FreeCalypso > hg > fc-magnetite

view src/cs/drivers/drv_app/lcc/lcc_modulate.c @ 632:d968a3216ba0

Find changesets by keywords (author, files, the commit message), revision number or hash, or revset expression.
new tangomdm build target TCS211/Magnetite built for target leonardo runs just fine on the Tango-based Caramel board, but a more proper tangomdm build target is preferable in order to better market these Tango modems to prospective commercial customers. The only differences are in GPIO and MCSI config: * MCSI is enabled in the tangomdm build config. * GPIO 1 is loudspeaker amplifier control on Leonardo, but on Tango platforms it can be used for anything. On Caramel boards this GPIO should be configured as an output driving high. * GPIO 2 needs to be configured as Calypso input on Leonardo, but on Tango platforms it can be used for anything. On Caramel boards this GPIO should be configured as an output, either high or low is OK.
author Mychaela Falconia <falcon@freecalypso.org>
date Sat, 04 Jan 2020 19:27:41 +0000
parents 945cf7f506b2
children
line wrap: on
line source

/******************************************************************************
 * Power Task (pwr)
 * Design and coding by Svend Kristian Lindholm, skl@ti.com
 *
 * PWR SW Modulation
 *
 * $Id: pwr_modulate.c 1.1 Wed, 20 Aug 2003 10:22:37 +0200 skl $
 *
 ******************************************************************************/
#include <string.h>
#include "lcc/lcc.h"
#include "lcc/lcc_trace.h"
#include "lcc/lcc_modulate.h"
#include "lcc/lcc_cfg_i.h"
#include "lcc/lcc_cfg.h"
#include "rv/rv_defined_swe.h"
#include "abb/abb.h"

/******************************************************************************
 * Function prototypes
 ******************************************************************************/

void pwr_modulate_init(void);
void pwr_modulate_on(void);
void pwr_modulate_off(void);


#if (USE_Q401_CHG_CIRCUIT == 1)
extern T_PWR_CFG_BLOCK  *pwr_cfg;
#endif

void pwr_modulate_init(void) {
    ttw(ttr(TTrEventLow,"pwr_modulate_init(%d)" NL, 0));
    #if (USE_PWL_AS_MODULATOR == 1)
    BUZZ_LIGHT_REG |= 0x02;
    PWL_LEVEL_REG = 0xFF; // Full envelope function
    PWL_CTRL_REG  = 0x00; // No 32KHz clock
    #else
    // Set GPIO 6 HIGH
    *((volatile uint16 *) 0xfffe4806) |= 0x0020; // Enable GPIO module
    *((volatile uint16 *) 0xfffe4804) &= 0xffbf; // Set GPIO-6 = output
    *((volatile uint16 *) 0xfffe4802) |= 0x0080; // Set GPIO-6 = HIGH
    #endif
    ttw(ttr(TTrEventLow,"pwr_modulate_init(%d)" NL, 0xff));
}

void pwr_modulate_on(void) {
    ttw(ttr(TTrEventLow,"pwr_modulate_on(%d)" NL, 0));
#if (USE_Q401_CHG_CIRCUIT== 1)
    /* Program the DAC with the constant current value taken from /pwr/chg/chg<N>.cfg multiplied by k/255, where current k is in [1..255] */
    ABB_Write_Register_on_page(PAGE0, CHGREG, (pwr_cfg->data.k * pwr_cfg->chg.ichg_max) / 255);
#endif
#if (USE_Q402_CHG_CIRCUIT == 1)
    #if (USE_PWL_AS_MODULATOR == 1)
    BUZZ_LIGHT_REG |= 0x02;
    PWL_LEVEL_REG = 0xFF; // Full envelope function
    PWL_CTRL_REG  = 0x00; // No 32KHz clock
    #else
    // Use GPIO 6
    *((volatile uint16 *) 0xfffe4806) |= 0x0020; // Enable GPIO module
    *((volatile uint16 *) 0xfffe4804) &= 0xffbf; // Set GPIO-6 = output
    *((volatile uint16 *) 0xfffe4802) |= 0x0080; // Set GPIO-6 = HIGH
    #endif
#endif
    ttw(ttr(TTrEventLow,"pwr_modulate_on(%d)" NL, 0xFF));

}

void pwr_modulate_off(void) {
    ttw(ttr(TTrEventLow,"pwr_modulate_off(%d)" NL, 0));
#if (USE_Q401_CHG_CIRCUIT == 1)
    // Don't do anything - FET is fully controlled in pwr_modulate_on()
#endif
#if (USE_Q402_CHG_CIRCUIT == 1)
    #ifdef USE_PWL_AS_MODULATOR
    BUZZ_LIGHT_REG &= 0xfd;
    PWL_LEVEL_REG = 0x00; // No envelope function
    PWL_CTRL_REG  = 0x00; // No 32KHz clock
    #else
    // Use GPIO 6
    *((volatile uint16 *) 0xfffe4806) |= 0x0020; // Enable GPIO module
    *((volatile uint16 *) 0xfffe4804) &= 0xffbf; // Set GPIO-6 = output
    *((volatile uint16 *) 0xfffe4802) &= 0x007f; // Set GPIO-6 = LOW
    #endif
#endif
    ttw(ttr(TTrEventLow,"pwr_modulate_off(%d)" NL, 0xFF));
}