FreeCalypso > hg > fc-magnetite
view src/g23m-gsm/rr/cus_rr.h @ 605:07d0dc4431f4
bootloader.s: same MEMIF fix as in int.s plus DPLL BYPASS fix
Both MEMIF and DPLL settings are now the same between int.s and bootloader.s
assembly code paths. Previously bootloader.s was setting DPLL BYPASS /2 mode,
which persisted until _INT_Initialize code with the bootloader body omitted,
or was changed to /1 in the hardware init function in the
bootloader.lib:start.obj module.
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Mon, 17 Jun 2019 18:40:32 +0000 |
parents | 27a4235405c6 |
children |
line wrap: on
line source
/* +----------------------------------------------------------------------------- | Project : | Modul : +----------------------------------------------------------------------------- | Copyright 2002 Texas Instruments Berlin, AG | All rights reserved. | | This file is confidential and a trade secret of Texas | Instruments Berlin, AG | The receipt of or possession of this file does not convey | any rights to reproduce or disclose its contents or to | manufacture, use, or sell anything it may describe, in | whole, or in part, without the specific written consent of | Texas Instruments Berlin, AG. +----------------------------------------------------------------------------- | Purpose : Custom dependent definitions for RR of the | mobile station +----------------------------------------------------------------------------- */ #ifndef CUS_RR_H #define CUS_RR_H /*==== CONSTANTS ==================================================*/ /* * TIMER_VALUES * * Description : The constants define the timer values * for the RR timer TXXX depending on the various * channel types and service access point identifiers. * If your target system uses other units please * change the values. */ /* * all values in milliseconds independent from the target */ #define TRESELECT_VALUE 10000 #define TABORT_VALUE 10000 #define T3110_VALUE 500 #define T3110_SDCCH_VALUE 900 #define T3126_VALUE 2500 #define T3122_VALUE(a) (1000*(a)) #define T_PLMN_SEARCH_VALUE 60000 /* CSI-LLD section:4.1.3.2 * Search mode timer values in seconds */ #define TFAST_CS_VALUE 240000 #define TNORMAL_CS_VALUE 240000 #define ONE_SEC 1000 #define TEN_SEC 10000 #define TWENTY_SEC 20000 #define THIRTY_SEC 30000 #define SIXTY_SEC 60000 #define TWO_MIN 120000 #define SIX_MIN 360000 #ifdef TI_PS_FF_AT_P_CMD_CTREG #define T_TEN_SEC 1 #define T_TWENTY_SEC 2 #define T_THIRTY_SEC 3 #define T_SIXTY_SEC 6 #define T_TWO_MIN 12 #define T_SIX_MIN 36 #endif /* TI_PS_FF_AT_P_CMD_CTREG */ /* * TIMER IDENTIFIER * * Description : The constants define the identifier of the * timer resources of RR. */ #define FOUR_FRAMES 4 #define T3110_NAME "T3110" #define T3122_NAME "T3122" #define T3126_NAME "T3126" #define TRESELECT_NAME "TRESELECT" #define TREG_NAME "TREG" #define TABORT_NAME "TABORT" /* * MAX_RR_TIMER * * Description : The constant define the number of timer * available in the timer pool. */ #define MAX_RR_TIMER 6 /* * PERIODS OF MEASUREMENT REPORTS * * Description : The constants defines the time between * measurement reports in idle or dedicated * mode as a multiple of 480 ms. */ #define PERIODS_OF_480MS_DEDICATED 1 #define PERIODS_OF_480MS_IDLE 2 /* * MEDIUM_RXLEV_THRESHOLD * * Description : The constant defines the RxLev threshold for reasonably * strong carriers */ #define MEDIUM_RXLEV_THRESHOLD 10 /* * UPPER_RXLEV_THRESHOLD * * Description : The constant defines the Upper RxLev threshold for * strong carriers */ #define UPPER_RXLEV_THRESHOLD 20 /* * MAX_LAI * * Description : The constant defines the length of the forbidden * LAI list. */ #define MAX_LAI 10 /* * MAX_RR_STORED_PRIM * * Description : The constant defines the number of primitives stored * in radio resource in parallel. */ /* * DG 1.8.2000 * #define MAX_RR_STORED_PRIM 5 * Forum G23M-0087, more than 5 prims to store */ #define MAX_RR_STORED_PRIM 10 /* * FRAME_OFFSET_ZERO * * Description : If the system ensures that the frame offset * for RR message is 24 bits, that means DL * start at offset zero, this option can be used * for an optimized access to the SDU. */ #undef FRAME_OFFSET_ZERO /* * C1 OFFSET * * Description : If no test sim card is inserted, this offset * is added to the calculated c1 value. This * ensures coverage for mobiles with a RF * at the lower border of sensitivity. */ #define C1_OFFSET 4 /* * DELAY BEFORE RESET IN CASE NO CONFIGURATION DATA AVAILABLE * * Description : At system start the software tries to read configuration * data from the flash [file system (FFS)] to allow behaviour * fitting to a customer's configuration, e.g. in terms of * HW suport (supported frequency bands, power class etc...) * If no such data can be found the system will reset after * the dalay specified below (unit is milliseconds). A customer * might use this time to download the configuration to the * flash. * Introduced with ConQuest Issue 7510, project G23M. */ #define DELAY_RESET_NO_CONFIG_DATA 30000 /* * DELAY BETWEEN NON PARALLEL SEARCH IN LIMITED SERVICE IN ALL FREQ AREA * * Description : When MS enters Limited Service in all freqqurncy are, * Non Parallel search must be used to get back to Full Service. * The following constant identifies the time gap between Non * Parallel search attempts in such a situation following TREG * timer expiry. This time gap is used to allow time for emegency * calls to the user. */ #define DELAY_NON_PAR_SEARCH_LIM_SER TWO_MIN /* * VSI_CALLER * * Description : For multithread applications the constant VSI_CALLER * must be defined to identify the calling thread of the * VSI-Interface. This must be done correponding to the * type of T_VSI_CALLER in VSI.H. The comma symbol is * neccessary because the vsi-functions are called * like this vsi_xxx (VSI_CALLER par2, par3 ...) */ #ifdef OPTION_MULTITHREAD #define VSI_CALLER rr_handle, #define VSI_CALLER_SINGLE rr_handle #else #define VSI_CALLER #define VSI_CALLER_SINGLE #endif #endif