FreeCalypso > hg > fc-magnetite
view src/cs/drivers/drv_core/uart/serialswitch_core.c @ 317:07818fb33771
ABB_Read_Status() put under ABB_SEMAPHORE_PROTECTION
(all targets, all configs)
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Wed, 29 Nov 2017 08:10:15 +0000 |
parents | 945cf7f506b2 |
children |
line wrap: on
line source
/******************************************************************************* * * SERIALSWITCH_CORE.C * * This module allows managing the use of the serial ports of TI GSM Evaluation * Boards. * An application may have to send several serial data flows. The board on which * the application is running may have one or several devices. The purpose of * this module is to establish connections between the serial data flows and the * serial devices at runtime, when the application is started. * * (C) Texas Instruments 1999 - 2003 * ******************************************************************************/ /* * 17/12/03 * Duplication of serialswitch.c for L1 standalone only * ******************************************************************************/ #define __SERIALSWITCH_CORE_C__ #define __STANDARD_H__ /* Avoid to define UBYTE, SYS_UWORD16 and UINT32. */ #include "l1sw.cfg" #include "chipset.cfg" #if (OP_L1_STANDALONE == 0) #include "main/sys_types.h" #else #include "sys_types.h" #endif #include "nucleus.h" #include "traceswitch.h" #include "serialswitch_core.h" #include "uart/uart.h" #include "memif/mem.h" #define DUMMY_DEVICE (0) #define IIR (0x02) /* UART interrupt ident. register - Read only */ #define SCR (0x10) /* UART suppl. control register - Read/Write */ #define SSR (0x11) /* UART suppl. status register - Read only */ /* * Interrupt identification register. * Bit 0 is set to 0 if an IT is pending. * Bits 1 and 2 are used to identify the IT. */ #define IIR_BITS_USED (0x07) #define IT_NOT_PENDING (0x01) /* * Supplementary Control Register */ #define RX_CTS_WAKE_UP_ENABLE_BIT (4) /* * Supplementary Status Register */ #define RX_CTS_WAKE_UP_STS (0x02) /* Wake-up interrupt occurred */ /* * This macro allows to read an UART register. */ #define READ_UART_REGISTER(UART,REG) \ *((volatile SYS_UWORD8 *) ((UART)->base_address + (REG))) /* * This macro allows to disable the UART's wake-up interrupt. */ #define DISABLE_WAKE_UP_INTERRUPT(UART) \ *((volatile SYS_UWORD8 *) ((UART)->base_address + SCR)) &= \ ~(1 << (RX_CTS_WAKE_UP_ENABLE_BIT)); /* * Wake-up time duration in seconds and in number of TDMAs. * 1 TDMA = (6 / 1300) s = 0.004615 s (= 4.615 ms). */ #define WAKE_UP_TIME_DURATION (10) /* 10 seconds */ #define WAKE_UP_TIME_IN_TDMA (WAKE_UP_TIME_DURATION * 1300 / 6) /* * Global uartswitch variable as read from FFS. * It is supposed that NUMBER_OF_TR_UART, NUMBER_OF_FD_UART * and NUMBER_OF_BT_UART have the same values. */ #define DUMMY ('0') #define G23_PANEL ('G') #define RIVIERA_TRACE_MUX ('R') #define FD_AT_COMMAND ('D') #define BLUETOOTH_HCI ('B') #if (CHIPSET == 12) char ser_cfg_info[NUMBER_OF_TR_UART] = {DUMMY, DUMMY, DUMMY}; #else char ser_cfg_info[NUMBER_OF_TR_UART] = {DUMMY, DUMMY}; #endif static SYS_UWORD16 serial_cfg = 0x0048; /* All dummies */ /* * Types of flows supported. */ typedef enum { TRACE_FLOW #if (OP_L1_STANDALONE == 0) , FAX_DATA_FLOW, BLUETOOTH_HCI_FLOW #endif } t_flow_type; /* * For each serial data flow, a set of function pointers allows calling the * functions associated to a serial device. */ typedef struct s_tr_functions { T_tr_UartId device; void (*tr_Init) (T_tr_UartId device, T_tr_Baudrate baudrate, void (callback_function (void))); SYS_UWORD32 (*tr_ReadNChars) (T_tr_UartId device, char *buffer, SYS_UWORD32 chars_to_read); SYS_UWORD32 (*tr_ReadNBytes) (T_tr_UartId device, char *buffer, SYS_UWORD32 chars_to_read, SYS_BOOL *eof_detected); SYS_UWORD32 (*tr_WriteNChars) (T_tr_UartId device, char *buffer, SYS_UWORD32 chars_to_write); SYS_UWORD32 (*tr_EncapsulateNChars) (T_tr_UartId device, char *buffer, SYS_UWORD32 chars_to_write); SYS_UWORD32 (*tr_WriteNBytes) (T_tr_UartId device, SYS_UWORD8 *buffer, SYS_UWORD32 chars_to_write); void (*tr_WriteChar) (T_tr_UartId device, char character); void (*tr_WriteString) (T_tr_UartId device, char *buffer); SYS_BOOL (*tr_EnterSleep) (T_tr_UartId device); void (*tr_WakeUp) (T_tr_UartId device); } t_tr_functions; /* * Prototypes of dummy functions. * Dummy functions for Trace. */ static void dummy_tr_Init (T_tr_UartId device, T_tr_Baudrate baudrate, void (callback_function (void))); static SYS_UWORD32 dummy_tr_ReadNChars (T_tr_UartId device, char *buffer, SYS_UWORD32 chars_to_read); static SYS_UWORD32 dummy_tr_ReadNBytes (T_tr_UartId device, char *buffer, SYS_UWORD32 chars_to_read, SYS_BOOL *eof_detected); static SYS_UWORD32 dummy_tr_WriteNChars (T_tr_UartId device, char *buffer, SYS_UWORD32 chars_to_write); static SYS_UWORD32 dummy_tr_EncapsulateNChars (T_tr_UartId device, char *buffer, SYS_UWORD32 chars_to_write); static SYS_UWORD32 dummy_tr_WriteNBytes (T_tr_UartId device, SYS_UWORD8 *buffer, SYS_UWORD32 chars_to_write); static void dummy_tr_WriteChar (T_tr_UartId device, char character); static void dummy_tr_WriteString (T_tr_UartId device, char *buffer); static SYS_BOOL dummy_tr_EnterSleep (T_tr_UartId device); static void dummy_tr_WakeUp (T_tr_UartId device); /* * Constants tables representing the various possible configurations * for Trace, Fax & Data and Bluetooth HCI according to the different devices. * Constant table for Trace using no device. */ static const t_tr_functions dummy_trace = { (T_tr_UartId) DUMMY_DEVICE, dummy_tr_Init, dummy_tr_ReadNChars, dummy_tr_ReadNBytes, dummy_tr_WriteNChars, dummy_tr_EncapsulateNChars, dummy_tr_WriteNBytes, dummy_tr_WriteChar, dummy_tr_WriteString, dummy_tr_EnterSleep, dummy_tr_WakeUp }; /* * Constant table for Trace using UART IrDA. */ static const t_tr_functions uart_irda_trace = { UA_UART_0, UA_Init, UA_ReadNChars, UA_ReadNBytes, UA_WriteNChars, UA_EncapsulateNChars, UA_WriteNBytes, UA_WriteChar, UA_WriteString, UA_EnterSleep, UA_WakeUp }; /* * Constant table for Trace using UART Modem. */ static const t_tr_functions uart_modem_trace = { UA_UART_1, UA_Init, UA_ReadNChars, UA_ReadNBytes, UA_WriteNChars, UA_EncapsulateNChars, UA_WriteNBytes, UA_WriteChar, UA_WriteString, UA_EnterSleep, UA_WakeUp }; #if (CHIPSET == 12) /* * Constant table for Trace using UART Modem2. */ static const t_tr_functions uart_modem2_trace = { UA_UART_2, UA_Init, UA_ReadNChars, UA_ReadNBytes, UA_WriteNChars, UA_EncapsulateNChars, UA_WriteNBytes, UA_WriteChar, UA_WriteString, UA_EnterSleep, UA_WakeUp }; #endif /* * UART structure used for UARTs. */ typedef struct s_uart { SYS_UWORD32 base_address; SYS_BOOL device_used; SYS_BOOL deep_sleep_set_up; t_flow_type flow_type; SYS_WORD16 flow_id; void (*interrupt_handler) (int uart_id, SYS_UWORD8 interrupt_status); } t_uart; static const t_tr_functions *tr_functions[SER_MAX_NUMBER_OF_FLOWS]; /* * Timer used for duration control when UARTs are waked up by an interrupt or * each time any new incoming characters are received; This timer prevents the * system to enter deep sleep mode. */ static NU_TIMER uart_sleep_timer; SYS_BOOL uart_sleep_timer_enabled; /* * HISR used to reset and restart the sleep timer from an UART use by a Trace * flow in case of incoming characters. */ #define TIMER_HISR_PRIORITY (2) #define TIMER_HISR_STACK_SIZE (512) /* Bytes. */ static NU_HISR timer_hisr_ctrl_block; static char timer_hisr_stack[TIMER_HISR_STACK_SIZE]; /* * For next arrays, it is supposed that NUMBER_OF_TR_UART, NUMBER_OF_FD_UART * and NUMBER_OF_BT_UART have the same values. * An index on an internal uart for trace, fax & data or bluetooth hci reffers * to the same uart device. */ static t_uart int_uart[NUMBER_OF_TR_UART]; #if ((CHIPSET == 2) || (CHIPSET == 