FreeCalypso > hg > fc-magnetite
view scripts/config-headers-new.sh @ 632:d968a3216ba0
new tangomdm build target
TCS211/Magnetite built for target leonardo runs just fine on the Tango-based
Caramel board, but a more proper tangomdm build target is preferable in order
to better market these Tango modems to prospective commercial customers. The
only differences are in GPIO and MCSI config:
* MCSI is enabled in the tangomdm build config.
* GPIO 1 is loudspeaker amplifier control on Leonardo, but on Tango platforms
it can be used for anything. On Caramel boards this GPIO should be
configured as an output driving high.
* GPIO 2 needs to be configured as Calypso input on Leonardo, but on Tango
platforms it can be used for anything. On Caramel boards this GPIO should be
configured as an output, either high or low is OK.
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Sat, 04 Jan 2020 19:27:41 +0000 |
parents | 92dbfa906f66 |
children | 8cf3029429f3 |
line wrap: on
line source
#!/bin/sh if [ -z "$TARGET" ] then echo "Error: TARGET= must be passed via environment" 1>&2 exit 1 fi if [ -z "$BUILD_DIR" ] then echo "Error: BUILD_DIR= must be passed via environment" 1>&2 exit 1 fi # The following vars will already be set when this script is invoked # from configure.sh in a production build, but the following defaulting logic # helps with manual invokation during development. if [ -z "$CHIPSET" ] then CHIPSET=10 fi export CHIPSET if [ -z "$DSP" ] then DSP=36 fi export DSP if [ -z "$RF" ] then RF=12 fi export RF if [ -z "$AMR" ] then AMR=1 fi export AMR if [ -z "$L1_DYN_DSP_DWNLD" ] then L1_DYN_DSP_DWNLD=1 fi export L1_DYN_DSP_DWNLD if [ -z "$L1_VOICE_MEMO_AMR" ] then L1_VOICE_MEMO_AMR=1 fi export L1_VOICE_MEMO_AMR if [ -z "$MELODY_E2" ] then MELODY_E2=1 fi export MELODY_E2 if [ -z "$SPEECH_RECO" ] then SPEECH_RECO=1 fi export SPEECH_RECO if [ -z "$GPRS" ] then GPRS=1 fi export GPRS if [ -z "$SRVC" ] then SRVC=1 fi export SRVC if [ -z "$ATP_STATE" ] then ATP_STATE=0 fi export ATP_STATE if [ -z "$FCHG_STATE" ] then FCHG_STATE=1 fi export FCHG_STATE if [ -z "$LCC_STATE" ] then LCC_STATE=0 fi export LCC_STATE if [ -z "$MKS_STATE" ] then MKS_STATE=0 fi export MKS_STATE if [ -z "$PWR_STATE" ] then PWR_STATE=0 fi export PWR_STATE if [ -z "$R2D_STATE" ] then R2D_STATE=1 fi export R2D_STATE if [ -z "$DSAMPLE_FULL_COLOR" ] then DSAMPLE_FULL_COLOR=1 fi export DSAMPLE_FULL_COLOR if [ -z "$TR_BAUD_CONFIG" ] then TR_BAUD_CONFIG=TR_BAUD_115200 fi export TR_BAUD_CONFIG # Derived settings only for the generation of *.cfg headers case "$RF" in 10) RF_FAM=10 RF_PA=0 RF_PG=0 ;; 12) RF_FAM=12 RF_PA=2 RF_PG=2 ;; *) echo "Error: RF=$RF setting not understood" 1>&2 exit 1 esac export RF_FAM RF_PA RF_PG case "$GPRS" in 0) L1_GPRS=0 PMODE=1 ;; 1) L1_GPRS=1 PMODE=2 ;; *) echo "Error: GPRS=$GPRS setting not understood" 1>&2 exit 1 esac export L1_GPRS PMODE if [ "$SRVC" != 0 ] then IDS=1 else IDS=0 fi export IDS # do it! set -e rm -rf $BUILD_DIR/config mkdir $BUILD_DIR/config helpers/cfg-hdr-gen scripts/cfg-template $BUILD_DIR/config scripts/make-rv-swe-hdr.sh > $BUILD_DIR/config/rv_swe.h cp targets/$TARGET.h $BUILD_DIR/config/fc-target.h