| Tue, 13 Feb 2018 07:02:17 +0000 |
Mychaela Falconia |
autocal: vout_t definition factored out of txband.h into txvout.h
|
| Tue, 13 Feb 2018 06:22:32 +0000 |
Mychaela Falconia |
fc-rfcal-txband: channel calibration implemented
|
| Tue, 13 Feb 2018 05:17:13 +0000 |
Mychaela Falconia |
fc-rfcal-txband: set calchan indices in the levels table
|
| Tue, 13 Feb 2018 05:06:28 +0000 |
Mychaela Falconia |
fc-rfcal-txband: data struct preparation for channel calibration
|
| Tue, 13 Feb 2018 04:39:33 +0000 |
Mychaela Falconia |
doc/Test-system-interface: txpwr-cal-channel addition documented
|
| Tue, 13 Feb 2018 04:29:38 +0000 |
Mychaela Falconia |
fc-cmu200d: implemented channel switching in Tx power calibration
|
| Tue, 13 Feb 2018 03:18:38 +0000 |
Mychaela Falconia |
doc/Tx-cal-theory: update with properly calibrated CMU200 and cabling setup
|
| Tue, 13 Feb 2018 02:25:27 +0000 |
Mychaela Falconia |
txlevels: updated README
|
| Tue, 13 Feb 2018 01:11:41 +0000 |
Mychaela Falconia |
txlevels: rf3166-ideal and rf3166-fcdev3b profiles
|
| Tue, 13 Feb 2018 00:31:40 +0000 |
Mychaela Falconia |
txlevels/fcom1-900: no need for 750 basis pt, it's past the useful range
|
| Tue, 13 Feb 2018 00:30:35 +0000 |
Mychaela Falconia |
txlevels/fcom1-1900: we are now able to get the full 30 dBm
|
| Sat, 09 Dec 2017 16:06:07 +0000 |
Mychaela Falconia |
fc-rfcal-txband: added delay which should prevent intermittent fw crash
|
| Sat, 09 Dec 2017 07:07:19 +0000 |
Mychaela Falconia |
INSTALL: we need fc-host-tools-r6 or later for ERROR_RFFAIL
|
| Sat, 09 Dec 2017 07:01:13 +0000 |
Mychaela Falconia |
autocal: use the new ERROR_RFFAIL exit code
|
| Sun, 13 Aug 2017 05:04:48 +0000 |
Mychaela Falconia |
doc/Tx-cal-theory: update regarding our current FCDEV3B calibration
|
| Sat, 12 Aug 2017 08:47:09 +0000 |
Mychaela Falconia |
fc-rfcal-txband: fixed bug in the corner case when
|
| Fri, 11 Aug 2017 03:20:43 +0000 |
Mychaela Falconia |
fc-rfcal-txband: added safety checks for NaN power measurements and
|
| Fri, 11 Aug 2017 02:45:10 +0000 |
Mychaela Falconia |
fc-rfcal-vcxo: added check for final freq offset being within 70 Hz
|
| Fri, 11 Aug 2017 02:21:32 +0000 |
Mychaela Falconia |
fc-rfcal-vcxo: abort on getting a NaN response
|
| Mon, 17 Jul 2017 22:49:35 +0000 |
Mychaela Falconia |
doc/Tx-cal-theory: update with both theory and practice
|
| Mon, 17 Jul 2017 19:15:44 +0000 |
Mychaela Falconia |
INSTALL: refer to doc/Cable-config-howto
|
| Mon, 17 Jul 2017 19:07:50 +0000 |
Mychaela Falconia |
top README: refer to doc/General-flow
|
| Mon, 17 Jul 2017 18:26:30 +0000 |
Mychaela Falconia |
doc: Cable-config-howto and General-flow written
|
| Mon, 17 Jul 2017 08:28:57 +0000 |
Mychaela Falconia |
top README and INSTALL files added
|
| Mon, 17 Jul 2017 07:03:11 +0000 |
Mychaela Falconia |
doc/Test-system-interface: typo fix
