FreeCalypso > hg > fc-magnetite
view cdg3/sap/udpa.pdf @ 632:d968a3216ba0
new tangomdm build target
TCS211/Magnetite built for target leonardo runs just fine on the Tango-based
Caramel board, but a more proper tangomdm build target is preferable in order
to better market these Tango modems to prospective commercial customers. The
only differences are in GPIO and MCSI config:
* MCSI is enabled in the tangomdm build config.
* GPIO 1 is loudspeaker amplifier control on Leonardo, but on Tango platforms
it can be used for anything. On Caramel boards this GPIO should be
configured as an output driving high.
* GPIO 2 needs to be configured as Calypso input on Leonardo, but on Tango
platforms it can be used for anything. On Caramel boards this GPIO should be
configured as an output, either high or low is OK.
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Sat, 04 Jan 2020 19:27:41 +0000 |
parents | c15047b3d00d |
children |
line wrap: on
line source
;******************************************************************************** ;*** File : udpa.pdf ;*** Creation : Wed Mar 11 09:58:55 CST 2009 ;*** XSLT Processor : Apache Software Foundation / http://xml.apache.org/xalan-j / supports XSLT-Ver: 1 ;*** Copyright : (c) Texas Instruments AG, Berlin Germany 2002 ;******************************************************************************** ;*** Document Type : Service Access Point Specification ;*** Document Name : udpa ;*** Document No. : 8444.103.02.006 ;*** Document Date : 2003-08-26 ;*** Document Status: BEING_PROCESSED ;*** Document Author: Jacek ;******************************************************************************** PRAGMA SRC_FILE_TIME "Thu Nov 29 09:56:38 2007" PRAGMA LAST_MODIFIED "2003-08-26" PRAGMA ID_AND_VERSION "8444.103.02.006" CONST UDPA_ENTITY_NAME_LEN 6 ; maximum length of entity name including NULL VALTAB VAL_dti_conn VAL 0 UDPA_CONNECT_DTI "Connect DTI2 to UDP" VAL 1 UDPA_DISCONNECT_DTI "Disconnect DTI2 from UDP" VALTAB VAL_link_id VAL 0 UDPA_LINK_ID_DEFAULT "Default link id" VALTAB VAL_dti_direction VAL 0 UDPA_DTI_TO_HIGHER_LAYER "DTI2 used normally" VAL 1 UDPA_DTI_TO_LOWER_LAYER "DTI2 is inverted" VALTAB VAL_cmd VAL 0 UDPA_CONFIG_UP "enable the interface" VAL 1 UDPA_CONFIG_DOWN "disable the interface" VAR dti_conn "DTI2 connect" B VAL @p_udpa - VAL_dti_conn@ VAR link_id "Link identifier" L VAL @p_udpa - VAL_link_id@ VAR dti_direction "DTI2 direction" B VAL @p_udpa - VAL_dti_direction@ VAR entity_name "name of an neighbour entity" B VAR cmd "command" B VAL @p_udpa - VAL_cmd@ ; UDPA_DTI_REQ 0x8000003B ; UDPA_DTI_CNF 0x8000403B ; UDPA_DTI_IND 0x8001403B ; UDPA_CONFIG_REQ 0x8001003B ; UDPA_CONFIG_CNF 0x8002403B PRIM UDPA_DTI_REQ 0x8000003B { dti_conn ; DTI connect entity_name [UDPA_ENTITY_NAME_LEN] ; Entity name link_id ; Link identifier dti_direction ; DTI direction } PRIM UDPA_DTI_CNF 0x8000403B { dti_conn ; DTI connect link_id ; Link identifier } PRIM UDPA_DTI_IND 0x8001403B { link_id ; link identifier } PRIM UDPA_CONFIG_REQ 0x8001003B { cmd ; Command } PRIM UDPA_CONFIG_CNF 0x8002403B { }