3)) static SYS_UWORD32 uart_spurious_interrupts; #elif ((CHIPSET == 4) || (CHIPSET == 5) || (CHIPSET == 6) || (CHIPSET == 7) || (CHIPSET == 8) || (CHIPSET == 9) || (CHIPSET == 10) || (CHIPSET == 11) || (CHIPSET == 12)) static SYS_UWORD32 uart_modem_spurious_interrupts; static SYS_UWORD32 uart_irda_spurious_interrupts; #endif #if (CHIPSET == 12) static SYS_UWORD32 uart_modem2_spurious_interrupts; #endif static const SYS_UWORD32 uart_base_address[NUMBER_OF_TR_UART] = { MEM_UART_IRDA, MEM_UART_MODEM #if (CHIPSET == 12) , MEM_UART_MODEM2 #endif }; /******************************************************************************* * * dummy_tr_Init * * Purpose: No action. * * Parameters: See SER_tr_Init. * * Return: none * ******************************************************************************/ static void dummy_tr_Init (T_tr_UartId device, T_tr_Baudrate baudrate, void (callback_function (void))) { /* * No action. */ } /******************************************************************************* * * dummy_tr_ReadNChars * * Purpose: No action. * * Parameters: See SER_tr_ReadNChars. * * Return: 0 * ******************************************************************************/ static SYS_UWORD32 dummy_tr_ReadNChars (T_tr_UartId device, char *buffer, SYS_UWORD32 chars_to_read) { return (0); } /******************************************************************************* * * dummy_tr_ReadNBytes * * Purpose: No action. * * Parameters: See SER_tr_ReadNBytes. * * Return: 0 * ******************************************************************************/ static SYS_UWORD32 dummy_tr_ReadNBytes (T_tr_UartId device, char *buffer, SYS_UWORD32 chars_to_read, SYS_BOOL *eof_detected) { return (0); } /******************************************************************************* * * dummy_tr_WriteNChars * * Purpose: No action. * * Parameters: See SER_tr_WriteNChars. * * Return: The number of character to write. * ******************************************************************************/ static SYS_UWORD32 dummy_tr_WriteNChars (T_tr_UartId device, char *buffer, SYS_UWORD32 chars_to_write) { return (chars_to_write); } /******************************************************************************* * * dummy_tr_EncapsulateNChars * * Purpose: No action. * * Parameters: See SER_tr_EncapsulateNChars. * * Return: The number of character to write. * ******************************************************************************/ static SYS_UWORD32 dummy_tr_EncapsulateNChars (T_tr_UartId device, char *buffer, SYS_UWORD32 chars_to_write) { return (chars_to_write); } /******************************************************************************* * * dummy_tr_WriteNBytes * * Purpose: No action. * * Parameters: See SER_tr_WriteNBytes. * * Return: The number of byte to write. * ******************************************************************************/ static SYS_UWORD32 dummy_tr_WriteNBytes (T_tr_UartId device, SYS_UWORD8 *buffer, SYS_UWORD32 chars_to_write) { return (chars_to_write); } /******************************************************************************* * * dummy_tr_WriteChar * * Purpose: No action. * * Parameters: See SER_tr_WriteChar. * * Return: none * ******************************************************************************/ static void dummy_tr_WriteChar (T_tr_UartId device, char character) { /* * No action. */ } /******************************************************************************* * * dummy_tr_WriteString * * Purpose: No action. * * Parameters: See SER_tr_WriteString. * * Return: none * ******************************************************************************/ static void dummy_tr_WriteString (T_tr_UartId device, char *buffer) { /* * No action. */ } /******************************************************************************* * * dummy_tr_EnterSleep * * Purpose: No action. * * Parameters: