FreeCalypso > hg > fc-magnetite
view src/g23m-gsm/dl/cus_dl.h @ 632:d968a3216ba0
new tangomdm build target
TCS211/Magnetite built for target leonardo runs just fine on the Tango-based
Caramel board, but a more proper tangomdm build target is preferable in order
to better market these Tango modems to prospective commercial customers. The
only differences are in GPIO and MCSI config:
* MCSI is enabled in the tangomdm build config.
* GPIO 1 is loudspeaker amplifier control on Leonardo, but on Tango platforms
it can be used for anything. On Caramel boards this GPIO should be
configured as an output driving high.
* GPIO 2 needs to be configured as Calypso input on Leonardo, but on Tango
platforms it can be used for anything. On Caramel boards this GPIO should be
configured as an output, either high or low is OK.
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Sat, 04 Jan 2020 19:27:41 +0000 |
parents | 27a4235405c6 |
children |
line wrap: on
line source
/* +----------------------------------------------------------------------------- | Project : | Modul : +----------------------------------------------------------------------------- | Copyright 2002 Texas Instruments Berlin, AG | All rights reserved. | | This file is confidential and a trade secret of Texas | Instruments Berlin, AG | The receipt of or possession of this file does not convey | any rights to reproduce or disclose its contents or to | manufacture, use, or sell anything it may describe, in | whole, or in part, without the specific written consent of | Texas Instruments Berlin, AG. +----------------------------------------------------------------------------- | Purpose : Custom dependent definitions for DL of the | mobile station | | Use this header for definitions to integrate the | protocol stack entity DL in your target system ! +----------------------------------------------------------------------------- */ #ifndef CUS_DL_H #define CUS_DL_H /*==== CONSTANTS ==================================================*/ /* * TIMER_VALUES * * Description : The constants define the timer values * for the DL timer T200 depending on the various * channel types and service access point identifiers. * Value 1 means timeout, Value 0 means timer is stopped */ #define T200_ACTIVE 2 #define T200_EXPIRED 1 #define T200_STOPPED 0 #define T200_SDCCH_SAPI_0_CNT (T200_EXPIRED + 1) #define T200_FACCH_SAPI_0_CNT_FR (T200_EXPIRED + 9) #define T200_FACCH_SAPI_0_CNT_HR (T200_EXPIRED + 5) #define T200_SDCCH_SAPI_3_CNT (T200_EXPIRED + 3) #define T200_SACCH_SAPI_3_CNT (T200_EXPIRED + 4) /* * PRIMITIVE SIZES * * Description : The primitive size of PH_DATA_REQ depends on the * used channel. It is defined separately to achieve * an optimum of transmitted bytes to physical layer. * The default value which is defined here is calculated * without any alignment bits. * E.g. SACCH N201 = 18 * l1 header = 2 * l2 header = 3 * sdu offset = 2 * sdu length = 2 * ch_type = 1 * dummy = 1 * ----------------- * total = 29 * */ #define SACCH_PRIM_SIZE 29 #define SDCCH_PRIM_SIZE 29 #define FACCH_PRIM_SIZE 29 /* * MAX_QUEUED_MESSAGES * * Description : The constant define the maximum number of * stored layer 3 messages in data link layer. */ #define MAX_QUEUED_MESSAGES 10 /* * VERSION * * Description : The constants define the type and the value * of a version identification. The version * is part of the monitor struct. */ #define T_VERSION char #define VERSION_DL "DL 1.0" /* * VSI_CALLER * * Description : For multithread applications the constant VSI_CALLER * must be defined to identify the calling thread of the * VSI-Interface. This must be done correponding to the * type of T_VSI_CALLER in VSI.H. The comma symbol is * neccessary because the vsi-functions are called * like this vsi_xxx (VSI_CALLER par2, par3 ...) */ #if defined (NEW_FRAME) #define VSI_CALLER dl_handle, #define VSI_CALLER_SINGLE dl_handle #else #ifdef OPTION_MULTITHREAD #define VSI_CALLER DL_NAME, #define VSI_CALLER_SINGLE DL_NAME #else #define VSI_CALLER #define VSI_CALLER_SINGLE #endif #endif #endif