FreeCalypso > hg > fc-magnetite

view cdg-hybrid/cdginc/p_udpa.val @ 680:ee3ac8c617cb

Find changesets by keywords (author, files, the commit message), revision number or hash, or revset expression.
armio.c: set GPIO2 output high initially On TI-canonical platforms GPIO2 is DCD modem control output. In TI's original code the AI_InitIOConfig() function called from Init_Target() would configure GPIO2 as an output and set the initial output value to low, but then the init code in uartfax.c called from Init_Serial_Flows() would immediately change it to high, corresponding to DCD not asserted. The result is a momentary asserted-state glitch on the DCD output. The present change eliminates this glitch, setting DCD output to not-asserted initially like it should be.
author Mychaela Falconia <falcon@freecalypso.org>
date Thu, 25 Jun 2020 03:17:43 +0000
parents e7a67accfad9
children
line wrap: on
line source

/*
+--------------------------------------------------------------------------+
| PROJECT : PROTOCOL STACK                                                 |
| FILE    : p_udpa.val                                                     |
| SOURCE  : "sap\udpa.pdf"                                                 |
| LastModified : "2003-08-26"                                              |
| IdAndVersion : "8444.103.02.006"                                         |
| SrcFileTime  : "Thu Nov 29 09:56:38 2007"                                |
| Generated by CCDGEN_2.5.5A on Fri Oct 14 21:41:52 2016                   |
|           !!DO NOT MODIFY!!DO NOT MODIFY!!DO NOT MODIFY!!                |
+--------------------------------------------------------------------------+
*/

/* PRAGMAS
 * PREFIX                 : NONE
 * COMPATIBILITY_DEFINES  : NO (require PREFIX)
 * ALWAYS_ENUM_IN_VAL_FILE: NO
 * ENABLE_GROUP: NO
 * CAPITALIZE_TYPENAME: NO
 */


#ifndef P_UDPA_VAL
#define P_UDPA_VAL


#define CDG_ENTER__P_UDPA_VAL

#define CDG_ENTER__FILENAME _P_UDPA_VAL
#define CDG_ENTER__P_UDPA_VAL__FILE_TYPE CDGINC
#define CDG_ENTER__P_UDPA_VAL__LAST_MODIFIED _2003_08_26
#define CDG_ENTER__P_UDPA_VAL__ID_AND_VERSION _8444_103_02_006

#define CDG_ENTER__P_UDPA_VAL__SRC_FILE_TIME _Thu_Nov_29_09_56_38_2007

#include "CDG_ENTER.h"

#undef CDG_ENTER__P_UDPA_VAL

#undef CDG_ENTER__FILENAME


/*
 * Value constants for VAL_dti_conn
 */
#define UDPA_CONNECT_DTI               (0x0)      /* Connect DTI2 to UDP            */
#define UDPA_DISCONNECT_DTI            (0x1)      /* Disconnect DTI2 from UDP       */

/*
 * Value constants for VAL_link_id
 */
#define UDPA_LINK_ID_DEFAULT           (0x0)      /* Default link id                */

/*
 * Value constants for VAL_dti_direction
 */
#define UDPA_DTI_TO_HIGHER_LAYER       (0x0)      /* DTI2 used normally             */
#define UDPA_DTI_TO_LOWER_LAYER        (0x1)      /* DTI2 is inverted               */

/*
 * Value constants for VAL_cmd
 */
#define UDPA_CONFIG_UP                 (0x0)      /* enable the interface           */
#define UDPA_CONFIG_DOWN               (0x1)      /* disable the interface          */

/*
 * user defined constants
 */
#define UDPA_ENTITY_NAME_LEN           (0x6)      

#include "CDG_LEAVE.h"


#endif