view src/cs/layer1/cust0/l1_rf12.h @ 640:16eb1b9640dc

target gtm900 renamed to gtm900mgc2 This change reflects the fact that the build target in question supports MGC2GSMT hardware only, and will NOT work on other hw that confusing bears the same end user name of GTM900, neither the LoCosto-based GTM900-C nor the Calypso-based MG01GSMT that has a different and incompatible RFFE. If we ever get our hands on a piece of MG01GSMT hw and add support for it, that other target will be named gtm900mg01.
author Mychaela Falconia <falcon@freecalypso.org>
date Fri, 31 Jan 2020 00:46:07 +0000
parents 92dbfa906f66
children
line wrap: on
line source

/************* Revision Controle System Header *************
 *                  GSM Layer 1 software
 *
 *        Filename l1_rf12.h
 *  Copyright 2003 (C) Texas Instruments  
 * 
 ************* Revision Controle System Header *************/

#ifndef __L1_RF_H__
#define __L1_RF_H__

#include "fc-target.h"

#define RF_RITA_10 0x2030 // Check with TIDK

//#define RF_HW_BAND_EGSM
//#define RF_HW_BAND_DCS
#define RF_HW_BAND_PCS 0x4
#define RF_HW_BAND_DUAL_US  0x80
#define RF_HW_BAND_DUAL_EXT 0x20

//#define RF_HW_BAND_SUPPORT (0x0020 | RF_HW_BAND_PCS)  // radio_band_support E-GSM/DCS + PCS
// radio_band_support E-GSM/DCS + GSM850/PCS
#define RF_HW_BAND_SUPPORT (RF_HW_BAND_DUAL_EXT | RF_HW_BAND_DUAL_US)

// L1 RF SW Multiband configuration
//--------------------------

// RF_SW_MULTIBAND_SUPPORT values
#define SINGLE_BAND_900                 1
#define SINGLE_BAND_1800                2
#define SINGLE_BAND_850                 3
#define SINGLE_BAND_1900                4
#define DUAL_BAND_900_1800              5
#define DUAL_BAND_850_1900              6
#define TRI_BAND_900_1800_1900          7
#define TRI_BAND_850_1900_1800          8
#define QUAD_BAND                       9

//IMPORTANT  !: To change RF_SW_MULTIBAND_SUPPORT value, it must be synchronized with other multiband settings in the software
// To match the protocol stack settings( e.g EF_RFCAP ) in order to make sure that the value of STD sent in MPHC_INIT_L1_REQ is supported by L1
// And also match the RF HW support: RF_HW_BAND_SUPPORT
#define   RF_SW_MULTIBAND_SUPPORT   QUAD_BAND  

 // Generate band dependancy options
#define RF_SW_BAND900   ((RF_SW_MULTIBAND_SUPPORT == SINGLE_BAND_900)||(RF_SW_MULTIBAND_SUPPORT == DUAL_BAND_900_1800) \
    					||(RF_SW_MULTIBAND_SUPPORT == TRI_BAND_900_1800_1900) ||(RF_SW_MULTIBAND_SUPPORT == QUAD_BAND) )

 #define RF_SW_BAND1800  ((RF_SW_MULTIBAND_SUPPORT == SINGLE_BAND_1800) ||(RF_SW_MULTIBAND_SUPPORT == DUAL_BAND_900_1800) \
    					 ||(RF_SW_MULTIBAND_SUPPORT == TRI_BAND_900_1800_1900) ||(RF_SW_MULTIBAND_SUPPORT == TRI_BAND_850_1900_1800) \
    					 ||(RF_SW_MULTIBAND_SUPPORT == QUAD_BAND))

 #define RF_SW_BAND850    ((RF_SW_MULTIBAND_SUPPORT == SINGLE_BAND_850)||(RF_SW_MULTIBAND_SUPPORT == DUAL_BAND_850_1900) \
    					 ||(RF_SW_MULTIBAND_SUPPORT == TRI_BAND_850_1900_1800) ||(RF_SW_MULTIBAND_SUPPORT == QUAD_BAND)) 

