FreeCalypso > hg > fc-magnetite
view cdg-hybrid/cdginc/m_t30.val @ 680:ee3ac8c617cb
armio.c: set GPIO2 output high initially
On TI-canonical platforms GPIO2 is DCD modem control output. In TI's
original code the AI_InitIOConfig() function called from Init_Target()
would configure GPIO2 as an output and set the initial output value to
low, but then the init code in uartfax.c called from Init_Serial_Flows()
would immediately change it to high, corresponding to DCD not asserted.
The result is a momentary asserted-state glitch on the DCD output.
The present change eliminates this glitch, setting DCD output to
not-asserted initially like it should be.
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Thu, 25 Jun 2020 03:17:43 +0000 |
parents | e7a67accfad9 |
children |
line wrap: on
line source
/* +--------------------------------------------------------------------------+ | PROJECT : PROTOCOL STACK | | FILE : m_t30.val | | SOURCE : "msg\t30.mdf" | | LastModified : "2000-02-04" | | IdAndVersion : "8411.620.98.101" | | SrcFileTime : "Wed Nov 28 10:21:26 2007" | | Generated by CCDGEN_2.5.5A on Fri Oct 14 21:41:52 2016 | | !!DO NOT MODIFY!!DO NOT MODIFY!!DO NOT MODIFY!! | +--------------------------------------------------------------------------+ */ /* PRAGMAS * PREFIX : NONE * COMPATIBILITY_DEFINES : NO (require PREFIX) * ALWAYS_ENUM_IN_VAL_FILE: NO * ENABLE_GROUP: NO * CAPITALIZE_TYPENAME: NO */ #ifndef M_T30_VAL #define M_T30_VAL #define CDG_ENTER__M_T30_VAL #define CDG_ENTER__FILENAME _M_T30_VAL #define CDG_ENTER__M_T30_VAL__FILE_TYPE CDGINC #define CDG_ENTER__M_T30_VAL__LAST_MODIFIED _2000_02_04 #define CDG_ENTER__M_T30_VAL__ID_AND_VERSION _8411_620_98_101 #define CDG_ENTER__M_T30_VAL__SRC_FILE_TIME _Wed_Nov_28_10_21_26_2007 #include "CDG_ENTER.h" #undef CDG_ENTER__M_T30_VAL #undef CDG_ENTER__FILENAME /* * Value constants for VAL_v8 */ #define v8_not_avail (0x0) /* V.8 is not available */ #define v8_avail (0x1) /* V.8 is available */ /* * Value constants for VAL_n_byte */ #define NB_256_BYTES (0x0) /* 256 octets preferred in ECM */ #define NB_64_BYTES (0x1) /* 64 octets preferred in ECM */ /* * Value constants for VAL_ready_tx_fax */ #define RTF_NO_TX_RDY (0x0) /* not ready to transmit a facsimile document */ #define RTF_TX_RDY (0x1) /* ready to transmit a facsimile document */ /* * Value constants for VAL_rec_fax_op */ #define RFO_NO_RX_RDY (0x0) /* not ready to receive a facsimile document */ #define RFO_RX_RDY (0x1) /* ready to receive a facsimile document */ /* * Value constants for VAL_data_sig_rate */ #define VAL_DATA_SIG_RATE___DEF (0x0) /* undefined signalling rate */ #define DSR_2400_V27 (0x0) /* signalling rate 2400 bps V.27 ter */ #define DSR_4800_V27 (0x4) /* signalling rate 4800 bps V.27 ter */ #define DSR_7200_V29 (0xc) /* signalling rate 7200 bps V.29 */ #define DSR_7200_V17 (0xd) /* signalling rate 7200 bps V.17 */ #define DSR_9600_V29 (0x8) /* signalling rate 9600 bps V.29 */ #define DSR_9600_V17 (0x9) /* signalling rate 9600 bps V.17 */ #define DSR_12000_V17 (0x5) /* signalling rate 12000 bps V.17 */ #define DSR_14000_V17 (0x1) /* signalling rate 14400 bps V.19 */ /* * Value constants for VAL_R8_lines_pels */ #define R8LP_R8_ONLY (0x0) /* vertical resolution is specified by R8 only */ #define R8LP_R8_EXTENDED (0x1) /* vertical resolution is specified not only by R8 */ /* * Value constants for VAL_two_dim_coding */ #define TDC_NO_2D_CODING (0x0) /* no 2D T.4 coding */ #define TDC_2D_CODING (0x1) /* 2D T.4 coding */ /* * Value constants for VAL_rec_width */ #define RW_WIDTH_215_MM (0x0) /* Scan line length of 215 mm */ #define RW_WIDTH_303_MM (0x1) /* Scan line length of 215, 255 and 303 mm */ #define RW_WIDTH_255_MM (0x2) /* Scan line length of 215 and 255 mm */ #define RW_WIDTH_INVALID (0x3) /* Invalid scan line length */ /* * Value constants for VAL_max_rec_len */ #define MRL_A4 (0x0) /* Maximum recording length A4 (297 mm) */ #define MRL_UNLIMITED (0x1) /* Unlimited recording length */ #define MRL_B4 (0x2) /* Maximum recording length B4 (364 mm) */ #define MRL_INVALID (0x3) /* Invalid recording length */ /* * Value constants for VAL_min_scan_time */ #define MST_20_MS (0x0) /* 20 ms at 3.85 1/mm: T7.7 = T3.85 */ #define MST_40_MS (0x1) /* 40 ms at 3.85 1/mm: T7.7 = T3.85 */ #define MST_10_MS (0x2) /* 10 ms at 3.85 1/mm: T7.7 = T3.85 */ #define MST_5_MS (0x3) /* 5 ms at 3.85 1/mm: T7.7 = T3.85 */ #define MST_10_MS_HALF (0x4) /* 10 ms at 3.85 1/mm: T7.7 = 1/2 T3.85 */ #define MST_20_MS_HALF (0x5) /* 20 ms at 3.85 1/mm: T7.7 = 1/2 T3.85 */ #define MST_40_MS_HALF (0x6) /* 40 ms at 3.85 1/mm: T7.7 = 1/2 T3.85 */ #define MST_0_MS (0x7) /* 0 ms at 3.85 1/mm: T7.7 = T3.85 */ /* * Value constants for VAL_uncomp_mode */ #define UCM_COMPRESSED (0x0) /* T.4 data (can be send)/(are) in compressed mode */ #define UCM_UNCOMPRESSED (0x1) /* T.4 data (can be send)/(are) in uncompressed mode */ /* * Value constants for VAL_err_corr_mode */ #define ECM_OFF (0x0) /* Error correction mode is not possible/off */ #define ECM_ON (0x1) /* Error correction mode is possible/on */ /* * Value constants for VAL_t6_coding */ #define T6_CODING_OFF (0x0) /* T.6 coding is not possible/off */ #define T6_CODING_ON (0x1) /* T.6 coding is possible/on */ /* * Value constants for VAL_R8_lines */ #define R8_LINES_OFF (0x0) /* R8 x 15.4 lines/mm is not possible/off */ #define R8_LINES_ON (0x1) /* R8 x 15.4 lines/mm is possible/on */ /* * Value constants for VAL_r_300_pels */ #define R300_PELS_OFF (0x0) /* Res 300 x 300 pels /25.4 mm is not possible/off */ #define R300_PELS_ON (0x1) /* Res 300 x 300 pels /25.4 mm is possible/on */ /* * Value constants for VAL_R16_lines_pels */ #define R16_LINES_PELS_OFF (0x0) /* R16 x 15.4 lines/mm and/or 400 x 400 pels/24.4 mm mode is not possible/off */ #define R16_LINES_PELS_ON (0x1) /* R16 x 15.4 lines/mm and/or 400 x 400 pels/24.4 mm mode is possible/on */ /* * Value constants for VAL_i_res_pref */ #define IRP_NO_INCH_BASED (0x0) /* Inch-based resolution not preferred */ #define IRP_INCH_BASED (0x1) /* Inch-based resolution preferred */ /* * Value constants for VAL_m_res_pref */ #define IRP_NO_METRIC_BASED (0x0) /* Metric-based resolution not preferred */ #define IRP_METRIC_BASED (0x1) /* Metric-based resolution preferred */ /* * Value constants for VAL_min_scan_time_hr */ #define MST_T154_EQ_T77 (0x0) /* T15.4 = T7.7 */ #define MST_T154_EQ_HALF_T77 (0x1) /* T15.4 = 0.5 x T7.7 */ /* * Value constants for VAL_sel_polling */ #define SEP_NO_POLLING (0x0) /* Selective polling not possible */ #define SEP_POLLING (0x1) /* Selective polling possible */ /* * Value constants for VAL_subaddr */ #define SA_NO_SUBADDRESSING (0x0) /* Sub-addressing is not possible/intended */ #define SA_SUBADDRESSNIG (0x1) /* Sub-addressing is possible/intended */ /* * Value constants for VAL_password */ #define PW_NO_PASSWORD (0x0) /* Password checking is not possible/intended */ #define PW_PASSWORD (0x1) /* Password checking is possible/intended */ /* * Value constants for VAL_ready_tx_doc */ #define RTD_TX_READY (0x0) /* Ready to transmit a data file */ #define RTD_NOT_TX_READY (0x1) /* Not ready to transmit a data file */ /* * Value constants for VAL_bft */ #define BFT_NO_BIN_FILE_TX (0x0) /* Not possible/intended to transmit a binary file */ #define BFT_BIN_FILE_TX (0x1) /* Possibility/intention to transmit a binary file */ /* * Value constants for VAL_dtm */ #define DTM_NO_DOC_TX_MODE (0x0) /* Not possible/intended to perform the DTM */ #define DTM_DOC_TX_MODE (0x1) /* Possibility/intention to perform the DTM */ /* * Value constants for VAL_edi */ #define EDI_NO_ELEC_DATA_XCHNG (0x0) /* Not possible/intended to perform EDI */ #define EDI_ELEC_DATA_XCHNG (0x1) /* Possibility/intention to perform EDI */ /* * Value constants for VAL_btm */ #define BTM_NO_BASIC_TRANS_MODE (0x0) /* Not possible/intended to perform the BTM */ #define BTM_BASIC_TRANS_MODE (0x1) /* Possibility/intention to perform the BTM */ /* * Value constants for VAL_ready_tx_mixed */ #define RTM_NO_READY_TX_MIXED (0x0) /* Not ready to transmit a character or mixed mode document */ #define RTM_READY_TX_MIXED (0x1) /* Ready to transmit a character or mixed mode document */ /* * Value constants for VAL_char_mode */ #define CM_NO_CHARACTER_MODE (0x0) /* Not possible/intended to perform the character mode */ #define CM_CHARACTER_MODE (0x1) /* Possibility/intention to perform the character mode */ /* * Value constants for VAL_mixed_mode */ #define MM_NO_MIXED_MODE (0x0) /* Not possible/intended to perform the mixed mode */ #define MM_MIXED_MODE (0x1) /* Possibility/intention to perform the mixed mode */ /* * Value constants for VAL_proc_mode_26 */ #define PM_NO_PROC_MODE_26 (0x0) /* Not possible/intended to perform the processable mode 26 */ #define PM_PROC_MODE_26 (0x1) /* Possibility/intention to perform the processable mode 26 */ /* * Value constants for VAL_dig_network_cap */ #define DNC_NO_DIGITAL_NETWORK (0x0) /* Terminal is not on a digital network */ #define DNC_DIGITAL_NETWORK (0x1) /* Terminal is on a digital network */ /* * Value constants for VAL_duplex */ #define DUP_HALF_DUPLEX (0x0) /* Operate in half duplex mode only */ #define DUP_FULL_DUPLEX (0x1) /* Operate in full-duplex