See SER_tr_EnterSleep. * * Return: 1 * ******************************************************************************/ static SYS_BOOL dummy_tr_EnterSleep (T_tr_UartId device) { return (1); } /******************************************************************************* * * dummy_tr_WakeUp * * Purpose: No action. * * Parameters: See SER_tr_WakeUp. * * Return: none * ******************************************************************************/ static void dummy_tr_WakeUp (T_tr_UartId device) { /* * No action. */ } /******************************************************************************* * * analyze_uart_sleep_timer_expiration * * Purpose : The timer has just expired. If requested, UARTs can again be set * up to enter Deep Sleep. * * Arguments: In : id: parameter not used. * Out: none * * Returns : none * ******************************************************************************/ static VOID analyze_uart_sleep_timer_expiration (UNSIGNED id) { /* * Timer has expired. * UARTs can again be set up for Deep Sleep. */ (void) NU_Control_Timer (&uart_sleep_timer, NU_DISABLE_TIMER); uart_sleep_timer_enabled = 0; } /******************************************************************************* * * start_uart_sleep_timer * * Purpose : Starts the sleep timer once UARTs have been waked-up by an * interrupt or if new incoming characters have been received. * * Arguments: In : none * Out: none * * Returns : none * ******************************************************************************/ static void start_uart_sleep_timer (void) { /* * UART sleep timer is started. * UARTs can't no more be set up for Deep Sleep until the timer expires. */ (void) NU_Reset_Timer (&uart_sleep_timer, &analyze_uart_sleep_timer_expiration, WAKE_UP_TIME_IN_TDMA, 0, /* The timer expires once. */ NU_DISABLE_TIMER); (void) NU_Control_Timer (&uart_sleep_timer, NU_ENABLE_TIMER); } /******************************************************************************* * * set_flow_functions * * Purpose: Initializes a serial data flow functions set with the set of * functions of the selected device. * * Parameters: In : flow : index of the serial data flow * serial_driver: allows knowing which set of functions must * be selected * Out: none * * Return: none * ******************************************************************************/ static void set_flow_functions (int flow, T_SerialDriver serial_driver) { switch (serial_driver) { case UART_IRDA_TRACE: case UART_MODEM_TRACE: #if (CHIPSET == 12) case UART_MODEM2_TRACE: #endif if (serial_driver == UART_IRDA_TRACE) tr_functions[flow] = &uart_irda_trace; else { #if (CHIPSET == 12) if (serial_driver == UART_MODEM2_TRACE) tr_functions[flow] = &uart_modem2_trace; else #endif tr_functions[flow] = &uart_modem_trace; } int_uart[tr_functions[flow]->device].device_used = 1; int_uart[tr_functions[flow]->device].flow_type = TRACE_FLOW; int_uart[tr_functions[flow]->device].flow_id = flow; int_uart[tr_functions[flow]->device].interrupt_handler = UA_InterruptHandler; break; case DUMMY_TRACE: tr_functions[flow] = &dummy_trace; break; } } /******************************************************************************* * * SER_InitSerialConfig * * Purpose: The parameter serial_info allows knowing all serial information * necessary to set up the serial configuration of an application. * From this information, the function is able to determine if the * current serial configuration read out from the flash memory is * valid. If it does not correspond to an allowed configuration, the * default configuration is selected. This function must be called at * the application's initialization, but never after. * * Parameters: In : serial_info: application serial information like the default * configuration and all allowed configurations. * Out: none * * Return: none * ******************************************************************************/ void SER_InitSerialConfig (T_AppliSerialInfo *serial_info) { int uart_id; int flow; T_SerialDriver serial_driver; SYS_UWORD16 *allowed_config; SYS_UWORD8 nb_allowed_config; SYS_BOOL valid_config_selected; SYS_BOOL uart_used; SYS_BOOL uart_used_for_trace; SYS_UWORD16 current_config; SYS_UWORD16 *pt_current_config = &(current_config); /* * Basic UARTs initializations. */ for (uart_id = 0; uart_id < NUMBER_OF_TR_UART; uart_id++) { int_uart[uart_id].base_address = uart_base_address[uart_id]; int_uart[uart_id].device_used = 0; int_uart[uart_id].deep_sleep_set_up = 0; } #if ((CHIPSET == 2) || (CHIPSET == 3)) uart_spurious_interrupts = 0; #elif ((CHIPSET == 4) || (CHIPSET == 5) || (CHIPSET == 6) || (CHIPSET == 7) || (CHIPSET == 8) || (CHIPSET == 9) || (CHIPSET == 10) || (CHIPSET == 11) || (CHIPSET == 12)) uart_modem_spurious_interrupts = 0; uart_irda_spurious_interrupts = 0; #endif #if (CHIPSET == 12) uart_modem2_spurious_interrupts = 0; #endif uart_sleep_timer_enabled = 0; /* * Compute the current serial configuration. */ for (uart_id = 0; uart_id < NUMBER_OF_TR_UART; uart_id++) { switch (ser_cfg_info[uart_id]) { case G23_PANEL: serial_cfg = serial_cfg + ((uart_id + 1) << (12 - (4 * SER_PROTOCOL_STACK))); break; case RIVIERA_TRACE_MUX: serial_cfg = serial_cfg + ((uart_id + 1) << (12 - (4 * SER_LAYER_1))); break; case FD_AT_COMMAND: serial_cfg = serial_cfg + ((uart_id + 1) << (12 - (4 * SER_FAX_DATA))); break; case BLUETOOTH_HCI: serial_cfg = serial_cfg + ((uart_id + 1) << (12 - (4 * SER_BLUETOOTH_HCI))); break; case DUMMY: break; } } current_config = serial_cfg; valid_config_selected = 0; nb_allowed_config = serial_info->num_config; /* * Checks if the current serial config is one of the allowed. */ while ((nb_allowed_config > 0) && !valid_config_selected) { nb_allowed_config--; allowed_config = (SYS_UWORD16 *) &(serial_info->allowed_config[nb_allowed_config]); if (*pt_current_config == *allowed_config) valid_config_selected = 1; } /* * If not, the default configuration is selected. */ if (!valid_config_selected) { pt_current_config = (SYS_UWORD16 *)&(serial_info->default_config); } /* * The serial data flow functions set is initialized. */ flow = 0; while (flow < SER_MAX_NUMBER_OF_FLOWS) { serial_driver = (T_SerialDriver) (((*pt_current_config) >> (12 - flow * 4)) & 0x000F); set_flow_functions (flow, serial_driver); flow++; } /* * Checks if both UARTs are used. * If not, performs minimum initialization including Sleep Mode. * Checks also if at least one UART is used by a Trace flow. * If so, create a HISR in order to reset and restart the sleep timer * in case of incoming characters. */ uart_used = 0; uart_used_for_trace = 0; for (uart_id = 0; uart_id < NUMBER_OF_TR_UART; uart_id++) { if (!(int_uart[uart_id].device_used)) initialize_uart_sleep ((T_tr_UartId) uart_id); else { /* if (int_uart[uart_id].device_used) */ uart_used = 1; /* At least one UART is used */ if (int_uart[uart_id].flow_type == TRACE_FLOW) { /* At least one UART used by a Trace flow */ uart_used_for_trace = 1; } } } /* * If at least one uart is used, create a timer to figure out if the system * can enter deep sleep mode regarding the UARTs. */ if (uart_used) { (void) NU_Create_Timer ( &uart_sleep_timer, "Sleep", &analyze_uart_sleep_timer_expiration, 0, /* Parameter supplied to the routine: not used. */ WAKE_UP_TIME_IN_TDMA, 0, /* The timer expires once. */ NU_DISABLE_TIMER); /* * If at least one uart is used by a Trace flow, create a HISR to reset * and restart the sleep timer. */ if (uart_used_for_trace) { /* * The HISR entry function is the same function than the one called * by the Rx HISR of the UARTFAX, since the only aim is to reset * and restart the sleep timer in case of incoming characters on * the Trace UART. */ (void) NU_Create_HISR ( &timer_hisr_ctrl_block, "Tim_HISR", SER_restart_uart_sleep_timer, TIMER_HISR_PRIORITY, &(timer_hisr_stack[0]), TIMER_HISR_STACK_SIZE); } } } /******************************************************************************* * * All functions SER_tr_xxx and SER_fd_xxx call a function of the UART trace * driver or the UART fax & data driver. * All functions SER_bt_xxx call a function of the UART Bluetooth HCI driver. * See the function call for parameters and return values. * ******************************************************************************/ void SER_tr_Init (int serial_data_flow, T_tr_Baudrate baudrate, void (callback_function (void))) { tr_functions[serial_data_flow]->tr_Init ( tr_functions[serial_data_flow]->device, baudrate, callback_function); } SYS_UWORD32 SER_tr_ReadNChars (int serial_data_flow, char *buffer, SYS_UWORD32 chars_to_read) { return (tr_functions[serial_data_flow]->tr_ReadNChars ( tr_functions[serial_data_flow]->device, buffer, chars_to_read)); } SYS_UWORD32 SER_tr_ReadNBytes (int serial_data_flow, char *buffer, SYS_UWORD32 chars_to_read, SYS_BOOL *eof_detected) { return (tr_functions[serial_data_flow]->tr_ReadNBytes ( tr_functions[serial_data_flow]->device, buffer, chars_to_read, eof_detected)); } SYS_UWORD32 SER_tr_WriteNChars (int serial_data_flow, char *buffer, SYS_UWORD32 chars_to_write) { return (tr_functions[serial_data_flow]->tr_WriteNChars ( tr_functions[serial_data_flow]->device, buffer, chars_to_write)); } SYS_UWORD32 SER_tr_EncapsulateNChars (int serial_data_flow, char *buffer, SYS_UWORD32 chars_to_write) { return (tr_functions[serial_data_flow]->tr_EncapsulateNChars ( tr_functions[serial_data_flow]->device, buffer, chars_to_write)); } SYS_UWORD32 SER_tr_WriteNBytes (int serial_data_flow, SYS_UWORD8 *buffer, SYS_UWORD32 chars_to_write) { return (tr_functions[serial_data_flow]->tr_WriteNBytes ( tr_functions[serial_data_flow]->device, buffer, chars_to_write)); } void SER_tr_WriteChar (int serial_data_flow, char character) { tr_functions[serial_data_flow]->tr_WriteChar ( tr_functions[serial_data_flow]->device, character); } void SER_tr_WriteString (int serial_data_flow, char *buffer) { tr_functions[serial_data_flow]->tr_WriteString ( tr_functions[serial_data_flow]->device, buffer); } SYS_BOOL SER_tr_EnterSleep (int serial_data_flow) { return (tr_functions[serial_data_flow]->tr_EnterSleep ( tr_functions[serial_data_flow]->device)); } void SER_tr_WakeUp (int serial_data_flow) { tr_functions[serial_data_flow]->tr_WakeUp ( tr_functions[serial_data_flow]->device); } /******************************************************************************* * * SER_UartSleepStatus * * Purpose: This function checks if both UARTs are ready to enter Deep Sleep. * * Parameters: In : none * Out: none * * Return: 0 : Deep Sleep is not possible. * >= 1 : Deep Sleep is possible. * ******************************************************************************/ SYS_BOOL SER_UartSleepStatus (void) { t_uart *uart; int uart_id; SYS_BOOL status; /* * Check first if the sleep timer is active or if a Dynamic Switch is * being processed. A return is used to simplify the code. */ if (uart_sleep_timer_enabled) return (0); /* * Check if both UARTs are ready to enter Deep Sleep. */ status = 1; uart_id = 0; while ((uart_id < NUMBER_OF_TR_UART) && (status)) { uart = &(int_uart[uart_id]); /* * Check if the specified UART is actually used. */ if (uart->device_used) { /* * Check if the specified UART is used by a Trace or * by a Fax & Data flow. */ if (uart->flow_type == TRACE_FLOW) status = SER_tr_EnterSleep (uart->flow_id); else status = 0; if (status) { /* * The specified UART is now set up for Deep Sleep. */ uart->deep_sleep_set_up = 1; } } uart_id++; } /* * Check if Deep Sleep is finally possible. * If not revert eventual Deep Sleep settings. */ if (!status) { for (uart_id = 0; uart_id < NUMBER_OF_TR_UART; uart_id++) { uart = &(int_uart[uart_id]); /* * If the specified