FreeCalypso > hg > fc-magnetite
view cdg-hybrid/cdginc/p_t30.h @ 680:ee3ac8c617cb
armio.c: set GPIO2 output high initially
On TI-canonical platforms GPIO2 is DCD modem control output. In TI's
original code the AI_InitIOConfig() function called from Init_Target()
would configure GPIO2 as an output and set the initial output value to
low, but then the init code in uartfax.c called from Init_Serial_Flows()
would immediately change it to high, corresponding to DCD not asserted.
The result is a momentary asserted-state glitch on the DCD output.
The present change eliminates this glitch, setting DCD output to
not-asserted initially like it should be.
| author | Mychaela Falconia <falcon@freecalypso.org> |
|---|---|
| date | Thu, 25 Jun 2020 03:17:43 +0000 |
| parents | e7a67accfad9 |
| children |
line wrap: on
line source
/* +--------------------------------------------------------------------------+ | PROJECT : PROTOCOL STACK | | FILE : p_t30.h | | SOURCE : "sap\t30.pdf" | | LastModified : "2002-04-23" | | IdAndVersion : "8411.104.98.312" | | SrcFileTime : "Thu Nov 29 09:54:28 2007" | | Generated by CCDGEN_2.5.5A on Fri Oct 14 21:41:52 2016 | | !!DO NOT MODIFY!!DO NOT MODIFY!!DO NOT MODIFY!! | +--------------------------------------------------------------------------+ */ /* PRAGMAS * PREFIX : NONE * COMPATIBILITY_DEFINES : NO (require PREFIX) * ALWAYS_ENUM_IN_VAL_FILE: NO * ENABLE_GROUP: NO * CAPITALIZE_TYPENAME: NO */ #ifndef P_T30_H #define P_T30_H #define CDG_ENTER__P_T30_H #define CDG_ENTER__FILENAME _P_T30_H #define CDG_ENTER__P_T30_H__FILE_TYPE CDGINC #define CDG_ENTER__P_T30_H__LAST_MODIFIED _2002_04_23 #define CDG_ENTER__P_T30_H__ID_AND_VERSION _8411_104_98_312 #define CDG_ENTER__P_T30_H__SRC_FILE_TIME _Thu_Nov_29_09_54_28_2007 #include "CDG_ENTER.h" #undef CDG_ENTER__P_T30_H #undef CDG_ENTER__FILENAME #include "p_t30.val" #ifndef __T_dis__ #define __T_dis__ /* * digital identification signal * CCDGEN:WriteStruct_Count==3074 */ typedef struct { U8 v8; /*< 0: 1> V.8 capabilities */ U8 n_byte; /*< 1: 1> no. of octets preferred */ U8 ready_tx_fax; /*< 2: 1> ready to transmit a facsimile document (polling) */ U8 rec_fax_op; /*< 3: 1> receiver fax operation */ U8 data_sig_rate; /*< 4: 1> data signalling rate */ U8 R8_lines_pels; /*< 5: 1> R8*7.7 lines/mm and/or 200 x 200 pels/25.4 mm */ U8 two_dim_coding; /*< 6: 1> two-dimensional coding */ U8 rec_width; /*< 7: 1> recording-width */ U8 max_rec_len; /*< 8: 1> maximum recording length */ U8 min_scan_time; /*< 9: 1> minimum scan line time at the receiver */ U8 uncomp_mode; /*< 10: 1> uncompressed mode */ U8 err_corr_mode; /*< 11: 1> error correction mode */ U8 frame_size; /*< 12: 1> frame size */ U8 t6_coding; /*< 13: 1> T.6 coding */ U8 R8_lines; /*< 14: 1> R8*15.4 lines/mm */ U8 r_300_pels; /*< 15: 1> 300*300 pels/25.4 mm */ U8 R16_lines_pels; /*< 16: 1> R16*15.4 lines/mm and/or 400*400 pels/25.4 mm */ U8 