FreeCalypso > hg > fc-magnetite

view cdg3/sap/ph.pdf @ 680:ee3ac8c617cb

Find changesets by keywords (author, files, the commit message), revision number or hash, or revset expression.
armio.c: set GPIO2 output high initially On TI-canonical platforms GPIO2 is DCD modem control output. In TI's original code the AI_InitIOConfig() function called from Init_Target() would configure GPIO2 as an output and set the initial output value to low, but then the init code in uartfax.c called from Init_Serial_Flows() would immediately change it to high, corresponding to DCD not asserted. The result is a momentary asserted-state glitch on the DCD output. The present change eliminates this glitch, setting DCD output to not-asserted initially like it should be.
author Mychaela Falconia <falcon@freecalypso.org>
date Thu, 25 Jun 2020 03:17:43 +0000
parents c15047b3d00d
children
line wrap: on
line source

;********************************************************************************
;*** File           : ph.pdf
;*** Creation       : Wed Mar 11 09:58:34 CST 2009
;*** XSLT Processor : Apache Software Foundation / http://xml.apache.org/xalan-j / supports XSLT-Ver: 1
;*** Copyright      : (c) Texas Instruments AG, Berlin Germany 2002
;********************************************************************************
;*** Document Type  : Service Access Point Specification
;*** Document Name  : ph
;*** Document No.   : 6147.112.01.100
;*** Document Date  : 2001-10-26
;*** Document Status: APPROVED
;*** Document Author: SBK
;********************************************************************************



PRAGMA 	SRC_FILE_TIME 	"Thu Nov 29 09:50:28 2007"
PRAGMA 	LAST_MODIFIED 	"2001-10-26"
PRAGMA 	ID_AND_VERSION 	"6147.112.01.100"



CONST 	DUMMY_PH 	0 	; Dummy, not used, needed to satisfy tool chain which requires at least one constant definition in a SAP



VALTAB 	VAL_ch_type
VAL 	0 	CH_TYPE_SACCH 	"SACCH"
VAL 	1 	CH_TYPE_SDCCH 	"SDCCH"
VAL 	2 	CH_TYPE_FACCH 	"FACCH Full Rate"
VAL 	3 	 	"reserved"
VAL 	4 	 	"reserved"
VAL 	5 	 	"reserved"
VAL 	6 	 	"reserved"
VAL 	7 	CH_TYPE_FACCH_HR 	"FACCH Half Rate"




VAR 	l2_channel 	"Layer 2 channel-type" 	B

VAL 	@p_mphc - VAL_l2_channel@ 	

VAR 	l_buf 	"length of content in bit" 	S


VAR 	o_buf 	"offset of content in bit" 	S


VAR 	buf 	"buffer content; the actual size of buf is determined and allocated at run-time and not restricted to 1;" 	B


VAR 	dummy 	"dummy not used" 	B





COMP 	sdu 	 "message unit"
{
 	l_buf 	 ; length of content in bit
 	o_buf 	 ; offset of content in bit
 	buf 	[1] 	 ; buffer content; the actual size of buf is determined and allocated at run-time and not restricted to 1;
}






; PH_READY_TO_SEND 	0x4100
; PH_DATA_REQ 	0x0100
; PH_TRACE_IND 	0x4102



PRIM 	PH_READY_TO_SEND 	0x4100
{
 	l2_channel AS ch_type 	 ; channel type
}






PRIM 	PH_DATA_REQ 	0x0100
{
 	l2_channel AS ch_type 	 ; channel type
 	dummy 	 ; dummy not used; reserved
 	sdu 	 ; message unit
}






PRIM 	PH_TRACE_IND 	0x4102
{
 	dummy 	 ; dummy not used; not used
}