FreeCalypso > hg > fc-magnetite
view cdg3/cdginc-locosto/p_rrlp.val @ 629:3231dd9b38c1
armio.c: make GPIOs 8 & 13 outputs driving 1 on all "classic" targets
Calypso GPIOs 8 & 13 are pinmuxed with MCUEN1 & MCUEN2, respectively,
and on powerup these pins are MCUEN, i.e., outputs driving 1. TI's code
for C-Sample and earlier turns them into GPIOs configured as outputs also
driving 1 - so far, so good - but TI's code for BOARD 41 (which covers
D-Sample, Leonardo and all real world Calypso devices derived from the
latter) switches them from MCUEN to GPIOs, but then leaves them as inputs.
Given that the hardware powerup state of these two pins is outputs driving 1,
every Calypso board design MUST be compatible with such driving; typically
these GPIO signals will be either unused and unconnected or connected as
outputs driving some peripheral. Turning these pins into GPIO inputs will
result in floating inputs on every reasonably-wired board, thus I am
convinced that this configuration is nothing but a bug on the part of
whoever wrote this code at TI.
This floating input bug had already been fixed earlier for GTA modem and
FCDEV3B targets; the present change makes the fix unconditional for all
"classic" targets. The newly affected targets are D-Sample, Leonardo,
Tango and GTM900.
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Thu, 02 Jan 2020 05:38:26 +0000 |
parents | c15047b3d00d |
children |
line wrap: on
line source
/* +--------------------------------------------------------------------------+ | PROJECT : PROTOCOL STACK | | FILE : p_rrlp.val | | SOURCE : "sap\rrlp.pdf" | | LastModified : "2002-11-13" | | IdAndVersion : "8443.102.02.100" | | SrcFileTime : "Thu Nov 29 09:53:06 2007" | | Generated by CCDGEN_2.5.5A on Thu Sep 25 09:18:53 2014 | | !!DO NOT MODIFY!!DO NOT MODIFY!!DO NOT MODIFY!! | +--------------------------------------------------------------------------+ */ /* PRAGMAS * PREFIX : NONE * COMPATIBILITY_DEFINES : NO (require PREFIX) * ALWAYS_ENUM_IN_VAL_FILE: NO * ENABLE_GROUP: NO * CAPITALIZE_TYPENAME: NO */ #ifndef P_RRLP_VAL #define P_RRLP_VAL #define CDG_ENTER__P_RRLP_VAL #define CDG_ENTER__FILENAME _P_RRLP_VAL #define CDG_ENTER__P_RRLP_VAL__FILE_TYPE CDGINC #define CDG_ENTER__P_RRLP_VAL__LAST_MODIFIED _2002_11_13 #define CDG_ENTER__P_RRLP_VAL__ID_AND_VERSION _8443_102_02_100 #define CDG_ENTER__P_RRLP_VAL__SRC_FILE_TIME _Thu_Nov_29_09_53_06_2007 #include "CDG_ENTER.h" #undef CDG_ENTER__P_RRLP_VAL #undef CDG_ENTER__FILENAME /* * Value constants for VAL_cause */ #define RRLP_METHOD_INVALID (0x7) /* Position method is not supported */ #define RRLP_REF_BTS_INVALID (0xa) /* The ref. BTS for E-OTD is not the serving BTS */ #define RRLP_HANDOVER (0x14) /* The measurement procedure was interrupted by a handover. No RRLP specific error message is created. */ /* * Value constants for VAL_exp_otd */ /* * Value constants for VAL_loc_method */ #define EOTD_METHOD (0x0) #define GPS_METOD (0x1) #define GPS_OR_EOTD_METOD (0x2) /* * Value constants for VAL_mfrm_offset */ /* * Value constants for VAL_otd_type */ #define ROUGH_RTD (0x0) /* only rough RTD has been provided by the NW */ #define EXPECTED_OTD (0x1) /* only expectedOTD has been provided by the NW */ #define BOTH_OTD (0x2) /* Both OTD / RTD types have been provided by the NW */ /* * Value constants for VAL_pos_method */ #define MS_ASSISTED (0x0) #define MS_BASED (0x1) #define MS_BASED_PREF (0x2) #define MS_ASSISTED_PREF (0x3) /* * Value constants for VAL_rough_rtd */ /* * Value constants for VAL_ta_correction_present */ #define TA_PRESENT (0x1) /* TA present */ #define TA_NOT_PRESENT (0x0) /* TA NOT present */ /* * Value constants for VAL_uncertainty */ #define UNC_MAX_2BIT (0x0) /* uncertainty in bits. 0 - 2 bits */ #define UNC_MAX_4BIT (0x1) /* uncertainty in bits. 3 - 4 bits */ #define UNC_MAX_8BIT (0x2) /* uncertainty in bits. 5 - 8 bits */ #define UNC_MAX_12BIT (0x3) /* uncertainty in bits. 9 - 12 bits */ #define UNC_MAX_16BIT (0x4) /* uncertainty in bits. 13 - 16 bits */ #define UNC_MAX_22BIT (0x5) /* uncertainty in bits. 17 - 22 bits */ #define UNC_MAX_30BIT (0x6) /* uncertainty in bits. 23 - 30 bits */ #define UNC_GT_30BIT (0x7) /* uncertainty in bits. > 30 bits */ /* * user defined constants */ #define R_NUM_MEAS_SETS (0x3) #define R_MAX_REF_NEIGH_BTS (0xf) #define MAX_NCELL_EOTD (0xf) #include "CDG_LEAVE.h" #endif