resolution_type; /*< 17: 1> resolution type selection */ U8 i_res_pref; /*< 18: 1> inch based resolution preferred */ U8 m_res_pref; /*< 19: 1> metric-based resolution preferred */ U8 min_scan_time_hr; /*< 20: 1> minimum scan line time for higher resolutions */ U8 sel_polling; /*< 21: 1> selective polling */ U8 subaddr; /*< 22: 1> subaddressing */ U8 password; /*< 23: 1> password */ U8 ready_tx_doc; /*< 24: 1> ready to transmit a data file (polling) */ U8 bft; /*< 25: 1> Binary File Transfer (BFT) */ U8 dtm; /*< 26: 1> Document Transfer Mode (DTM) */ U8 edi; /*< 27: 1> Electronic Data Interchange (EDI) */ U8 btm; /*< 28: 1> Basic Transfer Mode (BTM) */ U8 ready_tx_mixed; /*< 29: 1> ready to transmit a character or mixed mode document (polling) */ U8 char_mode; /*< 30: 1> character mode */ U8 mixed_mode; /*< 31: 1> mixed mode (Annex E/T.4) */ U8 proc_mode_26; /*< 32: 1> processable mode 26) */ U8 dig_network_cap; /*< 33: 1> digital network capability */ U8 duplex; /*< 34: 1> duplex and half duplex capabilities */ U8 jpeg; /*< 35: 1> JPEG coding */ U8 full_colour; /*< 36: 1> full colour mode */ U8 huffman_tables; /*< 37: 1> preferred Huffman tables */ U8 r_12_bits_pel_comp; /*< 38: 1> 12 bits/pel component */ U8 no_subsamp; /*< 39: 1> no subsampling */ U8 cust_illum; /*< 40: 1> custom illuminant */ U8 cust_gamut; /*< 41: 1> custom gamut range */ U8 na_letter; /*< 42: 1> North American Letter (215.9*279.4 mm) */ U8 na_legal; /*< 43: 1> North American Legal (215.9*355.6 mm) */ U8 sing_prog_seq_coding_basic; /*< 44: 1> single-progression sequential coding basic */ U8 sing_prog_seq_coding_L0; /*< 45: 1> single-progression sequential coding optional L0 */ U8 _align0; /*< 46: 1> alignment */ U8 _align1; /*< 47: 1> alignment */ } T_dis; #endif /* * digital transmit command * CCDGEN:WriteStruct_Count==3075 */ #ifndef __T_dtc__ #define __T_dtc__ typedef T_dis T_dtc; #endif /* * digital command signal * CCDGEN:WriteStruct_Count==3076 */ #ifndef __T_dcs__ #define __T_dcs__ typedef T_dis T_dcs; #endif #ifndef __T_hdlc_info__ #define __T_hdlc_info__ /* * HDLC information field * CCDGEN:WriteStruct_Count==3077 */ typedef struct { U8 crp; /*< 0: 1> CRP flag */ U8 c_pwd; /*< 1: 1> length of PWD */ U8 pwd[PWD_LEN]; /*< 2: 20> password */ U8 c_sub; /*< 22: 1> length of SUB */ U8 sub[SUB_LEN]; /*< 23: 20> subaddress */ U8 c_sep; /*< 43: 1> length of SEP */ U8 sep[SEP_LEN]; /*< 44: 20> selective polling */ U8 c_nsc; /*< 64: 1> length of NSC */ U8 nsc[NSC_LEN]; /*< 65: 90> non-standard facilities command */ U8 c_nsf; /*<155: 1> length of NSF */ U8 nsf[NSF_LEN]; /*<156: 90> non-standard facilities */ U8 c_tsi; /*<246: 1> length of TSI */ U8 tsi[TSI_LEN]; /*<247: 20> transmitting subscriber identification */ U8 c_cig; /*<267: 1> length of CIG */ U8 cig[CIG_LEN]; /*<268: 20> calling subscriber identification */ U8 c_csi; /*<288: 1> length of CSI */ U8 csi[CSI_LEN]; /*<289: 20> calling