used UART has already been set up for * Deep Sleep, revert these settings. */ if ((uart->device_used) && (uart->deep_sleep_set_up)) { /* * Check if the specified UART is used by a Trace or * by a Fax & Data flow. * Bluetooth HCI can not yet handled Deep Sleep Mode. */ if (uart->flow_type == TRACE_FLOW) SER_tr_WakeUp (uart->flow_id); uart->deep_sleep_set_up = 0; } } } return (status); } /******************************************************************************* * * SER_WakeUpUarts * * Purpose: This function wakes up used UARTs after Deep Sleep. * * Parameters: In : none * Out: none * * Return: none * ******************************************************************************/ void SER_WakeUpUarts (void) { t_uart *uart; int uart_id; if (uart_sleep_timer_enabled) start_uart_sleep_timer (); for (uart_id = 0; uart_id < NUMBER_OF_TR_UART; uart_id++) { uart = &(int_uart[uart_id]); /* * Check if the specified UART is actually used, and has not yet * been waked up. */ if ((uart->device_used) && (uart->deep_sleep_set_up)) { /* * Check if the specified UART is used by a Trace or * by a Fax & Data flow. * Bluetooth HCI can not yet handled Deep Sleep Mode. */ if (uart->flow_type == TRACE_FLOW) SER_tr_WakeUp (uart->flow_id); /* * The specified UART is no more set up for Deep Sleep. */ uart->deep_sleep_set_up = 0; } } } /******************************************************************************* * * SER_restart_uart_sleep_timer * * Purpose : Resets and restarts the sleep timer each time some characters are * received. * * Arguments: In : none * Out: none * * Returns : none * ******************************************************************************/ void SER_restart_uart_sleep_timer (void) { /* * First disable the timer. */ (void) NU_Control_Timer (&uart_sleep_timer, NU_DISABLE_TIMER); /* * Then start again this timer for a new period. */ start_uart_sleep_timer (); } /******************************************************************************* * * SER_activate_timer_hisr * * Purpose : Activates the timer HISR to reset and restart the sleep timer * each time some characters are received. * * Arguments: In : none * Out: none * * Returns : none * ******************************************************************************/ void SER_activate_timer_hisr (void) { (void) NU_Activate_HISR (&timer_hisr_ctrl_block); } #if ((CHIPSET == 2) || (CHIPSET == 3)) /******************************************************************************* * * SER_uart_handler * * Purpose : UART interrupt handler. * * Arguments: In : none * Out: none * * Returns : none * ******************************************************************************/ void SER_uart_handler (void) { SYS_UWORD8 interrupt_status; t_uart *uart; int uart_id; SYS_BOOL it_identified; it_identified = 0; /* * Check first for a wake-up interrupt. */ uart_id = 0; while ((uart_id < NUMBER_OF_TR_UART) && (!it_identified)) { uart = &(int_uart[uart_id]); interrupt_status = READ_UART_REGISTER (uart, SSR); if (interrupt_status & RX_CTS_WAKE_UP_STS) { /* Wake-up IT has occurred */ it_identified = 1; uart_sleep_timer_enabled = 1; DISABLE_WAKE_UP_INTERRUPT (uart); } uart_id++; } /* * If no wake-up interrupt has been detected, check then systematically * both UARTs for other interrupt causes. */ if (!it_identified) { for (uart_id = 0; uart_id < NUMBER_OF_TR_UART; uart_id++) { uart = &(int_uart[uart_id]); interrupt_status = READ_UART_REGISTER (uart, IIR) & IIR_BITS_USED; if (!