 #define RF_SW_BAND1900  ((RF_SW_MULTIBAND_SUPPORT == SINGLE_BAND_1900)||(RF_SW_MULTIBAND_SUPPORT == DUAL_BAND_850_1900) \
 					 ||(RF_SW_MULTIBAND_SUPPORT == TRI_BAND_900_1800_1900)||(RF_SW_MULTIBAND_SUPPORT == TRI_BAND_850_1900_1800) \
 					||(RF_SW_MULTIBAND_SUPPORT == QUAD_BAND))

/************************************/
/* SYNTHESIZER setup time...        */
/************************************/
#define RX_SYNTH_SETUP_TIME (PROVISION_TIME - TRF_R1)//RX Synthesizer setup time in qbit.
#define TX_SYNTH_SETUP_TIME (- TRF_T1)               //TX Synthesizer setup time in qbit.

/************************************/
/* time for TPU scenario ending...  */
/************************************/
//
// The following values are used to take into account any TPU activity AFTER
// BDLON (or BDLENA) down (for RX) and BULON down (for TX)
// - If there are no TPU commands after BDLON (or BDLENA) down and BULON down,
//   these defines must be ZERO
// - If there IS some TPU command after BDLON (or BDLENA) and BULON down,
//   these defines must be equal to the time difference (in qbits) between 
//   the BDLON (or BDLENA) or BULON time and the last TPU command on 
//   the TPU scenario
#define RX_TPU_SCENARIO_ENDING  0   // execution time of AFTER BDLENA down
#define TX_TPU_SCENARIO_ENDING  0   // execution time of AFTER BULON down


/******************************************************/
/* TXPWR configuration...                             */
/* Fixed TXPWR value when GSM management is disabled. */
/******************************************************/

#if ((ANLG_FAM == 1) || (ANLG_FAM == 2) || (ANLG_FAM == 3))
//  #define FIXED_TXPWR       ((0xFC<<6) | AUXAPC | FALSE)  // TXPWR=10, value=252
//#define FIXED_TXPWR         ((0x65<<6) | AUXAPC | FALSE)  
  #define FIXED_TXPWR       ((0x74<<6) | AUXAPC | FALSE)  // TXPWR=15
#endif


/************************************/
/* ANALOG delay (in qbits)          */
/************************************/
#define  DL_DELAY_RF      1   // time spent in the Downlink global RF chain by the modulated signal 
#define  UL_DELAY_1RF     7   // time spent in the first  uplink RF block
#define  UL_DELAY_2RF     0   // time spent in the second uplink RF block
#if (ANLG_FAM == 1)
  #define  UL_ABB_DELAY   3   // modulator input to output delay
#endif
#if ((ANLG_FAM == 2) || (ANLG_FAM == 3))
  #define  UL_ABB_DELAY   3   // modulator input to output delay
#endif

/************************************/
/* TX Propagation delay...          */
/************************************/
 #if ((ANLG_FAM == 1) || (ANLG_FAM == 2) || (ANLG_FAM == 3))
  #define  PRG_TX       (DL_DELAY_RF + UL_DELAY_2RF + (GUARD_BITS*4) + UL_DELAY_1RF + UL_ABB_DELAY)   // = 40
#endif

/************************************/
/* Initial value for APC DELAY      */
/************************************/
#if (ANLG_FAM == 1)
//#define APCDEL_DOWN     (32 - GUARD_BITS*4)          // minimum value: 2
  #define APCDEL_DOWN      2                           // minimum value: 2
  #define APCDEL_UP       (6+5)                        // minimum value: 6
#endif

#if (ANLG_FAM == 2) || (ANLG_FAM == 3)
//#define APCDEL_DOWN     (32 - GUARD_BITS*4)          // minimum value: 2
  #define APCDEL_DOWN     (2+0)                        // minimum value: 2
  #define APCDEL_UP       (6+3+1)                      // minimum value: 6
                                                       // REMOVE // Jerome Modif for ARF7: (6+3) instead of (6+8)
#endif

