FreeCalypso > hg > fc-magnetite
view src/cs/drivers/drv_app/uart/uartfax.h @ 581:a0a45c5eb3ef
gsmcomp.c: bumping trace partition size to 220 like in gprscomp.c
This change is safe in terms of RAM usage because all of these partition
pools have already been moved from XRAM to IRAM earlier, and our IRAM
usage in VO configs is currently quite low - the one near the limit
is XRAM on C11x.
| author | Mychaela Falconia <falcon@freecalypso.org> |
|---|---|
| date | Tue, 29 Jan 2019 03:52:49 +0000 |
| parents | 945cf7f506b2 |
| children |
line wrap: on
line source
/******************************************************************************* * * UARTFAX.H * * This driver allows to control the UARTs of chipset 1.5 for fax and data * It performs flow control: RTS/CTS, XON/XOFF. * * (C) Texas Instruments 1999 - 2003 * ******************************************************************************/ #ifndef __UARTFAX_H__ #define __UARTFAX_H__ #ifndef _WINDOWS #include "l1sw.cfg" #include "chipset.cfg" #endif #ifndef C_EXTERN #if (OP_L1_STANDALONE == 1) #define C_EXTERN extern #else #define C_EXTERN #endif #endif #include "faxdata.h" /* * In UAF_Init, a constant is used to identify the UART. */ typedef enum { UAF_UART_0, /* IrDA */ UAF_UART_1 /* Modem */ #if (CHIPSET == 12) , UAF_UART_2 /* Modem 2 */ #endif } T_fd_UartId; #if (CHIPSET == 12) #define NUMBER_OF_FD_UART (3) #else #define NUMBER_OF_FD_UART (2) #endif /******************************************************************************* * * UAF_Init * * Purpose : Initializes the UART hardware and installs interrupt handlers. * The parameters are set to the default values: * - 19200 baud, * - 8 bits / character, * - no parity, * - 1 stop bit, * - no flow control. * All functionalities of the UART driver are disabled. * * Arguments: In : uartNo: Used UART. * Out: none * * Returns : FD_OK : Successful operation. * FD_NOT_SUPPORTED: Wrong UART number. * FD_INTERNAL_ERR : Internal problem. * ******************************************************************************/ C_EXTERN T_FDRET UAF_Init (T_fd_UartId uartNo); /******************************************************************************* * * UAF_Enable * * Purpose : The functionalities of the UART driver are disabled or enabled. * In the deactivated state, all information about the communication * parameters should be stored and recalled if the driver is again * enabled. When the driver is enabled the RX and TX buffers are * cleared. * * Arguments: In : uartNo: Used UART. * : enable: 1: enable the driver * 0: disable the driver * Out: none * * Returns : FD_OK : Successful operation. * FD_NOT_SUPPORTED: Wrong UART number. * FD_INTERNAL_ERR : Internal problem with the hardware. * ******************************************************************************/ C_EXTERN T_FDRET UAF_Enable (T_fd_UartId uartNo, SYS_BOOL enable); /******************************************************************************* * * UAF_SetComPar * * Purpose : Sets up the communication parameters: baud rate, bits per * character, number of stop bits, parity. * * Arguments: In : uartNo : Used UART. * baudrate: Used baud rate. * bpc : Used bits per character. * sb : Used stop bits. * parity : Used parity. * Out: none * * Returns : FD_OK : Successful operation. * FD_NOT_SUPPORTED: The specified parameters don't fit to the * capabilities of the UART or wrong UART number. * FD_INTERNAL_ERR : Internal problem with the hardware. * ******************************************************************************/ C_EXTERN T_FDRET UAF_SetComPar (T_fd_UartId uartNo, T_baudrate baudrate, T_bitsPerCharacter bpc, T_stopBits sb, T_parity parity); /******************************************************************************* * * UAF_SetBuffer * * Purpose : Sets up the size of the circular buffers to be used in the UART * driver. This function may be called only if the UART is disabled * with UAF_Enable. * * Arguments: In : uartNo : Used UART. * bufSize : Specifies the size of the circular buffer. * rxThreshold: Amount of received bytes that leads to a call * to suspended read-out function which is passed * to the function UAF_ReadData. * txThreshold: Amount of bytes in the TX buffer to call the * suspended write-in function which is passed to * the function UAF_WriteData * Out: none * * Returns : FD_OK : Successful operation. * FD_NOT_SUPPORTED: bufSize exceeds the maximal possible * capabilities of the driver or the threshold * values don't correspond to the bufSize or * wrong UART number. * FD_INTERNAL_ERR : Internal problem with the hardware or the * function has been called while the UART is * enabled. * ******************************************************************************/ C_EXTERN T_FDRET UAF_SetBuffer (T_fd_UartId uartNo, SYS_UWORD16 bufSize, SYS_UWORD16 rxThreshold, SYS_UWORD16 txThreshold); /******************************************************************************* * * UAF_SetFlowCtrl * * Purpose : Changes the flow control mode of the UART driver. * If a flow control is activated, DTR is activated or XOFF is sent * if the RX buffer is not able to store the received characters else * DTR is deactivated or XON is sent. * * Arguments: In : uartNo: Used UART. * fcMode: flow control mode (none, DTR/DSR, RTS/CTS, XON/XOFF). * XON : ASCII code of the XON character. * XOFF : ASCII code of the XOFF character. * Out: none * * Returns : FD_OK : Successful operation. * FD_NOT_SUPPORTED: The flow control mode is not supported or wrong * UART number. * FD_INTERNAL_ERR : Internal problem with the hardware. * ******************************************************************************/ C_EXTERN T_FDRET UAF_SetFlowCtrl (T_fd_UartId uartNo, T_flowCtrlMode fcMode, SYS_UWORD8 XON, SYS_UWORD8 XOFF); /******************************************************************************* * * UAF_SetEscape * * Purpose : To return to the command mode at the ACI while a data connection * is established, an escape sequence has to be detected. * To distinguish between user data and the escape sequence a * defined guard period is necessary before and after this sequence. * * Arguments: In: uartNo : Used UART. * escChar : ASCII character which could appear three times * as an escape sequence. * guardPeriod: Denotes the minimal duration of the rest before * the first and after the last character of the * escape sequence, and the maximal receiving * duration of the whole escape string. This value * is expressed in ms. * Out: none * * Returns : FD_OK : Successful operation. * FD_NOT_SUPPORTED: Wrong UART number. * FD_INTERNAL_ERR : Internal problem with the hardware. * ******************************************************************************/ C_EXTERN T_FDRET UAF_SetEscape (T_fd_UartId uartNo, SYS_UWORD8 escChar, SYS_UWORD16 guardPeriod); /******************************************************************************* * * UAF_InpAvail * * Purpose : Returns the number of characters available in the RX buffer of the * driver. If the driver is disabled the function returns 0. * * Arguments: In : uartNo: Used UART. * Out: none * * Returns : >= 0 : The returned value is the amount of data in the * RX buffer. * FD_NOT_SUPPORTED: Wrong UART number. * FD_NOT_READY : The function is called while the callback of the * readOutFunc function is activated and still not * terminated. * FD_INTERNAL_ERR : Internal problem with the hardware. * ******************************************************************************/ C_EXTERN T_FDRET UAF_InpAvail (T_fd_UartId uartNo); /******************************************************************************* * * UAF_OutpAvail * * Purpose : Returns the number of free characters in TX buffer of the driver. * If the driver is disabled the function returns 0. * * Arguments: In : uartNo: Used UART. * Out: none * * Returns : >= 0 : The returned value is the amount of data in the * TX buffer. * FD_NOT_SUPPORTED: Wrong UART number. * FD_NOT_READY : The function is called while the callback of the * writeInFunc function is activated and still not * terminated. * FD_INTERNAL_ERR : Internal problem with the hardware. * ******************************************************************************/ C_EXTERN T_FDRET UAF_OutpAvail (T_fd_UartId uartNo); /******************************************************************************* * * UAF_EnterSleep * * Purpose : Checks if UART is ready to enter Deep Sleep. If ready, enables * wake-up interrupt. * * Arguments: In : uartNo: Used UART. * Out: none * * Returns : 0 : Deep Sleep is not possible. * >= 1 : Deep Sleep is possible. * FD_NOT_SUPPORTED: Wrong UART number. * * Warning: Parameters are not verified. * ******************************************************************************/ C_EXTERN T_FDRET UAF_EnterSleep (T_fd_UartId uartNo); /******************************************************************************* * * UAF_WakeUp * * Purpose : Wakes up UART after Deep Sleep. * * Arguments: In : uartNo: Used UART. * Out: none * * Returns : FD_OK : Successful operation. * FD_NOT_SUPPORTED: Wrong UART number. * * Warning: Parameters are not verified. * ******************************************************************************/ C_EXTERN T_FDRET UAF_WakeUp (T_fd_UartId uartNo); /******************************************************************************* * * UAF_ReadData * * Purpose : To read the received characters out of the RX buffer the address * of a function is passed. If characters are available, the driver * calls this function and pass the address and the amount of * readable characters. Because the RX buffer is circular, the * callback function may be called with more than one address of * buffer fragment. * The readOutFunc function modifies the contents of the size array * to return the driver the number of processed characters. Each * array entry is decremented by the number of