(interrupt_status & IT_NOT_PENDING)) { it_identified = 1; (*(uart->interrupt_handler)) (uart_id, interrupt_status); } else { if ((uart_id == UA_UART_1) && (!it_identified)) uart_spurious_interrupts++; } } } } #elif ((CHIPSET == 4) || (CHIPSET == 5) || (CHIPSET == 6) || (CHIPSET == 7) || (CHIPSET == 8) || (CHIPSET == 9) || (CHIPSET == 10) || (CHIPSET == 11) || (CHIPSET == 12)) /******************************************************************************* * * SER_uart_modem_handler * * Purpose : UART MODEM interrupt handler. * * Arguments: In : none * Out: none * * Returns : none * ******************************************************************************/ void SER_uart_modem_handler (void) { SYS_UWORD8 interrupt_status; t_uart *uart; SYS_BOOL it_wakeup_identified; it_wakeup_identified = 0; uart = &(int_uart[UA_UART_1]); /* * Check first for a wake-up interrupt. */ interrupt_status = READ_UART_REGISTER (uart, SSR); if (interrupt_status & RX_CTS_WAKE_UP_STS) { /* Wake-up IT has occurred */ it_wakeup_identified = 1; uart_sleep_timer_enabled = 1; DISABLE_WAKE_UP_INTERRUPT (uart); } /* * If no wake-up interrupt has been detected, check UART for other * interrupt causes. */ if (!it_wakeup_identified) { interrupt_status = READ_UART_REGISTER (uart, IIR) & IIR_BITS_USED; if (!(interrupt_status & IT_NOT_PENDING)) (*(uart->interrupt_handler)) (UA_UART_1, interrupt_status); else uart_modem_spurious_interrupts++; } } /******************************************************************************* * * SER_uart_irda_handler * * Purpose : UART IrDA interrupt handler. * * Arguments: In : none * Out: none * * Returns : none * ******************************************************************************/ void SER_uart_irda_handler (void) { SYS_UWORD8 interrupt_status; t_uart *uart; SYS_BOOL it_wakeup_identified; it_wakeup_identified = 0; uart = &(int_uart[UA_UART_0]); /* * Check first for a wake-up interrupt. */ interrupt_status = READ_UART_REGISTER (uart, SSR); if (interrupt_status & RX_CTS_WAKE_UP_STS) { /* Wake-up IT has occurred */ it_wakeup_identified = 1; uart_sleep_timer_enabled = 1; DISABLE_WAKE_UP_INTERRUPT (uart); } /* * If no wake-up interrupt has been detected, check UART for other * interrupt causes. */ if (!it_wakeup_identified) { interrupt_status = READ_UART_REGISTER (uart, IIR) & IIR_BITS_USED; if (!(interrupt_status & IT_NOT_PENDING)) (*(uart->interrupt_handler)) (UA_UART_0, interrupt_status); else uart_irda_spurious_interrupts++; } } #endif #if (CHIPSET == 12) /******************************************************************************* * * SER_uart_modem2_handler * * Purpose : UART IrDA interrupt handler. * * Arguments: In : none * Out: none * * Returns : none * ******************************************************************************/ void SER_uart_modem2_handler (void) { SYS_UWORD8 interrupt_status; t_uart *uart; SYS_BOOL it_wakeup_identified; it_wakeup_identified = 0; uart = &(int_uart[UA_UART_2]); /* * Check first for a wake-up interrupt. */ interrupt_status = READ_UART_REGISTER (uart, SSR); if (interrupt_status & RX_CTS_WAKE_UP_STS) { /* Wake-up IT has occurred */ it_wakeup_identified = 1; uart_sleep_timer_enabled = 1; DISABLE_WAKE_UP_INTERRUPT (uart); } /* * If no wake-up interrupt has been detected, check UART for other * interrupt causes. */ if (!it_wakeup_identified) { interrupt_status = READ_UART_REGISTER (uart, IIR) & IIR_BITS_USED; if (!(interrupt_status & IT_NOT_PENDING)) (*(uart->interrupt_handler)) (UA_UART_2, interrupt_status); else uart_modem2_spurious_interrupts++; } } #endif /* * Temporary functions. */ void UT_Init (int device_id, T_tr_Baudrate baudrate, void (callback_function (void))) { SER_tr_Init (SER_PROTOCOL_STACK, baudrate, callback_function); } SYS_UWORD32 UT_ReadNChars (int device_id, char *buffer, SYS_UWORD32 chars_to_read) { return (SER_tr_ReadNChars (SER_PROTOCOL_STACK, buffer, chars_to_read)); } SYS_UWORD32 UT_WriteNChars (int device_id, char *buffer, SYS_UWORD32 chars_to_write) { return (SER_tr_WriteNChars (SER_PROTOCOL_STACK, buffer, chars_to_write)); } void UT_WriteChar (int device_id, char character) { SER_tr_WriteChar (SER_PROTOCOL_STACK, character); } void UT_WriteString (int device_id, char *buffer) { SER_tr_WriteString (SER_PROTOCOL_STACK, buffer); }