FreeCalypso > hg > fc-magnetite
view cdg211/cdginc/m_grlc.val @ 629:3231dd9b38c1
armio.c: make GPIOs 8 & 13 outputs driving 1 on all "classic" targets
Calypso GPIOs 8 & 13 are pinmuxed with MCUEN1 & MCUEN2, respectively,
and on powerup these pins are MCUEN, i.e., outputs driving 1. TI's code
for C-Sample and earlier turns them into GPIOs configured as outputs also
driving 1 - so far, so good - but TI's code for BOARD 41 (which covers
D-Sample, Leonardo and all real world Calypso devices derived from the
latter) switches them from MCUEN to GPIOs, but then leaves them as inputs.
Given that the hardware powerup state of these two pins is outputs driving 1,
every Calypso board design MUST be compatible with such driving; typically
these GPIO signals will be either unused and unconnected or connected as
outputs driving some peripheral. Turning these pins into GPIO inputs will
result in floating inputs on every reasonably-wired board, thus I am
convinced that this configuration is nothing but a bug on the part of
whoever wrote this code at TI.
This floating input bug had already been fixed earlier for GTA modem and
FCDEV3B targets; the present change makes the fix unconditional for all
"classic" targets. The newly affected targets are D-Sample, Leonardo,
Tango and GTM900.
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Thu, 02 Jan 2020 05:38:26 +0000 |
parents | 56abf6cf8a0b |
children |
line wrap: on
line source
/* +--------------------------------------------------------------------------+ | PROJECT : PROTOCOL STACK | | FILE : m_grlc.val | | SOURCE : "__out__\g23m_dfile\msg\grlc.mdf" | | LastModified : "2003-03-26" | | IdAndVersion : "8441.601.99.001" | | SrcFileTime : "Thu Feb 17 14:27:10 2005" | | Generated by CCDGEN_2.5.5 on Fri Jun 08 13:59:14 2007 | | !!DO NOT MODIFY!!DO NOT MODIFY!!DO NOT MODIFY!! | +--------------------------------------------------------------------------+ */ /* PRAGMAS * PREFIX : NONE * COMPATIBILITY_DEFINES : NO (require PREFIX) * ALWAYS_ENUM_IN_VAL_FILE: NO * ENABLE_GROUP: NO * CAPITALIZE_TYPENAME: NO */ #ifndef M_GRLC_VAL #define M_GRLC_VAL #define CDG_ENTER__M_GRLC_VAL #define CDG_ENTER__FILENAME _M_GRLC_VAL #define CDG_ENTER__M_GRLC_VAL__FILE_TYPE CDGINC #define CDG_ENTER__M_GRLC_VAL__LAST_MODIFIED _2003_03_26 #define CDG_ENTER__M_GRLC_VAL__ID_AND_VERSION _8441_601_99_001 #define CDG_ENTER__M_GRLC_VAL__SRC_FILE_TIME _Thu_Feb_17_14_27_10_2005 #include "CDG_ENTER.h" #undef CDG_ENTER__M_GRLC_VAL #undef CDG_ENTER__FILENAME #include "m_rr_com.val" /* Access values independent from the corresponding h-file. */ /* * Value constants for VAL_final_alloc */ #define NO (0x0) /* not present */ #define YES (0x1) /* present */ /* * Value constants for VAL_msg_type */ #define U_GRLC_RESOURCE_REQ_c (0x5) /* Packet Resource Request */ #define U_GRLC_DL_ACK_c (0x2) /* Packet Downlink Ack/Nack */ #define D_GRLC_UL_ACK_c (0x9) /* Packet Uplink Ack/Nack */ #define U_GRLC_CTRL_ACK_c (0x1) /* Packet Control Acknowledgement */ #define U_GRLC_UL_DUMMY_c (0x3) /* Packet Uplink Dummy Control Block */ /* * Value constants for VAL_page_mode */ #define NORMAL_PAGING (0x0) /* Normal Paging */ #define EXT_PAGING (0x1) /* Extended Paging */ #define REORG_PAGING (0x2) /* Paging