or half duplex mode */ /* * Value constants for VAL_jpeg */ #define JPG_NO_CODING (0x0) /* Not able/intent to code documents in JPEG */ #define JPG_CODING (0x1) /* Able/intent to code documents in JPEG */ /* * Value constants for VAL_full_colour */ #define FC_NO_FULL_COLOR_MODE (0x0) /* Not able/intent to work in full colour mode */ #define FC_FULL_COLOR_MODE (0x1) /* Able/intent to work in full colour mode */ /* * Value constants for VAL_r_12_bits_pel_comp */ #define BPP_8_BITS_PER_PEL (0x0) /* Images must/are digitised with 8 bits/pel */ #define BPP_12_BITS_PER_PEL (0x1) /* Images may be/are digitised with up to 12 bits/pel */ /* * Value constants for VAL_no_subsamp */ #define NS_USE_4_1_1_SUB (0x0) /* Use the 4:1:1 sub-sampling ratio for the chrominance components in the image data */ #define NS_NO_SUBSAMPLING (0x1) /* Use no sub-sampling ratio for the chrominance components in the image data */ /* * Value constants for VAL_cust_illum */ #define CI_USE_D50_ILLUM (0x0) /* Only the standard D50 illuminant for colour images supported/used */ #define CI_CUSTOM_ILLUM (0x1) /* Standard D50 illuminant and other illuminants are supported/used for colour images */ /* * Value constants for VAL_cust_gamut */ #define CG_STD_GAMUT_RNG (0x0) /* Only the default gamut range for colour images supported/used */ #define CG_CUST_GAMUT_RNG (0x1) /* Other gamut ranges are supported/used for colour images */ /* * Value constants for VAL_na_letter */ #define NLT_NO_NORTH_AMERICAN_LETTER (0x0) /* No North American Letter format is supported/used */ #define NLT_NORTH_AMERICAN_LETTER (0x1) /* No North American Letter format is supported/used */ /* * Value constants for VAL_na_legal */ #define NLG_NO_NORTH_AMERICAN_LEGAL (0x0) /* No North American Legal format is supported/used */ #define NLG_NORTH_AMERICAN_LEGAL (0x1) /* No North American Legal format is supported/used */ /* * Value constants for VAL_sing_prog_seq_coding_basic */ #define SPG_NO_SINGLE_PROG_BASIC (0x0) /* No single-progression sequential coding basic is supported/used */ #define SPG_SINGLE_PROG_BASIC (0x1) /* Single-progression sequential coding basic is supported/used */ /* * Value constants for VAL_sing_prog_seq_coding_L0 */ #define SPG_NO_SINGLE_PROG_L0 (0x0) /* No single-progression sequential coding optional L0 is supported/used */ #define SPG_SINGLE_PROG_L0 (0x1) /* Single-progression sequential coding optional L0 is supported/used */ /* * Value constants for VAL_frame_size */ #define FS_256_OCTETS (0x0) /* Frame size of 256 octets is used if ECM is active */ #define FS_64_OCTETS (0x1) /* Frame size of 64 octets is used if ECM is active */ /* * Value constants for VAL_resolution_type */ #define RT_METRIC_BASED (0x0) /* Metric based resolution */ #define RT_INCH_BASED (0x1) /* Inch based resolution */ /* * Value constants for VAL_huffman_tables */ #define HT_NO_HUFFMAN_TABLES (0x0) /* No default Huffman tables used */ #define HT_HUFFMAN_TABLES (0x1) /* Default Huffman tables used */ /* * user defined constants */ #define MAX_NSF_LEN (0x2d0) #include "CDG_LEAVE.h" #endif