#define GUARD_BITS 7

/************************************/
/* Initial value for AFC...         */
/************************************/
#define  EEPROM_AFC    ((150)*8)      // F13.3 required!!!!! (default : -952*8, initial deviation of -2400 forced)

#define  SETUP_AFC_AND_RF     6       // AFC converges in 2 frames and RF BAND GAP stable after 4 frames
                                      // Rita (RF=12) LDO wakeup requires 6 frames

/************************************/
/* Baseband registers               */
/************************************/
#if (ANLG_FAM == 1)
   // Omega registers values will be programmed at 1st DSP communication interrupt 
  #define  C_DEBUG1           0x0001                            // Enable f_tx delay of 400000 cyc DEBUG 
  #define  C_AFCCTLADD      ((0x000 << 6) | AFCCTLADD | TRUE)   // Value at reset
  #define  C_VBUCTRL        ((0x106 << 6) | VBUCTRL   | TRUE)   // Uplink gain amp 0dB, Sidetone gain to mute
  #define  C_VBDCTRL        ((0x026 << 6) | VBDCTRL   | TRUE)   // Downlink gain amp 0dB, Volume control 0 dB
  // RITA does not need an APCOFFSET because the PACTRL is internal: 
// REMOVE //#define  C_APCOFF          0x1016 | (0x3c << 6) | TRUE   // value at reset-Changed from 0x0016- CR 27.12  
  #define  C_APCOFF         ((0x040 << 6) | APCOFF    | TRUE)
  #define  C_BULIOFF        ((0x0FF << 6) | BULIOFF   | TRUE)   // value at reset
  #define  C_BULQOFF        ((0x0FF << 6) | BULQOFF   | TRUE)   // value at reset
  #define  C_DAI_ON_OFF      (0x000)                            // value at reset
  #define  C_AUXDAC         ((0x000 << 6) | AUXDAC    | TRUE)   // value at reset
  #define  C_VBCTRL         ((0x00B << 6) | VBCTRL    | TRUE)   // VULSWITCH=1, VDLAUX=1, VDLEAR=1 
  // BULRUDEL will be initialized on rach only ....
  #define  C_APCDEL1        (((APCDEL_DOWN-2) << 11)  | ((APCDEL_UP-6) << 6) | APCDEL1) 
  #define  C_BBCTRL         ((0x181 << 6) | BBCTRL    | TRUE)   // OUTLEV1=OUTLEV1=SELVMID1=SELVMID0=1 for B-sample 'modified'
#endif

#if (ANLG_FAM == 2)

  // IOTA registers values will be programmed at 1st DSP communication interrupt

  #define  C_DEBUG1          0x0001          // Enable f_tx delay of 400000 cyc DEBUG 
  #define  C_AFCCTLADD      ((0x000 << 6) | AFCCTLADD | TRUE)   // Value at reset
  #define  C_VBUCTRL        ((0x0C9 << 6) | VBUCTRL   | TRUE)   // Uplink gain amp 3 dB, Sidetone gain to -17dB
  #define  C_VBDCTRL        ((0x006 << 6) | VBDCTRL   | TRUE)   // Downlink gain amp 0dB, Volume control -12 dB
 // RITA does not need an APCOFFSET because the PACTRL is internal: 
  // REMOVE //#define  C_APCOFF          0x1016 | (0x3c << 6) | TRUE   // x2 slope 128 
#if (RF_PA == 0 || RF_PA == 3) || defined(CONFIG_TARGET_PIRELLI)
  #define  C_APCOFF         ((0x040 << 6) | APCOFF    | TRUE) // x2 slope 128
#elif defined(CONFIG_TARGET_C1XX)
  #define  C_APCOFF         ((0x060 << 6) | APCOFF    | TRUE) // x2 slope 128
#elif defined(CONFIG_TARGET_J100)
  #define  C_APCOFF         ((0x074 << 6) | APCOFF    | TRUE) // x2 slope 128
#elif (RF_PA == 1 || RF_PA == 2 || RF_PA == 4)
  #define  C_APCOFF         ((0x070 << 6) | APCOFF    | TRUE) // x2 slope 128
#endif
  #define  C_BULIOFF        ((0x0FF << 6) | BULIOFF   | TRUE)   // value at reset
  #define  C_BULQOFF        ((0x0FF << 6) | BULQOFF   | TRUE)   // value at reset
  #define  C_DAI_ON_OFF     ((0x000 << 6) | APCOFF    | TRUE)   // value at reset
  #define  C_AUXDAC         ((0x000 << 6) | AUXDAC    | TRUE)   // value at reset


