FreeCalypso > hg > fc-magnetite
view src/g23m-aci/aci/aci_bat_csc.c @ 632:d968a3216ba0
new tangomdm build target
TCS211/Magnetite built for target leonardo runs just fine on the Tango-based
Caramel board, but a more proper tangomdm build target is preferable in order
to better market these Tango modems to prospective commercial customers. The
only differences are in GPIO and MCSI config:
* MCSI is enabled in the tangomdm build config.
* GPIO 1 is loudspeaker amplifier control on Leonardo, but on Tango platforms
it can be used for anything. On Caramel boards this GPIO should be
configured as an output driving high.
* GPIO 2 needs to be configured as Calypso input on Leonardo, but on Tango
platforms it can be used for anything. On Caramel boards this GPIO should be
configured as an output, either high or low is OK.
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Sat, 04 Jan 2020 19:27:41 +0000 |
parents | 53929b40109c |
children |
line wrap: on
line source
/* +----------------------------------------------------------------------------- | Project : GSM-F&D (8411) | Modul : ACI_BAT +----------------------------------------------------------------------------- | Copyright 2002 Texas Instruments Berlin, AG | All rights reserved. | | This file is confidential and a trade secret of Texas | Instruments Berlin, AG | The receipt of or possession of this file does not convey | any rights to reproduce or disclose its contents or to | manufacture, use, or sell anything it may describe, in | whole, or in part, without the specific written consent of | Texas Instruments Berlin, AG. +----------------------------------------------------------------------------- | Purpose : This BAT wrapper modul is ... | +----------------------------------------------------------------------------- */ #include "aci_all.h" /* includes prim.h, which includes p_bat.h */ #include "aci_cmh.h" /* prototypes of sAT_,qAT_,tAT_ */ #include "aci_cmd.h" #include "aci_lst.h" #include "ati_int.h" #include "aci_bat_cmh.h" /* prototypes of sBAT_,qBAT_,tBAT_ */ #include "aci_bat.h" /* +--------------------------------------------------------------------+ | PROJECT : GSM-F&D (8411) MODULE : ACI_BAT | | STATE : code ROUTINE : sBAT_PercentBAND | +--------------------------------------------------------------------+ PURPOSE : */ GLOBAL T_ACI_BAT_RSLT sBAT_PercentBAND(T_ACI_DTI_PRC_PSI *src_infos_psi, T_BAT_cmd_send *cmd) { T_ACI_BAT_RSLT ret = ACI_BAT_FAIL; T_BAT_cmd_set_percent_band *band = cmd->params.ptr_set_percent_band; TRACE_FUNCTION ("sBAT_PercentBAND()"); /* Pass the value directly as given by the BAT application */ if (band->band NEQ BAT_P_BAND_BAND_NOT_PRESENT) { ret = (T_ACI_BAT_RSLT)sAT_PercentBAND((T_ACI_CMD_SRC)src_infos_psi->srcId, (T_ACI_BAND_MODE)band->mode, (U8)band->band); } return ret; } /* +--------------------------------------------------------------------+ | PROJECT : GSM-F&D (8411) MODULE : ACI_BAT | | STATE : code ROUTINE : tBAT_PercentBAND | +--------------------------------------------------------------------+ PURPOSE : */ GLOBAL T_ACI_BAT_RSLT