ01260. // bit2 - Solve Read/Write BULDATA pointers Omega & Nausica issue, refer to BUG00650. // bit3 - Solve IBUFPTRx reset IOTA issue, refer to BUG01911. #if (ANLG_FAM == 1) // OMEGA / NAUSICA #define C_DSP_SW_WORK_AROUND 0x0006 #elif (ANLG_FAM == 2) // IOTA #define C_DSP_SW_WORK_AROUND 0x000E #elif (ANLG_FAM == 3) // SYREN #define C_DSP_SW_WORK_AROUND 0x000E #endif /* DSP debug trace configuration */ /*-------------------------------*/ #if (MELODY_E2) // In case of the melody E2 the DSP trace must be disable because the // melody instrument waves are overlayed with DSP trace buffer // DSP debug trace API buufer config #define C_DEBUG_BUFFER_ADD 0x17ff // Address of DSP write pointer... data are just after. #define C_DEBUG_BUFFER_SIZE 7 // Real size is incremented by 1 for DSP write pointer. // DSP debug trace type config // |<-------------- Features -------------->|<---------- Levels ----------->| // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR] #define C_DEBUG_TRACE_TYPE 0x0000 // Level = BASIC; Features = Timer + Buffer Header + Burst. #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4)) #define DSP_DEBUG_TRACE_ENABLE 1 // Enable DSP debug trace dumping capability // Currently not supported ! #endif #else // DSP debug trace API buufer config #define C_DEBUG_BUFFER_ADD 0x17ff // Address of DSP write pointer... data are just after. #define C_DEBUG_BUFFER_SIZE 2047 // Real size is incremented by 1 for DSP write pointer. // DSP debug trace type config // |<-------------- Features -------------->|<---------- Levels ----------->| // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR] #define C_DEBUG_TRACE_TYPE 0x0012 // Level = BASIC; Features = Buffer Header. #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4)) #define DSP_DEBUG_TRACE_ENABLE 1 // Enable DSP debug trace dumping capability (supported since patch 2090) #endif // AMR trace #define C_AMR_TRACE_ID 55 #endif /* d_error_status */ /*-------------------------------*/ #if ((TRACE_TYPE == 1) || (TRACE_TYPE == 4)) #define D_ERROR_STATUS_TRACE_ENABLE 1 // Enable d_error_status checking capability (supported since patch 2090) // masks to apply on d_error_status bit field #define DSP_DEBUG_GSM_MASK 0x0000 #define DSP_DEBUG_GPRS_MASK 0x0f3d #endif #elif (DSP == 35) // ROM Code GPRS AMR. #define CLKMOD1 0x4006 // ... #define CLKMOD2 0x4116 // ...65 Mips pll free #define CLKSTART 0x29 // ...65 Mips #define C_PLL_CONFIG 0x154 // For VTCXO = 13 MHz and max DSP speed = 84.5 Mips #define VOC FR_HR_EFR // FR + HR + EFR (normaly FR_EFR : PBs). #define AEC 1 // AEC/NS not supported. #if (OP_RIV_AUDIO == 0) #define L1_NEW_AEC 1 #else // Available but not yet tuned with Riviera AUDIO #define L1_NEW_AEC 0 #endif #if ((L1_NEW_AEC) && (!AEC)) // First undef the flag to avoid warnings at compilation time #undef AEC #define AEC 1 #endif #define MAP 3 #define FF_L1_TCH_VOCODER_CONTROL 1 #define L1M_WAIT_DSP_RESTART_AFTER_VOCODER_ENABLE 1 #define DSP_START 0x7000 #define INSTALL_ADD 0x7002 // Used to set gprs_install_address pointer #define W_A_DSP1 0 // Work Around correcting pb in DSP: SACCH #define ULYSSE 0 #define W_A_DSP_SR_BGD 1 // Work around about the DSP speech reco background task. #if ( (CHIPSET != 12) && (CODE_VERSION == NOT_SIMULATION)) #define W_A_DSP_IDLE3 1 // Work around to report DSP state to the ARM for Deep Sleep // management. // DSP_IDLE3 is not supported in simulation #else #define W_A_DSP_IDLE3 0 #endif // DSP software work-around config // bit0 - Work-around to support CRTG. // bit1 - DMA reset on critical DMA still running cases, refer to REQ01260. // bit2 - Solve Read/Write BULDATA pointers Omega & Nausica issue, refer to BUG00650. // bit3 - Solve IBUFPTRx reset IOTA issue, refer to BUG01911. #if (ANLG_FAM == 1) // OMEGA / NAUSICA #define C_DSP_SW_WORK_AROUND 0x0006 #elif (ANLG_FAM == 2) // IOTA #define C_DSP_SW_WORK_AROUND 0x000E #elif (ANLG_FAM == 3) // SYREN #define