Reorganisation */ #define SAME_PAGING (0x3) /* Same as before */ /* * Value constants for VAL_access_type */ #define TWO_PHASE (0x0) /* Two Phase Access Request */ #define PAGE (0x1) /* Page Response */ #define CELL_UPDATE (0x2) /* Cell Update */ #define MM_PROC (0x3) /* Mobility Management procedure */ /* * Value constants for VAL_chan_coding_cmd */ #define VAL_CHAN_CODING_CMD___0 (0x0) /* CS-1 */ #define VAL_CHAN_CODING_CMD___1 (0x1) /* CS-2 */ #define VAL_CHAN_CODING_CMD___2 (0x2) /* CS-3 */ #define VAL_CHAN_CODING_CMD___3 (0x3) /* CS-4 */ /* * Value constants for VAL_rlc_mode */ #define VAL_RLC_MODE___0 (0x0) /* RLC acknowledged mode */ #define VAL_RLC_MODE___1 (0x1) /* RLC unacknowledged mode */ /* * Value constants for VAL_pctrl_ack */ #define VAL_PCTRL_ACK___0 (0x0) /* reserved - this value shall not be sent. If received it shall be interpreted as bit value '1'. */ #define VAL_PCTRL_ACK___1 (0x1) /* the MS received an RLC/MAC control block addressed to itself and with RBSN = 1, and did not receive an RLC/MAC control block with the same RTI value and RBSN = 0. */ #define VAL_PCTRL_ACK___2 (0x2) /* the MS received an RLC/MAC control block addressed to itself and with RBSN = 0, and did not receive an RLC/MAC control block with the same RTI value and RBSN = 1. This value is sent irrespective of the value of the FS bit. */ #define VAL_PCTRL_ACK___3 (0x3) /* the MS received two RLC/MAC blocks with the same RTI value, one with RBSN = 0 and the other with RBSN = 1. */ /* * Value constants for VAL_alpha */ #define VAL_ALPHA___0 (0x0) /* Alpha = 0.0 */ #define VAL_ALPHA___1 (0x1) /* Alpha = 0.1 */ #define VAL_ALPHA___2 (0x2) /* Alpha = 0.2 */ #define VAL_ALPHA___3 (0x3) /* Alpha = 0.3 */ #define VAL_ALPHA___4 (0x4) /* Alpha = 0.4 */ #define VAL_ALPHA___5 (0x5) /* Alpha = 0.5 */ #define VAL_ALPHA___6 (0x6) /* Alpha = 0.6 */ #define VAL_ALPHA___7 (0x7) /* Alpha = 0.7 */ #define VAL_ALPHA___8 (0x8) /* Alpha = 0.8 */ #define VAL_ALPHA___9 (0x9) /* Alpha = 0.9 */ #define VAL_ALPHA___A (0xa) /* Alpha = 1.0 */ /* * Value constants for VAL_radio_prio */ #define VAL_RADIO_PRIO___0 (0x0) /* Radio Priority 1 (Highest priority) */ #define VAL_RADIO_PRIO___1 (0x1) /* Radio Priority 2 */ #define VAL_RADIO_PRIO___2 (0x2) /* Radio Priority 3 */ #define VAL_RADIO_PRIO___3 (0x3) /* Radio Priority 4 (Lower priority) */ /* * Value constants for VAL_llc_pdu_type */ #define VAL_LLC_PDU_TYPE___0 (0x0) /* LLC PDU is SACK or ACK */ #define VAL_LLC_PDU_TYPE___1 (0x1) /* LLC PDU is not SACK or ACK */ /* * Value constants for VAL_bl_o_bl_per */ #define BLOCKS (0x0) /* ALLOCATION_BITMAP is to be interpreted as blocks */ #define BLOCK_PERIODS (0x1) /* ALLOCATION_BITMAP is to be interpreted as block periods */ /* * Value constants for VAL_rbb */ #define INVALID (0x0) /* Negative Ack of the RLC data block with BSN=(SSN-bit_nr)mod128 */ #define RECEIVED (0x1) /* Positive Ack of the RLC data block with BSN=(SSN-bit_nr)mod128 */ /* * Value constants for VAL_f_ack_ind */ #define VAL_F_ACK_IND___0 (0x0) /* retransmission are requested and the TBF is incomplete */ #define VAL_F_ACK_IND___1 (0x1) /* no retransmissions are requested and this message indicates acknowledgement of all RLC data in the TBF */ #include "CDG_LEAVE.h" #endif