bytes read in the * fragment. * If the UAF_ReadData is called while the RX buffer is empty, it * depends on the suspend parameter to suspend the call-back or to * leave without any operation. In the case of suspension, the * return value of UAF_ReadData is UAF_SUSPENDED. A delayed call-back * will be performed if: * - the RX buffer reachs the adjusted threshold (rxThreshold of * UAF_SetBuffer), * - the state of a V.24 input line has changed, * - a break is detected, * - an escape sequence is detected. * If no suspension is necessary the function returns the number of * processed bytes. * * Arguments: In : uartNo : Used UART. * suspend : mode of suspension in case of RX buffer empty. * readOutFunc: Callback function. * cldFromIrq: The driver sets this parameter to 1 * if the callback function is called * from an interrupt service routine. * reInstall : The call-back function sets this * parameter to rm_reInstall if the * driver must call again the callback * function when the RX threshold level * is reached. Else it will be set to * rm_noInstall. Before to call the * readOutFunc function this parameter * is set to rm_notDefined. * nsource : Informed the callback function about * the number of fragments which are * ready to copy from the circular RX * buffer. * source : Array which contains the addresses * of the fragments. * size : Array which contains the sizes of * each fragments. * state : The state parameter is the status * of the V.24 lines and the break / * escape detection. The state * parameter is described in the * specification of UAF_GetLineState. * Out: none * * Returns : >= 0 : Succesful operation. Amount of processed bytes. * FD_NOT_SUPPORTED: Wrong UART number. * FD_SUSPENDED : The callback is suspended until the buffer or * state condition changed. * FD_NOT_READY : The function is called while the callback is * activated and still not terminated. * FD_INTERNAL_ERR : Internal problems with the hardware. * ******************************************************************************/ C_EXTERN T_FDRET UAF_ReadData (T_fd_UartId uartNo, T_suspendMode suspend, void (readOutFunc (SYS_BOOL cldFromIrq, T_reInstMode *reInstall, SYS_UWORD8 nsource, SYS_UWORD8 *source[], SYS_UWORD16 size[], SYS_UWORD32 state))); /******************************************************************************* * * UAF_WriteData * * Purpose : To write characters into the TX buffer the address of a function * is passed. If free space is available in the buffer, the driver * calls this function and passes the destination address and the * amount of space. Because the TX buffer is circular, the callback * function may be called with more than one address of buffer * fragment. * The writeInFunc function modifies the contents of the size array * to return the driver the number of processed bytes. Each array * entry is decremented by the number of bytes written in this * fragment. * If the UAF_WriteData function is called while the TX buffer is * full, it depends on the suspend parameter to suspend the * call-back or to leave this function without any operation. In the * case of suspension the returned value of the UAF_WriteData is * UAF_SUSPENDED. A delayed call-back will be performed if the TX * buffer reaches the adjusted threshold (txThreshold of * UAF_SetBuffer). If no suspension is necessary the function returns * the number of processed bytes. * * Arguments: In : uartNo : Used UART. * suspend : mode of suspension in case of TX buffer empty. * writeInFunc: Callback function. * cldFromIrq: The driver sets this parameter to 1 * if the call-back function is called * from an interrupt service routine. * reInstall : The callback function sets this * parameter to rm_reInstall if the * driver must call again the callback * function when the TX threshold level * is reached. Else it will be set to * rm_noInstall. Before to call the * writeInFunc function this parameter * is set to rm_notDefined. * ndest : Informed the callback function about * the number of fragments which are * available in the TX buffer. * dest : Array which contains the addresses * of the fragments. * size : Array which contains the sizes of * each fragments. * Out: none * * Returns : >= 0 : Succesful operation. Amount of processed bytes. * FD_NOT_SUPPORTED: Wrong UART number. * FD_SUSPENDED : The callback is suspended until the buffer * condition changed. * FD_NOT_READY : The function is called while the callback is * activated and still not terminated. * FD_INTERNAL_ERR : Internal problems with the hardware. * ******************************************************************************/ C_EXTERN T_FDRET UAF_WriteData (T_fd_UartId uartNo, T_suspendMode suspend, void (writeInFunc (SYS_BOOL cldFromIrq, T_reInstMode *reInstall, SYS_UWORD8 ndest, SYS_UWORD8 *dest[], SYS_UWORD16 size[]))); /******************************************************************************* * * UAF_StopRec * * Purpose : If a flow