// audio patch for H2-sample:
#if (RAZ_VULSWITCH_REGAUDIO == 1)
  #define  C_VBCTRL1        ((0x003 << 6) | VBCTRL1   | TRUE)   // VBDFAUXG = 1, VULSWITCH=0, VDLAUX=1, VDLEAR=1 // jkb h2sample change
#else
  #define  C_VBCTRL1        ((0x00B << 6) | VBCTRL1   | TRUE)   // VULSWITCH=1, VDLAUX=1, VDLEAR=1 
#endif


  #define  C_VBCTRL2        ((0x000 << 6) | VBCTRL2   | TRUE)   // MICBIASEL=0, VDLHSO=0, MICAUX=0
  // BULRUDEL will be initialized on rach only ....
  #define  C_APCDEL1        (((APCDEL_DOWN-2) << 11)  | ((APCDEL_UP-6) << 6) | APCDEL1)  
  #define  C_APCDEL2        ((0x000 << 6) | APCDEL2   | TRUE)                          //
  #define  C_BBCTRL         ((0x2C1 << 6) | BBCTRL    | TRUE)   // Internal autocalibration, Output common mode=1.35V
                                             // Monoslot, Vpp=8/15*Vref                                             
  #define  C_BULGCAL        ((0x000 << 6) | BULGCAL   | TRUE) // IAG=0 dB, QAG=0 dB 
#endif

#if (ANLG_FAM == 3)

  // SYREN registers values will be programmed at 1st DSP communication interrupt

  #define  C_DEBUG1          0x0001                      // Enable f_tx delay of 400000 cyc DEBUG 
  #define  C_AFCCTLADD      ((0x000 << 6) | AFCCTLADD | TRUE)   // Value at reset
  #define  C_VBUCTRL        ((0x0C9 << 6) | VBUCTRL   | TRUE)   // Uplink gain amp 3dB, Sidetone gain to -17 dB
  #define  C_VBDCTRL        ((0x006 << 6) | VBDCTRL   | TRUE)   // Downlink gain amp 0dB, Volume control -12 dB
#if (RF_PA == 0 || RF_PA == 3) 
  #define  C_APCOFF         ((0x040 << 6) | APCOFF    | TRUE)  // x2 slope 128 
#elif (RF_PA == 1 || RF_PA == 2 || RF_PA == 4) 
  #define  C_APCOFF         ((0x070 << 6) | APCOFF    | TRUE)  // x2 slope 128 
#endif
  #define  C_BULIOFF        ((0x0FF << 6) | BULIOFF   | TRUE)   // value at reset
  #define  C_BULQOFF        ((0x0FF << 6) | BULQOFF   | TRUE)   // value at reset
  #define  C_DAI_ON_OFF     ((0x000 << 6) | APCOFF    | TRUE)   // value at reset
  #define  C_AUXDAC         ((0x000 << 6) | AUXDAC    | TRUE)   // value at reset
  #define  C_VBCTRL1        ((0x108 << 6) | VBCTRL1   | TRUE)   // VULSWITCH=1 AUXI 28,2 dB  
  #define  C_VBCTRL2        ((0x001 << 6) | VBCTRL2   | TRUE)   // HSMIC on, SPKG gain @ 2,5dB 