subscriber identification */ U8 c_nss; /*<309: 1> length of NSS */ U8 nss[NSS_LEN]; /*<310: 90> non-standard set-up */ U8 v_dis; /*<400: 1> DIS flag */ U8 _align0; /*<401: 1> alignment */ U8 _align1; /*<402: 1> alignment */ U8 _align2; /*<403: 1> alignment */ T_dis dis; /*<404: 48> digital identification signal */ U8 v_dcs; /*<452: 1> DCS flag */ U8 _align3; /*<453: 1> alignment */ U8 _align4; /*<454: 1> alignment */ U8 _align5; /*<455: 1> alignment */ T_dcs dcs; /*<456: 48> digital command signal */ U8 v_dtc; /*<504: 1> DTC flag */ U8 _align6; /*<505: 1> alignment */ U8 _align7; /*<506: 1> alignment */ U8 _align8; /*<507: 1> alignment */ T_dtc dtc; /*<508: 48> digital transmit command */ } T_hdlc_info; #endif /* * End of substructure section, begin of primitive definition section */ #ifndef __T_T30_ACTIVATE_REQ__ #define __T_T30_ACTIVATE_REQ__ /* * * CCDGEN:WriteStruct_Count==3080 */ typedef struct { U16 trans_rate; /*< 0: 2> transmission rate */ U8 half_rate; /*< 2: 1> half-rate flag */ U8 threshold; /*< 3: 1> tcf threshold */ U16 frames_per_prim; /*< 4: 2> no. of frames per primitive */ U8 bitorder; /*< 6: 1> Bitorder */ U8 _align0; /*< 7: 1> alignment */ } T_T30_ACTIVATE_REQ; #endif #ifndef __T_T30_CONFIG_REQ__ #define __T_T30_CONFIG_REQ__ /* * * CCDGEN:WriteStruct_Count==3081 */ typedef struct { U8 hdlc_report; /*< 0: 1> HDLC report mode */ U8 _align0; /*< 1: 1> alignment */ U16 test_mode; /*< 2: 2> Test mode */ } T_T30_CONFIG_REQ; #endif #ifndef __T_T30_CAP_IND__ #define __T_T30_CAP_IND__ /* * * CCDGEN:WriteStruct_Count==3082 */ typedef struct { T_hdlc_info hdlc_info; /*< 0:556> HDLC information field */ } T_T30_CAP_IND; #endif #ifndef __T_T30_CAP_REQ__ #define __T_T30_CAP_REQ__ /* * * CCDGEN:WriteStruct_Count==3083 */ typedef struct { T_hdlc_info hdlc_info; /*< 0:556> HDLC information field */ } T_T30_CAP_REQ; #endif #ifndef __T_T30_DTI_REQ__ #define __T_T30_DTI_REQ__ /* * * CCDGEN:WriteStruct_Count==3084 */ typedef struct { U8 dti_conn; /*< 0: 1> DTI connect */ U8 entity_name[T30_ENTITY_NAME_LEN]; /*< 1: 6> name of an neighbour entity */ U8 _align0; /*< 7: 1> alignment */ U32 link_id; /*< 8: 4> Link identifier */ U8 dti_direction; /*< 12: 1> DTI direction */ U8 _align1; /*< 13: 1> alignment */ U8 _align2; /*< 14: 1> alignment */ U8 _align3; /*< 15: 1> alignment */ } T_T30_DTI_REQ; #endif #ifndef __T_T30_DTI_CNF__ #define __T_T30_DTI_CNF__ /* * * CCDGEN:WriteStruct_Count==3085 */ typedef struct { U8 dti_conn; /*< 0: 1> DTI connect */ U8 _align0; /*< 1: 1> alignment */ U8 _align1; /*< 2: 1> alignment */ U8 _align2; /*< 3: 1> alignment */ } T_T30_DTI_CNF; #endif #ifndef __T_T30_DTI_IND__ #define __T_T30_DTI_IND__ /* * * CCDGEN:WriteStruct_Count==3086 */ typedef struct { U8 dummy; /*< 0: 1> no parameters */ } T_T30_DTI_IND; #endif #ifndef __T_T30_PHASE_IND__ #define __T_T30_PHASE_IND__ /* * * CCDGEN:WriteStruct_Count==3087 */ typedef struct { U8 phase; /*< 