control mode is set, this function tells the terminal * equipment that no more data can be received. * XON/XOFF: XOFF is sent. * DTR/DSR : DTR is desactivated. * RTS/CTS : RTS is deactivated. * * Arguments: In : uartNo: Used UART. * Out: none * * Returns : FD_OK : Successful operation. * FD_NOT_SUPPORTED: Wrong UART number. * FD_INTERNAL_ERR : Internal problem with the hardware. * ******************************************************************************/ C_EXTERN T_FDRET UAF_StopRec (T_fd_UartId uartNo); /******************************************************************************* * * UAF_StartRec * * Purpose : If a flow control mode is set, this function tells the terminal * equipment that the receiver is again able to receive more data. * If the buffer has already reached the high water mark the driver * sends the signal only if the buffer drains to a low water mark. * XON/XOFF: XON is sent. * DTR/DSR : DTR is activated. * RTS/CTS : RTS is activated. * * Arguments: In : uartNo: Used UART. * Out: none * * Returns : FD_OK : Successful operation. * FD_NOT_SUPPORTED: Wrong UART number. * FD_INTERNAL_ERR : Internal problem with the hardware. * ******************************************************************************/ C_EXTERN T_FDRET UAF_StartRec (T_fd_UartId uartNo); /******************************************************************************* * * UAF_GetLineState * * Purpose : Returns the state of the V.24 lines, the flow control state and * the result of the break/escape detection process as a bit field. * * Arguments: In : uartNo: Used UART. * Out: state : State of the V.24 lines, the flow control state and * the result of the break/escape sequence detection * process as a bit field. * * Returns : FD_OK : Successful operation. * FD_NOT_SUPPORTED: Wrong UART number. * FD_NOT_READY : The function is called while the callback of * the readOutFunc function is activated and still * not terminated. * FD_INTERNAL_ERR : Internal problem with the hardware. * ******************************************************************************/ C_EXTERN T_FDRET UAF_GetLineState (T_fd_UartId uartNo, SYS_UWORD32 *state); /******************************************************************************* * * UAF_SetLineState * * Purpose : Sets the states of the V.24 status lines according to the bit * field of the parameter state. * * Arguments: In : uartNo: Used UART. * state : Bit field. Only the signals which are marked with * the 'set' access can be used to change the state of * the signal. * mask : Bit field with the same structure as state. Each bit * in state corresponds to a bit in mask. Settabled * bits marked by a 1 are manipulated by the driver. * Out: none * * Returns : FD_OK : Successful operation. * FD_NOT_SUPPORTED: Wrong UART number. * FD_INTERNAL_ERR : Internal problem with the hardware. * ******************************************************************************/ C_EXTERN T_FDRET UAF_SetLineState (T_fd_UartId uartNo, SYS_UWORD32 state, SYS_UWORD32 mask); /******************************************************************************* * * UAF_InterruptHandler * * Purpose : Interrupt handler. * * Arguments: In : uart_id : origin of interrupt * interrupt_status: source of interrupt * Out: none * * Returns : none * ******************************************************************************/ C_EXTERN void UAF_InterruptHandler (T_fd_UartId uart_id, SYS_UWORD8 interrupt_status); /******************************************************************************* * * UAF_CheckXEmpty * * Purpose : Checks the empty condition of the Transmitter. * * Arguments: In : uartNo: Used UART. * Out: none * * Returns : FD_OK : Empty condition OK. * FD_NOT_SUPPORTED: Wrong UART number. * FD_NOT_READY : Empty condition not OK. * FD_INTERNAL_ERR : Internal problem with the hardware. * ******************************************************************************/ C_EXTERN T_FDRET UAF_CheckXEmpty (T_fd_UartId uartNo); /******************************************************************************* * * UAF_DTRInterruptHandler * * Purpose : This function is only used on C-Sample. On this platform, the DTR * signal is controlled with an I/O. A change of state of this signal * is detected with an interrupt. This function is called when this * interrupt occurs. * * Arguments: In : none * Out: none * * Returns : none * ******************************************************************************/ void UAF_DTRInterruptHandler (void); /******************************************************************************* * * UAF_Exit * * Purpose : * * Arguments: In : uartNo: Used UART. * Out: none * * Returns : FD_OK : Successful operation. * FD_NOT_SUPPORTED: Wrong UART number. * FD_INTERNAL_ERR : Internal problem. * ******************************************************************************/ T_FDRET UAF_Exit (T_fd_UartId uartNo); #undef C_EXTERN #endif /* __UARTFAX_H__ */