  // BULRUDEL will be initialized on rach only ....
  #define  C_APCDEL1        (((APCDEL_DOWN-2) << 11)  | ((APCDEL_UP-6)<<6) | APCDEL1)  
  #define  C_APCDEL2        ((0x000 << 6) | APCDEL2   | TRUE)                          //
  #define  C_BBCTRL         ((0x2C1 << 6) | BBCTRL    | TRUE)   // Internal autocalibration, Output common mode=1.35V
                                                         // Monoslot, Vpp=8/15*Vref                                             
  #define  C_BULGCAL        ((0x000 << 6) | BULGCAL   | TRUE) // IAG=0 dB, QAG=0 dB 

  #define  C_VBPOP          ((0x004 << 6) | VBPOP     | TRUE)  // HSOAUTO enabled only
  #define  C_VAUDINITD       2                           // vaud_init_delay init 2 frames
  #define  C_VAUDCTRL       ((0x000 << 6) | VAUDCTRL  | TRUE)  // Init to zero
  #define  C_VAUOCTRL       ((0x155 << 6) | VAUOCTRL  | TRUE)  // Speech on all outputs
  #define  C_VAUSCTRL       ((0x000 << 6) | VAUSCTRL  | TRUE)  // Init to zero
  #define  C_VAUDPLL        ((0x000 << 6) | VAUDPLL   | TRUE)  // Init to zero

  // SYREN registers values programmed by L1 directly through SPI (ABB_on)

  #define  C_BBCFG          (0x44)                               // Syren Like BDLF Filter - DC OFFSET removal OFF

#endif


/************************************/
/* Automatic frequency compensation */
/************************************/
/********************* C_Psi_sta definition *****************************/
/* C_Psi_sta = (2*pi*Fr)        / (N * Fb)                              */
/*      (1)  = (2*pi*V*ppm*0.9) / (N*V*Fb)                              */
/*           regarding Vega V/N   = 2.4/4096                            */
/*           regarding VCO  ppm/V = 16 / 1   (average slope of the VCO) */
/*      (1)  = (2*pi*2.4*16*0.9) / (4096*1*270.83)                      */
/*           = 0.000195748                                              */
/* C_Psi_sta_inv = 1/C_Psi_sta = 5108                                   */
/************************************************************************/

#ifdef CONFIG_TARGET_PIRELLI

/* matching Pirelli's fw as read out via rftr 9 */
#define  C_Psi_sta_inv    6974L    // (1/C_Psi_sta)
#define  C_Psi_st         8L       // C_Psi_sta * 0.8 F0.16
#define  C_Psi_st_32      492713L  // F0.32
#define  C_Psi_st_inv     8717L    // (1/C_Psi_st)

#elif defined(CONFIG_TARGET_GTAMODEM) || defined(CONFIG_TARGET_FCFAM)

/*
 * We calibrate our VCXO per unit following OM's precedent,
 * thus the compiled-in AFC params don't really matter on FC/OM targets,
 * but let's put in some numbers that are representative of our VCXO,
 * as opposed to the totally wrong numbers corresponding to the
 * significantly different VCXO on the original Leonardo.
 */

#define  C_Psi_sta_inv    3462L    // (1/C_Psi_sta)
#define  C_Psi_st         15L      // C_Psi_sta * 0.8 F0.16
#define  C_Psi_st_32      992326L  // F0.32
#define  C_Psi_st_inv     4328L    // (1/C_Psi_st)

#else

/* original TCS211 values */
#define  C_Psi_sta_inv    5419L    // (1/C_Psi_sta)
#define  C_Psi_st         10L      // C_Psi_sta * 0.8 F0.16
#define  C_Psi_st_32      634112L  // F0.32
#define  C_Psi_st_inv     6773L    // (1/C_Psi_st)