0: 1> T.30 phase */ U8 _align0; /*< 1: 1> alignment */ U8 _align1; /*< 2: 1> alignment */ U8 _align2; /*< 3: 1> alignment */ } T_T30_PHASE_IND; #endif #ifndef __T_T30_SGN_IND__ #define __T_T30_SGN_IND__ /* * * CCDGEN:WriteStruct_Count==3088 */ typedef struct { U8 sgn; /*< 0: 1> binary coded signal */ U8 _align0; /*< 1: 1> alignment */ U8 _align1; /*< 2: 1> alignment */ U8 _align2; /*< 3: 1> alignment */ } T_T30_SGN_IND; #endif #ifndef __T_T30_SGN_REQ__ #define __T_T30_SGN_REQ__ /* * * CCDGEN:WriteStruct_Count==3089 */ typedef struct { U8 sgn; /*< 0: 1> binary coded signal */ U8 _align0; /*< 1: 1> alignment */ U8 _align1; /*< 2: 1> alignment */ U8 _align2; /*< 3: 1> alignment */ } T_T30_SGN_REQ; #endif #ifndef __T_T30_CMPL_IND__ #define __T_T30_CMPL_IND__ /* * * CCDGEN:WriteStruct_Count==3090 */ typedef struct { U8 cmpl; /*< 0: 1> completion */ U8 _align0; /*< 1: 1> alignment */ U8 _align1; /*< 2: 1> alignment */ U8 _align2; /*< 3: 1> alignment */ } T_T30_CMPL_IND; #endif #ifndef __T_T30_REPORT_IND__ #define __T_T30_REPORT_IND__ /* * * CCDGEN:WriteStruct_Count==3091 */ typedef struct { U8 dir; /*< 0: 1> direction of call */ U8 _align0; /*< 1: 1> alignment */ U8 _align1; /*< 2: 1> alignment */ U8 _align2; /*< 3: 1> alignment */ T_sdu sdu; /*< 4: ? > Service Data Unit */ } T_T30_REPORT_IND; #endif #ifndef __T_T30_MODIFY_REQ__ #define __T_T30_MODIFY_REQ__ /* * * CCDGEN:WriteStruct_Count==3092 */ typedef struct { U16 trans_rate; /*< 0: 2> transmission rate */ U8 half_rate; /*< 2: 1> half-rate flag */ U8 _align0; /*< 3: 1> alignment */ } T_T30_MODIFY_REQ; #endif #ifndef __T_T30_ERROR_IND__ #define __T_T30_ERROR_IND__ /* * * CCDGEN:WriteStruct_Count==3093 */ typedef struct { U16 cause; /*< 0: 2> error cause */ U8 _align0; /*< 2: 1> alignment */ U8 _align1; /*< 3: 1> alignment */ } T_T30_ERROR_IND; #endif #ifndef __T_T30_EOL_IND__ #define __T_T30_EOL_IND__ /* * * CCDGEN:WriteStruct_Count==3094 */ typedef struct { U16 eol; /*< 0: 2> end of line count */ U8 _align0; /*< 2: 1> alignment */ U8 _align1; /*< 3: 1> alignment */ } T_T30_EOL_IND; #endif #ifndef __T_T30_DEACTIVATE_REQ__ #define __T_T30_DEACTIVATE_REQ__ /* * * CCDGEN:WriteStruct_Count==3095 */ typedef struct { U8 dummy; /*< 0: 1> no parameters */ } T_T30_DEACTIVATE_REQ; #endif #ifndef __T_T30_DEACTIVATE_CNF__ #define __T_T30_DEACTIVATE_CNF__ /* * * CCDGEN:WriteStruct_Count==3096 */ typedef struct { U8 dummy; /*< 0: 1> no parameters */ } T_T30_DEACTIVATE_CNF; #endif #ifndef __T_T30_ACTIVATE_CNF__ #define __T_T30_ACTIVATE_CNF__ /* * * CCDGEN:WriteStruct_Count==3097 */ typedef struct { U16 buf_size_rx; /*< 0: 2> buffer size RX */ U16 buf_size_tx; /*< 2: 2> buffer size TX */ } T_T30_ACTIVATE_CNF; #endif #ifndef __T_T30_PREAMBLE_IND__ #define __T_T30_PREAMBLE_IND__ /* * * CCDGEN:WriteStruct_Count==3098 */ typedef struct { U8 dummy; /*< 0: 1> no parameters */ } T_T30_PREAMBLE_IND; #endif #include "CDG_LEAVE.h" #endif