C_DSP_SW_WORK_AROUND 0x000E #endif /* DSP debug trace configuration */ /*-------------------------------*/ #if (MELODY_E2) // In case of the melody E2 the DSP trace must be disable because the // melody instrument waves are overlayed with DSP trace buffer // DSP debug trace API buufer config #define C_DEBUG_BUFFER_ADD 0x17ff // Address of DSP write pointer... data are just after. #define C_DEBUG_BUFFER_SIZE 7 // Real size is incremented by 1 for DSP write pointer. // DSP debug trace type config // |<-------------- Features -------------->|<---------- Levels ----------->| // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR] #define C_DEBUG_TRACE_TYPE 0x0000 // Level = BASIC; Features = Timer + Buffer Header + Burst. #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4)) #define DSP_DEBUG_TRACE_ENABLE 1 // Enable DSP debug trace dumping capability // Currently not supported ! #endif #else // DSP debug trace API buufer config #define C_DEBUG_BUFFER_ADD 0x17ff // Address of DSP write pointer... data are just after. #define C_DEBUG_BUFFER_SIZE 2047 // Real size is incremented by 1 for DSP write pointer. // DSP debug trace type config // |<-------------- Features -------------->|<---------- Levels ----------->| // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR] #define C_DEBUG_TRACE_TYPE 0x0012 // Level = BASIC; Features = Timer + Buffer Header + Burst. #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4)) #define DSP_DEBUG_TRACE_ENABLE 1 // Enable DSP debug trace dumping capability (supported since patch 2090) #endif // AMR trace #define C_AMR_TRACE_ID 55 #endif /* d_error_status */ /*-------------------------------*/ #if ((TRACE_TYPE == 1) || (TRACE_TYPE == 4)) #define D_ERROR_STATUS_TRACE_ENABLE 1 // Enable d_error_status checking capability (supported since patch 2090) // masks to apply on d_error_status bit field for DSP patch 0x2061 or 0x2062 #define DSP_DEBUG_GSM_MASK 0x08BD #define DSP_DEBUG_GPRS_MASK 0x0f3d #endif #elif (DSP == 36) // ROM Code GPRS AMR. #define CLKMOD1 0x4006 // ... #define CLKMOD2 0x4116 // ...65 Mips pll free #define CLKSTART 0x29 // ...65 Mips #define C_PLL_CONFIG 0x154 // For VTCXO = 13 MHz and max DSP speed = 84.5 Mips #define VOC FR_HR_EFR // FR + HR + EFR (normaly FR_EFR : PBs). #define AEC 1 // AEC/NS not supported. #if (OP_RIV_AUDIO == 0) #define L1_NEW_AEC 1 #else // Available but not yet tuned with Riviera AUDIO #define L1_NEW_AEC 0 #endif #if ((L1_NEW_AEC) && (!AEC)) // First undef the flag to avoid warnings at compilation time #undef AEC #define AEC 1 #endif #define MAP 3 #undef L1_AMR_NSYNC #define L1_AMR_NSYNC 1 #define FF_L1_TCH_VOCODER_CONTROL 1 #define L1M_WAIT_DSP_RESTART_AFTER_VOCODER_ENABLE 1 #define DSP_START 0x7000 #define INSTALL_ADD 0x7002 // Used to set gprs_install_address pointer #define W_A_DSP1 0 // Work Around correcting pb in DSP: SACCH #define ULYSSE 0 #define W_A_DSP_SR_BGD 1 // Work around about the DSP speech reco background task. #if ( (CHIPSET != 12) && (CODE_VERSION == NOT_SIMULATION)) #define W_A_DSP_IDLE3 1 // Work around to report DSP state to the ARM for Deep Sleep // management. // DSP_IDLE3 is not supported in simulation #else #define W_A_DSP_IDLE3 0 #endif // DSP software work-around config // bit0 - Work-around to support CRTG. // bit1 - DMA reset on critical DMA still running cases, refer to REQ01260. // bit2 - Solve Read/Write BULDATA pointers Omega & Nausica issue, refer to BUG00650. // bit3 - Solve IBUFPTRx reset IOTA issue, refer to BUG01911. #if (ANLG_FAM == 1) // OMEGA / NAUSICA #define C_DSP_SW_WORK_AROUND 0x0006 #elif (ANLG_FAM == 2) // IOTA #define C_DSP_SW_WORK_AROUND 0x000E #elif (ANLG_FAM == 3) // SYREN #define C_DSP_SW_WORK_AROUND 0x000E #endif // This workaround should be enabled only for H2-sample on full build config #if (OP_L1_STANDALONE==1) #define RAZ_VULSWITCH_REGAUDIO 0 #endif /* DSP debug trace configuration */ /*-------------------------------*/ #if (MELODY_E2) // In case of the melody E2 the DSP trace must be disable because the // melody instrument waves are overlayed with DSP trace buffer // DSP debug trace API buufer config #define C_DEBUG_BUFFER_ADD 0x17ff // Address of DSP write pointer... data are just after. #define C_DEBUG_BUFFER_SIZE 7 // Real size is incremented by 1 for DSP write pointer. // DSP debug trace type config // |<-------------- Features -------------->|<---------- Levels ----------->| // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR] #define C_DEBUG_TRACE_TYPE 0x0000 // Level = BASIC; Features = Timer + Buffer Header + Burst. #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4)) #define DSP_DEBUG_TRACE_ENABLE 1 // Enable DSP debug trace dumping capability // Currently not supported ! #endif #else // DSP debug trace API buufer config #define C_DEBUG_BUFFER_ADD 0x17ff // Address of DSP write pointer... data are just after. #define C_DEBUG_BUFFER_SIZE 2047 // Real size is incremented by 1 for DSP write pointer. // DSP debug trace type config // |<-------------- Features -------------->|<---------- Levels ----------->| // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR] #define C_DEBUG_TRACE_TYPE 0x0012 // Level = BASIC; Features = Buffer Header. #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4)) #define DSP_DEBUG_TRACE_ENABLE 1 // Enable DSP debug trace dumping capability (supported since patch 2090) #endif // AMR trace #define C_AMR_TRACE_ID 55 #endif /* d_error_status */ /*-------------------------------*/ #if ((TRACE_TYPE == 1) || (TRACE_TYPE == 4)) #define D_ERROR_STATUS_TRACE_ENABLE 1 // Enable d_error_status checking capability (supported since patch 2090) // masks to apply on d_error_status bit field for DSP patch 0x2061 or 0x2062 #define DSP_DEBUG_GSM_MASK 0x08BD #define DSP_DEBUG_GPRS_MASK 0x0f3d #endif #endif // DSP /*------------------------------------*/ /* Default value */ /*------------------------------------*/ #ifndef W_A_DSP1 #define W_A_DSP1 0 #endif #ifndef DATA14_4 #define DATA14_4 0 #endif #ifndef W_A_ITFORCE #define W_A_ITFORCE 0 #endif #ifndef W_A_DSP_IDLE3 #define W_A_DSP_IDLE3 0 #endif #ifndef L1_NEW_AEC #define L1_NEW_AEC 0 #endif #ifndef DSP_DEBUG_TRACE_ENABLE #define DSP_DEBUG_TRACE_ENABLE 0 #endif #ifndef DEBUG_DEDIC_TCH_BLOCK_STAT #define DEBUG_DEDIC_TCH_BLOCK_STAT 0 #endif #ifndef D_ERROR_STATUS_TRACE_ENABLE #define D_ERROR_STATUS_TRACE_ENABLE 0 #endif #ifndef L1_GTT #define L1_GTT 0 #define TTY_SYNC_MCU 0 #define TTY_SYNC_MCU_2 0 #define L1_GTT_FIFO_TEST_ATOMIC 0 #define NEW_WKA_PATCH 0 #define OPTIMISED 0 #endif #ifndef L1_AMR_NSYNC #define L1_AMR_NSYNC 0 #endif #ifndef FF_L1_TCH_VOCODER_CONTROL #define FF_L1_TCH_VOCODER_CONTROL 0 #define L1M_WAIT_DSP_RESTART_AFTER_VOCODER_ENABLE 0 #endif /*------------------------------------*/ /* Download */ /*------------------------------------*/ /* Possible values for the download status */ #define LEAD_READY 1 #define BLOCK_READY 2 #define PROGRAM_DONE 3 #define PAGE_SELECTION 4 /************************************/ /* Options of compilation... */ /************************************/ // Possible choice of hardware plateform. #define GEMINI 1 // GEMINI chip (rom dsp code) #define POLESTAR 2 // POLESTAR chip (no rom) // Possible choice for DSP software setup. #define NO_DWNLD 0 #define PATCH_DWNLD 1 #define DSP_DWNLD 2 #define PATCH_DSP_DWNLD 3 // MAC-S status reporting to Layer 1 #define MACS_STATUS 0 // MAC-S STATUS activated if set to 1 // Possible choice for dll_dcch_downlink interface (with FN or without FN) #define SEND_FN_TO_L2_IN_DCCH 1 /* 0=without, 1=with FN parameter */ //--------------------------------------------------------------------------------- // Neighbor Cell RXLEV indication #if ((OP_L1_STANDALONE==1) && (CODE_VERSION == NOT_SIMULATION)) #define L1_MPHC_RXLEV_IND_REPORT_SORT 1 #else #define L1_MPHC_RXLEV_IND_REPORT_SORT 0 #endif #endif /* __L1_CONFG_H__ */