#endif

#if (VCXO_ALGO == 1)
// Linearity parameters

#ifdef CONFIG_TARGET_COMPAL
  /* matching Compal's fw as read out via rftr 9 */
  #define  C_AFC_DAC_CENTER     ((1000)*8)
  #define  C_AFC_DAC_MIN        ((-500)*8)
  #define  C_AFC_DAC_MAX        ((2500)*8)
#else
  /* original TCS211 values */
  #define  C_AFC_DAC_CENTER     ((111)*8)
  #define  C_AFC_DAC_MIN        ((-1196)*8)
  #define  C_AFC_DAC_MAX        ((1419)*8)
#endif

  #define  C_AFC_SNR_THR        2560     //  1/0.4    * 2**10
#endif

typedef struct
{
  WORD16  eeprom_afc;
  UWORD32 psi_sta_inv;
  UWORD32 psi_st;
  UWORD32 psi_st_32;
  UWORD32 psi_st_inv;

  #if (VCXO_ALGO)
  // VCXO adjustment parameters
  // Parameters used when assuming linearity
  WORD16  dac_center;
  WORD16  dac_min;
  WORD16  dac_max;
    WORD16  snr_thr;
  #endif
}
T_AFC_PARAMS;

/************************************/
/* Swap IQ definitions...           */
/************************************/
/* 0=No Swap, 1=Swap RX only, 2=Swap TX only, 3=Swap RX and TX */
#if (RF_PG == R_PG_10)
    // PG 1.0 -> 1 (Swap RX only)
    // GSM 850 => TX is ALWAYS swapped compared to GSM 900
    #define  SWAP_IQ_GSM    1
    #define  SWAP_IQ_DCS    1
    #define  SWAP_IQ_PCS    1
    #define  SWAP_IQ_GSM850 3   // Swap TX compared to GSM 900
#else
    // All PG versions ABOVE 1.0 -> 0 (No Swap)
    // GSM 850 => TX is ALWAYS swapped compared to GSM 900
    #define  SWAP_IQ_GSM    0
    #define  SWAP_IQ_DCS    0
    #define  SWAP_IQ_PCS    0
    #define  SWAP_IQ_GSM850 2   // Swap TX compared to GSM 900
#endif

/************************************/
/************************************/
// typedef
/************************************/
/************************************/

/*************************************************************/
/* Define structure for apc of TX Power                 ******/
/*************************************************************/
typedef struct 
{ // pcm-file "rf/tx/level.gsm|dcs"
  UWORD16 apc;            // 0..31
  UWORD8  ramp_index;     // 0..RF_TX_RAMP_SIZE
  UWORD8  chan_cal_index; // 0..RF_TX_CHAN_CAL_TABLE_SIZE
} 
T_TX_LEVEL;

/************************************/
/* Automatic Gain Control           */
/************************************/
/* Define structure for sub-band definition of TX Power ******/ 
typedef struct 
   {
   UWORD16  upper_bound;     //highest physical arfcn of the sub-band 
   WORD16    agc_calib;      // AGC  for each TXPWR
   }T_RF_AGC_BAND;

/************************************/
/*       Ramp definitions           */
/************************************/
#if ((ANLG_FAM == 1) || (ANLG_FAM == 2) || (ANLG_FAM == 3))
  typedef struct
  {
    UWORD8  ramp_up     [16];  // Ramp-up profile
    UWORD8  ramp_down   [16];  // Ramp-down profile
  }
  T_TX_RAMP;
#endif


// RF structure definition
//========================

// Number of bands supported
#define GSM_BANDS 2

#define MULTI_BAND1     0
#define MULTI_BAND2     1
// RF table sizes
#define RF_RX_CAL_CHAN_SIZE 10       // number of AGC sub-bands
#define RF_RX_CAL_TEMP_SIZE 11       // number of temperature ranges

