FreeCalypso > hg > fc-magnetite
view cdg3/sap/ipa.pdf @ 629:3231dd9b38c1
armio.c: make GPIOs 8 & 13 outputs driving 1 on all "classic" targets
Calypso GPIOs 8 & 13 are pinmuxed with MCUEN1 & MCUEN2, respectively,
and on powerup these pins are MCUEN, i.e., outputs driving 1. TI's code
for C-Sample and earlier turns them into GPIOs configured as outputs also
driving 1 - so far, so good - but TI's code for BOARD 41 (which covers
D-Sample, Leonardo and all real world Calypso devices derived from the
latter) switches them from MCUEN to GPIOs, but then leaves them as inputs.
Given that the hardware powerup state of these two pins is outputs driving 1,
every Calypso board design MUST be compatible with such driving; typically
these GPIO signals will be either unused and unconnected or connected as
outputs driving some peripheral. Turning these pins into GPIO inputs will
result in floating inputs on every reasonably-wired board, thus I am
convinced that this configuration is nothing but a bug on the part of
whoever wrote this code at TI.
This floating input bug had already been fixed earlier for GTA modem and
FCDEV3B targets; the present change makes the fix unconditional for all
"classic" targets. The newly affected targets are D-Sample, Leonardo,
Tango and GTM900.
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Thu, 02 Jan 2020 05:38:26 +0000 |
parents | c15047b3d00d |
children |
line wrap: on
line source
;******************************************************************************** ;*** File : ipa.pdf ;*** Creation : Wed Mar 11 09:58:13 CST 2009 ;*** XSLT Processor : Apache Software Foundation / http://xml.apache.org/xalan-j / supports XSLT-Ver: 1 ;*** Copyright : (c) Texas Instruments AG, Berlin Germany 2002 ;******************************************************************************** ;*** Document Type : Service Access Point Specification ;*** Document Name : ipa ;*** Document No. : 8444.104.02.007 ;*** Document Date : 2003-08-30 ;*** Document Status: BEING_PROCESSED ;*** Document Author: Jacek ;******************************************************************************** PRAGMA SRC_FILE_TIME "Thu Nov 29 09:43:54 2007" PRAGMA LAST_MODIFIED "2003-08-30" PRAGMA ID_AND_VERSION "8444.104.02.007" CONST IPA_ENTITY_NAME_LEN 6 ; maximum length of entity name including NULL VALTAB VAL_dti_conn VAL 0 IPA_CONNECT_DTI "Connect DTI2 to IP" VAL 1 IPA_DISCONNECT_DTI "Disconnect DTI2 from IP" VALTAB VAL_link_id VAL 0 IPA_LINK_ID_DEFAULT "Default link id" VALTAB VAL_dti_direction VAL 0 IPA_DTI_TO_HIGHER_LAYER "DTI2 used normally" VAL 1 IPA_DTI_TO_LOWER_LAYER "DTI2 is inverted" VALTAB VAL_cmd VAL 0 IPA_CONFIG_UP "enable the interface" VAL 1 IPA_CONFIG_DOWN "disable the interface" VALTAB VAL_ack_flag VAL 0 IPA_CONFIG_ACK "Acknowledged" VAL 1 IPA_CONFIG_NAK "not acknowledged" VALTAB VAL_all_down VAL 0 IPA_ALLDOWN_FALSE ">= 1 Interface still up" VAL 1 IPA_ALLDOWN_TRUE "all interfaces down" VAR dti_conn "DTI2 connect" B VAL @p_ipa - VAL_dti_conn@ VAR link_id "Link identifier" L VAL @p_ipa - VAL_link_id@ VAR dti_direction "DTI2 direction" B VAL @p_ipa - VAL_dti_direction@ VAR ip "IP address" L VAR peer_ip "peer IP address" L VAR mtu "maximum transfer unit" S VAR cmd "Command" B VAL @p_ipa - VAL_cmd@ VAR ack_flag "acknowledge flag" B VAL @p_ipa - VAL_ack_flag@ VAR all_down "all interfaces down flag" B VAL @p_ipa - VAL_all_down@ VAR entity_name "name of an neighbour entity" B ; IPA_DTI_REQ 0x8000003C ; IPA_DTI_CNF 0x8000403C ; IPA_DTI_IND 0x8001403C ; IPA_CONFIG_REQ 0x8001003C ; IPA_CONFIG_CNF 0x8002403C PRIM IPA_DTI_REQ 0x8000003C { dti_conn ; DTI connect entity_name [IPA_ENTITY_NAME_LEN] ; entity name link_id ; link identifier dti_direction ; DTI direction } PRIM IPA_DTI_CNF 0x8000403C { dti_conn ; DTI connect link_id ; link identifier } PRIM IPA_DTI_IND 0x8001403C { link_id ; link identifier } PRIM IPA_CONFIG_REQ 0x8001003C { ip ; IP address peer_ip ; peer IP address mtu ; Maximum transfer unit cmd ; Command } PRIM IPA_CONFIG_CNF 0x8002403C { ack_flag ; Acknowledge flag all_down ; all interfaces down flag }