tBAT_PercentBAND(T_ACI_DTI_PRC_PSI *src_infos_psi, T_BAT_cmd_send *cmd) { TRACE_FUNCTION ("tBAT_PercentBAND()"); return (ACI_BAT_FAIL); } /* +--------------------------------------------------------------------+ | PROJECT : GSM-F&D (8411) MODULE : ACI_BAT | | STATE : code ROUTINE : qBAT_PercentBAND | +--------------------------------------------------------------------+ PURPOSE : */ GLOBAL T_ACI_BAT_RSLT qBAT_PercentBAND(T_ACI_DTI_PRC_PSI *src_infos_psi, T_BAT_cmd_send *cmd) { T_ACI_BAT_RSLT ret; T_BAT_cmd_response resp; T_BAT_res_que_percent_band band; TRACE_FUNCTION ("qBAT_PercentBAND()"); resp.ctrl_response = BAT_RES_QUE_PERCENT_BAND; resp.response.ptr_que_percent_band = &band; /* Band initial value should be assigned to 0 */ resp.response.ptr_que_percent_band->band = BAT_P_BAND_BAND_NOT_PRESENT; ret = (T_ACI_BAT_RSLT)qAT_PercentBAND((T_ACI_CMD_SRC)src_infos_psi->srcId, (T_ACI_BAND_MODE*)&band.mode, (U8*)&band.band); aci_bat_send(src_infos_psi, &resp); return (ret); } /* +--------------------------------------------------------------------+ | PROJECT : GSM-F&D (8411) MODULE : ACI_BAT | | STATE : code ROUTINE : qBAT_PercentCPI | +--------------------------------------------------------------------+ PURPOSE : */ GLOBAL T_ACI_BAT_RSLT qBAT_PercentCPI(T_ACI_DTI_PRC_PSI *src_infos_psi, T_BAT_cmd_send *cmd) { T_ACI_BAT_RSLT ret = ACI_BAT_FAIL; T_BAT_cmd_response resp; /* T_BAT_res_que_percent_cpi cpi; */ TRACE_FUNCTION ("qBAT_PercentCPI()"); /* resp.ctrl_response = BAT_RES_QUE_PERCENT_CPI; */ /* hmm, do not know which ACI function to call ! */ aci_bat_send(src_infos_psi, &resp); return (ret); } /* +--------------------------------------------------------------------+ | PROJECT : GSM-F&D (8411) MODULE : ACI_BAT | | STATE : code ROUTINE : qBAT_PercentCNAP | +--------------------------------------------------------------------+ PURPOSE : */ GLOBAL T_ACI_BAT_RSLT qBAT_PercentCNAP(T_ACI_DTI_PRC_PSI *src_infos_psi, T_BAT_cmd_send *cmd) { T_ACI_BAT_RSLT ret; T_BAT_cmd_response resp; T_BAT_res_que_percent_cnap cnap; TRACE_FUNCTION ("qBAT_PercentCNAP()"); resp.ctrl_response = BAT_RES_QUE_PERCENT_CNAP; resp.response.ptr_que_percent_cnap = &cnap; ret = (T_ACI_BAT_RSLT)qAT_PercentCNAP((T_ACI_CMD_SRC)src_infos_psi->srcId); aci_bat_send(src_infos_psi, &resp); return (ret); } /* +--------------------------------------------------------------------+ | PROJECT : GSM-F&D (8411) MODULE : ACI_BAT | | STATE : code ROUTINE : sBAT_PercentALS | +--------------------------------------------------------------------+ PURPOSE : */ GLOBAL T_ACI_BAT_RSLT sBAT_PercentALS(T_ACI_DTI_PRC_PSI *src_infos_psi, T_BAT_cmd_send *cmd) { T_ACI_BAT_RSLT ret = ACI_BAT_FAIL; T_ACI_ALS_MOD ALSmode; TRACE_FUNCTION ("sBAT_PercentALS()"); #ifndef _SIMULATION_ /* mapping for SAP BAT %ALS values according to 8415.052.doc */ switch( cmd->params.ptr_set_percent_als->mode ) { case BAT_P_ALS_MOD_SPEECH: ALSmode = ALS_MOD_SPEECH; break; case BAT_P_ALS_MOD_AUX_SPEECH: ALSmode = ALS_MOD_AUX_SPEECH; break; default: cmdCmeError(CME_ERR_OpNotSupp); return (ACI_BAT_FAIL); } #else /* if SIMULATION */ ALSmode = cmd->params.ptr_set_percent_als->mode; #endif /* SIMULATION */ ret = (T_ACI_BAT_RSLT)sAT_PercentALS((T_ACI_CMD_SRC)src_infos_psi->srcId, ALSmode); return (ret); } /* +--------------------------------------------------------------------+ | PROJECT : GSM-F&D (8411) MODULE : ACI_BAT | | STATE : code ROUTINE : tBAT_PercentALS | +--------------------------------------------------------------------+ PURPOSE : */ GLOBAL T_ACI_BAT_RSLT tBAT_PercentALS (T_ACI_DTI_PRC_PSI *src_infos_psi, T_BAT_cmd_send *cmd) { TRACE_FUNCTION ("tBAT_PercentALS()"); return (ACI_BAT_FAIL); } /* +--------------------------------------------------------------------+ | PROJECT : GSM-F&D (8411) MODULE : ACI_BAT | | STATE : code ROUTINE : qBAT_PercentALS | +--------------------------------------------------------------------+ PURPOSE : */ GLOBAL T_ACI_BAT_RSLT qBAT_PercentALS(T_ACI_DTI_PRC_PSI *src_infos_psi, T_BAT_cmd_send *cmd) { T_ACI_BAT_RSLT ret; T_BAT_cmd_response resp; T_BAT_res_que_percent_als als; T_ACI_ALS_MOD als_aci_mode; TRACE_FUNCTION ("qBAT_PercentALS()"); resp.ctrl_response = BAT_RES_QUE_PERCENT_ALS; resp.response.ptr_que_percent_als = &als; ret = (T_ACI_BAT_RSLT)qAT_PercentALS((T_ACI_CMD_SRC)src_infos_psi->srcId,&als_aci_mode); switch(als_aci_mode) { case ALS_MOD_SPEECH: als.mode = BAT_P_ALS_MOD_SPEECH; break; case ALS_MOD_AUX_SPEECH: als.mode = BAT_P_ALS_MOD_AUX_SPEECH; break; default: cmdCmeError(CME_ERR_OpNotSupp); return (ACI_BAT_FAIL); } aci_bat_send(src_infos_psi, &resp); return (ret); } /* +--------------------------------------------------------------------+ | PROJECT : GSM-F&D (8411) MODULE : ACI_BAT | | STATE : code ROUTINE : sBAT_PercentPPP | +--------------------------------------------------------------------+ PURPOSE : */ #if defined(FF_WAP) || defined(FF_PPP) || defined(FF_SAT_E) GLOBAL T_ACI_BAT_RSLT sBAT_PercentPPP(T_ACI_DTI_PRC_PSI *src_infos_psi, T_BAT_cmd_send *cmd) { T_ACI_BAT_RSLT ret; TRACE_FUNCTION ("sBAT_PercentPPP()"); ret = (T_ACI_BAT_RSLT)sAT_PercentPPP((T_ACI_CMD_SRC)src_infos_psi->srcId, (T_ACI_PPP_PROT)cmd->params.ptr_set_percent_ppp->authprot, (CHAR *)cmd->params.ptr_set_percent_ppp->user, (CHAR *)cmd->params.ptr_set_percent_ppp->password, (T_ACI_PPP_CON)cmd->params.ptr_set_percent_ppp->conn_type); return (ret); } /* +--------------------------------------------------------------------+ | PROJECT : GSM-F&D (8411) MODULE : ACI_BAT | | STATE : code ROUTINE : qBAT_PercentPPP | +--------------------------------------------------------------------+ PURPOSE : */ GLOBAL T_ACI_BAT_RSLT qBAT_PercentPPP(T_ACI_DTI_PRC_PSI *src_infos_psi, T_BAT_cmd_send *cmd) { T_ACI_BAT_RSLT ret = ACI_BAT_FAIL; T_BAT_cmd_response resp; T_BAT_res_que_percent_ppp ppp; TRACE_FUNCTION ("qBAT_PercentPPP()"); resp.ctrl_response = BAT_RES_QUE_PERCENT_PPP; resp.response.ptr_que_percent_ppp = &ppp; ret = (T_ACI_BAT_RSLT) qAT_PercentPPP(src_infos_psi->srcId, (ULONG*)&ppp.ipaddr, (ULONG*)&ppp.dns1,(ULONG*)&ppp.dns2); aci_bat_send(src_infos_psi, &resp); return (ret); } #endif /* defined(FF_WAP) || defined(FF_PPP) || defined(FF_SAT_E) */