FreeCalypso > hg > fc-magnetite
view cdg-hybrid/cdginc/p_rrlc.val @ 680:ee3ac8c617cb
armio.c: set GPIO2 output high initially
On TI-canonical platforms GPIO2 is DCD modem control output. In TI's
original code the AI_InitIOConfig() function called from Init_Target()
would configure GPIO2 as an output and set the initial output value to
low, but then the init code in uartfax.c called from Init_Serial_Flows()
would immediately change it to high, corresponding to DCD not asserted.
The result is a momentary asserted-state glitch on the DCD output.
The present change eliminates this glitch, setting DCD output to
not-asserted initially like it should be.
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Thu, 25 Jun 2020 03:17:43 +0000 |
parents | e7a67accfad9 |
children |
line wrap: on
line source
/* +--------------------------------------------------------------------------+ | PROJECT : PROTOCOL STACK | | FILE : p_rrlc.val | | SOURCE : "sap\rrlc.pdf" | | LastModified : "2002-10-11" | | IdAndVersion : "8443.101.02.008" | | SrcFileTime : "Thu Nov 29 09:52:52 2007" | | Generated by CCDGEN_2.5.5A on Fri Oct 14 21:41:52 2016 | | !!DO NOT MODIFY!!DO NOT MODIFY!!DO NOT MODIFY!! | +--------------------------------------------------------------------------+ */ /* PRAGMAS * PREFIX : NONE * COMPATIBILITY_DEFINES : NO (require PREFIX) * ALWAYS_ENUM_IN_VAL_FILE: NO * ENABLE_GROUP: NO * CAPITALIZE_TYPENAME: NO */ #ifndef P_RRLC_VAL #define P_RRLC_VAL #define CDG_ENTER__P_RRLC_VAL #define CDG_ENTER__FILENAME _P_RRLC_VAL #define CDG_ENTER__P_RRLC_VAL__FILE_TYPE CDGINC #define CDG_ENTER__P_RRLC_VAL__LAST_MODIFIED _2002_10_11 #define CDG_ENTER__P_RRLC_VAL__ID_AND_VERSION _8443_101_02_008 #define CDG_ENTER__P_RRLC_VAL__SRC_FILE_TIME _Thu_Nov_29_09_52_52_2007 #include "CDG_ENTER.h" #undef CDG_ENTER__P_RRLC_VAL #undef CDG_ENTER__FILENAME /* * Value constants for VAL_cause */ #define LCS_OK (0x0) /* no error */ #define LCS_WRONG_BTS (0xa) /* Serving Cell BTS differs from Reference BTS */ #define LCS_HANDOVER (0x14) /* handover occured during Position Measurement procedure */ /* * Value constants for VAL_sb_flag */ #define EOTD_INVALID (0x0) /* invalid data */ #define EOTD_VALID (0x1) /* valid data */ /* * Value constants for VAL_eotd_mode */ #define EOTD_IDLE (0x0) /* Idle mode */ #define EOTD_DEDIC (0x1) /* Dedicated or packet mode */ /* * Value constants for VAL_exp_otd */ /* * Value constants for VAL_fn */ #define FNMAX (0x297000) /* max Frame Number + 1 (26*51*2048) */ /* * Value constants for VAL_mfrm_offset */ /* * Value constants for VAL_otd_type */ #define ROUGH_RTD (0x0) /* only rough RTD has been provided by the NW */ #define EXPECTED_OTD (0x1) /* only expectedOTD has been provided by the NW */ #define BOTH_OTD (0x2) /* Both OTD / RTD types have been provided by the NW */ /* * Value constants for VAL_rough_rtd */ /* * Value constants for VAL_tav */ #define TA_NOT_AVAIL (0xff) /* no Timing Advance in Idle Mode */ /* * Value constants for VAL_uncertainty */ #define UNC_MAX_2BIT (0x0) /* uncertainty in bits. 0 - 2 bits */ #define UNC_MAX_4BIT (0x1) /* uncertainty in bits. 3 - 4 bits */ #define UNC_MAX_8BIT (0x2) /* uncertainty in bits. 5 - 8 bits */ #define UNC_MAX_12BIT (0x3) /* uncertainty in bits. 9 - 12 bits */ #define UNC_MAX_16BIT (0x4) /* uncertainty in bits. 13 - 16 bits */ #define UNC_MAX_22BIT (0x5) /* uncertainty in bits. 17 - 22 bits */ #define UNC_MAX_30BIT (0x6) /* uncertainty in bits. 23 - 30 bits */ #define UNC_GT_30BIT (0x7) /* uncertainty in bits. > 30 bits */ /* * user defined constants */ #define MAX_NCELL_EOTD_L1 (0xc) #define MAX_NCELL_EOTD (0xf) #define MAX_NCELL_EOTD_SI (0x20) #define XCOR_NO (0x12) #include "CDG_LEAVE.h" #endif