view src/cs/services/atp/Bti.h @ 632:d968a3216ba0

new tangomdm build target TCS211/Magnetite built for target leonardo runs just fine on the Tango-based Caramel board, but a more proper tangomdm build target is preferable in order to better market these Tango modems to prospective commercial customers. The only differences are in GPIO and MCSI config: * MCSI is enabled in the tangomdm build config. * GPIO 1 is loudspeaker amplifier control on Leonardo, but on Tango platforms it can be used for anything. On Caramel boards this GPIO should be configured as an output driving high. * GPIO 2 needs to be configured as Calypso input on Leonardo, but on Tango platforms it can be used for anything. On Caramel boards this GPIO should be configured as an output, either high or low is OK.
author Mychaela Falconia <falcon@freecalypso.org>
date Sat, 04 Jan 2020 19:27:41 +0000
parents 945cf7f506b2
children
line wrap: on
line source

/*
+-------------------------------------------------------------------+
| PROJECT: GSM-BT  (8445)            $Workfile:: Bti.h             $|
| $Author:: Mg                       $$Revision:: 26               $|
| CREATED: 06 April 2000             $Modtime:: 15.03.00 16:01     $|
+-------------------------------------------------------------------+

   MODULE  : BTI

   PURPOSE : Global definitions for the Bluetooth Interface,
             which are visible to both sides

   $Log:: /GSM/Condat/MS/SRC/BTI/Bti.h                             $
 *

*/


#ifndef BTI_H
#define BTI_H



/*
 * Conditional Compiling
 */

/*
 * Constants
 */

/* These are the addresses for the headset and the dial-up devices*/

#define HS_BD_ADDR_BYTE_0 0xbb; /*mvi@140900*/
#define HS_BD_ADDR_BYTE_1 0xbb;
#define HS_BD_ADDR_BYTE_2 0xbb;
#define HS_BD_ADDR_BYTE_3 0xbb;
#define HS_BD_ADDR_BYTE_4 0xbb;
#define HS_BD_ADDR_BYTE_5 0xbb;

#define DU_BD_ADDR_BYTE_0 0xcc; /*mvi@140900*/
#define DU_BD_ADDR_BYTE_1 0xcc;
#define DU_BD_ADDR_BYTE_2 0xcc;
#define DU_BD_ADDR_BYTE_3 0xcc;
#define DU_BD_ADDR_BYTE_4 0xcc;
#define DU_BD_ADDR_BYTE_5 0xcc;


typedef unsigned char   T_BTI_DEVICE_TYPE;
typedef unsigned short	T_BTI_SEARCH_TIME;
typedef unsigned short	T_BTI_SEARCH_BREAK;
typedef unsigned short	T_BTI_SCAN_TIME;
typedef unsigned short	T_BTI_SCAN_BREAK;
typedef unsigned char	T_BTI_SECURITY_MODE;
typedef unsigned char	T_BTI_ATTEMPTS;
typedef unsigned char	T_BTI_MAX_RING;
typedef unsigned char   T_BTI_BONDING_MODE;
typedef unsigned char   T_BTI_PARK_MODE;

typedef struct
{
	T_BTI_SEARCH_TIME	search_time;
	T_BTI_SEARCH_BREAK	search_break;
	T_BTI_SCAN_TIME		scan_time;
	T_BTI_SCAN_BREAK	scan_break;
	T_BTI_SECURITY_MODE	security_mode;
	T_BTI_ATTEMPTS		connect_attempts;
	T_BTI_MAX_RING		max_ring;
	T_BTI_PARK_MODE		park_mode;
	T_BTI_BONDING_MODE	bonding;
}T_BTI_CONFIG;

typedef unsigned char   T_BTI_RESULT;


typedef unsigned char	T_BTI_BD_ADDR;
typedef unsigned char	T_BTI_BD_NAME;
typedef unsigned char	T_BTI_PIN;

typedef unsigned char   T_BTI_ERROR_CAUSE;

typedef unsigned char   T_BTI_AUDIO_STATE;

typedef unsigned char   T_BTI_REQ_ID;

typedef unsigned char   T_BTI_RES_ID;

typedef unsigned char   T_BTI_CNF_ID;

typedef unsigned char   T_BTI_IND_ID;


#endif