FreeCalypso > hg > fc-magnetite

view src/cs/layer1/tm_include/l1tm_ver.h @ 624:012028896cfb

Find changesets by keywords (author, files, the commit message), revision number or hash, or revset expression.
FFS dev.c, Leonardo target: Fujitsu MB84VF5F5F4J2 #if 0'ed out The FFS code we got from TI/Openmoko had a stanza for "Fujitsu MB84VF5F5F4J2 stacked device", using a fake device ID code that would need to be patched manually into cfgffs.c (suppressing and overriding autodetection) and using an FFS base address in the nCS2 bank, indicating that this FFS config was probably meant for the MCP version of Leonardo which allows for 16 MiB flash with a second bank on nCS2. We previously had this FFS config stanza conditionalized under CONFIG_TARGET_LEONARDO because the base address contained therein is invalid for other targets, but now that we actually have a Leonardo build target in FC Magnetite, I realize that the better approach is to #if 0 out this stanza altogether: it is already non-functional because it uses a fake device ID code, thus it is does not add support for more Leonardo board variants, instead it is just noise.
author Mychaela Falconia <falcon@freecalypso.org>
date Sun, 22 Dec 2019 21:24:29 +0000
parents 945cf7f506b2
children
line wrap: on
line source

/************* Revision Controle System Header *************
 *                  GSM Layer 1 software 
 * L1TM_VER.H
 *
 *        Filename l1tm_ver.h
 *  Copyright 2003 (C) Texas Instruments  
 *
 ************* Revision Controle System Header *************/

/*****************************/
/* Test mode version numbers */
/*****************************/


//#define    TESTMODEVERSION  0x0300L // All previous TestMode versions pertain to
                                    // GGT Protocol version 2.0, which has been replaced
                                    // by version 3.0.

//#define    TESTMODEVERSION  0x0320L // AFC Params part of "rftw"; APCDEL intialized in "tm_init"; New fcn "l1tm_initialize_var" to switch to TestMode
                                    // Uplink-only tests loop count; RACH loop count; Dedicated mode Pass/Fail stats updated
                                    // New structure "T_TM_RETURN_ABBREV"; Continous TX/RX; New fcn "tmstats_auto_result_reset_loops";
                                    // Corrected BSIC reporting problem; Power skip fcn implemented ("rftw/rftr 16"); A-F Loopback modes supported;
                                    // Chan. monitoring while in dedic. mode possible; FB26/D_BAMS_MEAS tasks enabled only with chan. monitoring;
                                    // New fcn "tmstats_mon_confirm"; RF struct incorporates new TX descriptor table;
                                    // AGC includes lna_off bit (least-significant bit); agc_, afc_ & adc_enable part of l1_config struct;
                                    // Variable number of guard bits in "l1tm_fill_burst"......
//#define    TESTMODEVERSION  0x0321L // Implemented FRAME_NUMBER in l1tm_stats_read(). Timing advance takes effect immediately. stats_read reports 16 or 32 bit values only.
                                    // Only one uplink message sent. Some indices in l1tm_version_get implemented. AGC gain and lna_off set only once to save instruction cycles.
                                    // Cleaned up enums in l1_tm_types.h. Removed case STANDARD from rf_param_read. 
                                    // Updated all argument types of testmode functions according to TM100 v3.2.1. Changed mem_read to support reception of page and 
                                    // register values in one 16-bit value from PCTM.  mem_read can read up to 124 bytes. Changed the TestMode primitive structure to include
                                    // only 2 generic ones plus mem_write and mem_read.

//#define    TESTMODEVERSION  0x0400L // REQ991:
                                    // - SIMULATION for test mode => new non-regression flow regress_tm.bat
                                    // - Rework of test mode state machines to make them independent from each other
                                    // - Rework of simulated upper layers (L3,CST) to be able to run L1 scenarios with TESTMODE=3
                                    // Correction of BUG989, BUG990, BUG992

//#define    TESTMODEVERSION  0x0401L // Merge with TM version 0x321

//#define    TESTMODEVERSION  0x0402L // TM rework PART II
//#define    TESTMODEVERSION  0x0403L // Alignment with TM100 v.3.5.0
                                    // Implementation of new functionality: single PM on monitor channel (rfe 15)
//#define    TESTMODEVERSION  0x0404L // Closed REQ01129: Implementation of GPRS test mode
//#define    TESTMODEVERSION  0x0405L // Alignment with SSA 5.3.3, 
                                      // Correction of BUG2048, BUG2050, BUG2294, BUG2295
#define    TESTMODEVERSION  0x0406L   // REQ03410


//#define    TMAPIVERSION     0x0350L  // New: TM API version (TM100 version number)
//#define    TMAPIVERSION     0x0360L  // TM100 change for GPRS test mode
//#define    TMAPIVERSION     0x0361L  // tm patch 361 for SW version 520
//#define    TMAPIVERSION     0x0362L  // tm patch 362 for SW version 531
#define    TMAPIVERSION     0x0370L  // Multi-band support