#define RF_TX_CHAN_CAL_TABLE_SIZE  4 // channel calibration table size 
#define RF_TX_NUM_SUB_BANDS        8 // number of sub-bands in channel calibration table
#define RF_TX_LEVELS_TABLE_SIZE   32 // level table size  
#define RF_TX_RAMP_SIZE           16 // number of ramp definitions
#define RF_TX_CAL_TEMP_SIZE        5 // number of temperature ranges

#define AGC_TABLE_SIZE            20 
#define MIN_AGC_INDEX              6

#define TEMP_TABLE_SIZE          131 // number of elements in ADC->temp conversion table


// RX parameters and tables
//-------------------------

// AGC parameters and tables
typedef struct
{
  UWORD16 low_agc_noise_thr;
  UWORD16 high_agc_sat_thr;
  UWORD16 low_agc;
  UWORD16 high_agc;
  UWORD8  il2agc_pwr[121];
  UWORD8  il2agc_max[121];
  UWORD8  il2agc_av[121];
}
T_AGC;

// Calibration parameters
typedef struct
{
  UWORD16 g_magic;
  UWORD16 lna_att;
  UWORD16 lna_switch_thr_low;
  UWORD16 lna_switch_thr_high;
}
T_RX_CAL_PARAMS;   

// RX temperature compensation
typedef struct
{
  WORD16 temperature;
  WORD16 agc_calib;
}
T_RX_TEMP_COMP;

// RF RX structure
typedef struct
{
  T_AGC              agc;
}
T_RF_RX; //common

// RF RX structure
typedef struct
{
  T_RX_CAL_PARAMS rx_cal_params;
  T_RF_AGC_BAND   agc_bands[RF_RX_CAL_CHAN_SIZE];
  T_RX_TEMP_COMP  temp[RF_RX_CAL_TEMP_SIZE];
}
T_RF_RX_BAND;


// TX parameters and tables
//-------------------------

// TX temperature compensation
typedef struct
{
  WORD16 temperature;
  #if (ORDER2_TX_TEMP_CAL==1)
  WORD16 a;
  WORD16 b;
  WORD16 c;
  #else
  WORD16 apc_calib;          
  #endif
}
T_TX_TEMP_CAL;

// Ramp up and ramp down delay
typedef struct
{
  UWORD16 up;
  UWORD16 down;
}
T_RAMP_DELAY;

typedef struct 
{
  UWORD16 arfcn_limit;
  WORD16  chan_cal;
} 
T_TX_CHAN_CAL; 

// RF TX structure
typedef struct
{
  T_RAMP_DELAY   ramp_delay;
  UWORD8         guard_bits;  // number of guard bits needed for ramp up
  UWORD8         prg_tx;
}
T_RF_TX; //common
  
// RF TX structure
typedef struct
{
  T_TX_LEVEL           levels[RF_TX_LEVELS_TABLE_SIZE];
  T_TX_CHAN_CAL        chan_cal_table[RF_TX_CHAN_CAL_TABLE_SIZE][RF_TX_NUM_SUB_BANDS];
  T_TX_RAMP            ramp_tables[RF_TX_RAMP_SIZE];
  T_TX_TEMP_CAL        temp[RF_TX_CAL_TEMP_SIZE];
}
T_RF_TX_BAND;

// band structure 
typedef struct
{
  T_RF_RX_BAND  rx;
  T_RF_TX_BAND  tx;
  UWORD8        swap_iq;
}
T_RF_BAND;  
  
// RF structure 
typedef struct
{
  // common for all bands
  UWORD16      rf_revision;
  UWORD16      radio_band_support;
  T_RF_RX      rx;
  T_RF_TX      tx;
  T_AFC_PARAMS afc;
}
T_RF;

/************************************/
/*       MADC definitions           */
/************************************/
// Omega: 5 external channels if touch screen not used, 3 otherwise
enum ADC_INDEX {
   ADC_VBAT,
   ADC_VCHARG,
   ADC_ICHARG,
   ADC_VBACKUP,
   ADC_BATTYP,
   ADC_BATTEMP,
   ADC_ADC3,     // name of this ??
   ADC_RFTEMP,
   ADC_ADC4,
   ADC_INDEX_END // ADC_INDEX_END must be the end of the enums
};

typedef struct
{
    WORD16 converted[ADC_INDEX_END];  // converted
    UWORD16 raw[ADC_INDEX_END];       // raw from ADC
}
T_ADC;

/************************************/
/*       MADC calibration           */
/************************************/
typedef struct
{
   UWORD16 a[ADC_INDEX_END];
   WORD16 b[ADC_INDEX_END];
}
T_ADCCAL;

// Conversion table: ADC value -> temperature
typedef struct 
{
    UWORD16 adc;  // ADC reading is 10 bits
    WORD16  temp; // temp is in approx. range -30..+80
}
T_TEMP;

typedef struct
{
    char *name;
    void *addr;
    int  size;
}
T_CONFIG_FILE;

typedef struct
{
  char      *name;         // name of ffs file suffix
  T_RF_BAND *addr;         // address to default flash structure
  UWORD16   max_carrier;   // max carrier 
  UWORD16   max_txpwr;     // max tx power
}
T_BAND_CONFIG;

typedef struct
{
  UWORD8  band[GSM_BANDS]; // index to band address
  UWORD8  txpwr_tp;        // tx power turning point  
  UWORD16 first_arfcn;     // first index
}
T_STD_CONFIG;
enum GSMBAND_DEF 
{
  BAND_NONE,
  BAND_EGSM900,
  BAND_DCS1800,
  BAND_PCS1900,
  BAND_GSM850,
  // put new bands here
  BAND_GSM900  //last entry
};

/************************************/
/* ABB (Omega) Initialization       */
/************************************/

#if ((ANLG_FAM == 1) || (ANLG_FAM == 2))
#define ABB_TABLE_SIZE 16
#elif (ANLG_FAM == 3)
  #define ABB_TABLE_SIZE 22
#endif

// Note that this translation is probably not needed at all. But until L1 is
// (maybe) changed to simply initialize the ABB from a table of words, we
// use this to make things more easy-readable.

#if (ANLG_FAM == 1)
  enum ABB_REGISTERS {
    ABB_AFCCTLADD = 0,
    ABB_VBUCTRL,
    ABB_VBDCTRL,
    ABB_BBCTRL,
    ABB_APCOFF,
    ABB_BULIOFF,
    ABB_BULQOFF,
    ABB_DAI_ON_OFF,
    ABB_AUXDAC,
    ABB_VBCTRL,
    ABB_APCDEL1
  };
#elif (ANLG_FAM == 2)
  enum ABB_REGISTERS {
    ABB_AFCCTLADD = 0,
    ABB_VBUCTRL,
    ABB_VBDCTRL,
    ABB_BBCTRL,
    ABB_BULGCAL,
    ABB_APCOFF,
    ABB_BULIOFF,
    ABB_BULQOFF,
    ABB_DAI_ON_OFF,
    ABB_AUXDAC,
    ABB_VBCTRL1,
    ABB_VBCTRL2,
    ABB_APCDEL1,
    ABB_APCDEL2
  };
#elif (ANLG_FAM == 3)
  enum ABB_REGISTERS {
    ABB_AFCCTLADD = 0,
    ABB_VBUCTRL,
    ABB_VBDCTRL,
    ABB_BBCTRL,
    ABB_BULGCAL,
    ABB_APCOFF,
    ABB_BULIOFF,
    ABB_BULQOFF,
    ABB_DAI_ON_OFF,
    ABB_AUXDAC,
    ABB_VBCTRL1,
    ABB_VBCTRL2,
    ABB_APCDEL1,
    ABB_APCDEL2,
    ABB_VBPOP,
    ABB_VAUDINITD,
    ABB_VAUDCTRL,
    ABB_VAUOCTRL,
    ABB_VAUSCTRL,
    ABB_VAUDPLL
  };
#endif
#endif