|
| Mon, 17 Jul 2017 06:31:19 +0000 |
Mychaela Falconia |
doc/cableconf-example with proper commentary
|
| Mon, 17 Jul 2017 06:12:53 +0000 |
Mychaela Falconia |
top Makefile: scripts added to SUBDIR
|
| Mon, 17 Jul 2017 05:51:31 +0000 |
Mychaela Falconia |
fc-rfcal-tri900 script and fc-rfcal-tee helper implemented
|
| Mon, 17 Jul 2017 01:38:00 +0000 |
Mychaela Falconia |
Makefile magic: install txlevels profiles
|
| Mon, 17 Jul 2017 01:17:38 +0000 |
Mychaela Falconia |
omrf1 txlevels profiles renamed to fcom1, see added fcom1.README
|
| Mon, 17 Jul 2017 00:03:27 +0000 |
Mychaela Falconia |
checking in cableconf and txlevels config files
|
| Sun, 16 Jul 2017 23:42:29 +0000 |
Mychaela Falconia |
fc-cmu200d: ignore SIGPIPE so we don't exit if a client terminates
|
| Sun, 16 Jul 2017 00:00:46 +0000 |
Mychaela Falconia |
fc-rfcal-txband: FFS write implemented
|
| Sat, 15 Jul 2017 23:57:56 +0000 |
Mychaela Falconia |
fc-rfcal-txband: works after a couple of bugfixes
|
| Sat, 15 Jul 2017 23:09:46 +0000 |
Mychaela Falconia |
fc-rfcal-txband: initial implementation complete, ready to test
|
| Sat, 15 Jul 2017 22:48:29 +0000 |
Mychaela Falconia |
fc-rfcal-txband: implemented computation of APC from basis
|
| Sat, 15 Jul 2017 21:34:29 +0000 |
Mychaela Falconia |
fc-rfcal-txband: implemented the slope computations after basis run
|
| Sat, 15 Jul 2017 21:22:38 +0000 |
Mychaela Falconia |
fc-rfcal-txband: basis run implemented
|
| Sat, 15 Jul 2017 21:06:43 +0000 |
Mychaela Falconia |
fc-rfcal-txband: dBm to Vout function implemented
|
| Sat, 15 Jul 2017 20:47:31 +0000 |
Mychaela Falconia |
fc-rfcal-txband: implemented check for increasing basis points
|
| Sat, 15 Jul 2017 20:25:31 +0000 |
Mychaela Falconia |
fc-rfcal-txband: implemented initial calchan clearing
|
| Sat, 15 Jul 2017 20:08:55 +0000 |
Mychaela Falconia |
fc-rfcal-txband: reading of basis & targets setting files implemented
|
| Sat, 15 Jul 2017 19:22:30 +0000 |
Mychaela Falconia |
fc-rfcal-txband started
|
| Sat, 15 Jul 2017 18:20:48 +0000 |
Mychaela Falconia |
autocal: rxband.c renamed to rxbandmain.c for consistency
|
| Sat, 15 Jul 2017 18:14:49 +0000 |
Mychaela Falconia |
autocal: C main modules for standalone programs renamed more sensibly
|
| Sat, 15 Jul 2017 17:58:14 +0000 |
Mychaela Falconia |
autocal: started defining structures for fc-rfcal-txband
|
| Fri, 14 Jul 2017 06:58:36 +0000 |
Mychaela Falconia |
fc-rfcal-txcheck: spec and error values added to the output
|
| Fri, 14 Jul 2017 05:03:10 +0000 |
Mychaela Falconia |
fc-cmu200d: CMU200 external att setting implemented in RF analyzer mode
|
| Fri, 14 Jul 2017 04:52:03 +0000 |
Mychaela Falconia |
fc-cmu200d: CMU200 external attenuation setting implemented in signal gen mode
|
| Fri, 14 Jul 2017 04:34:15 +0000 |
Mychaela Falconia |
fc-cmu200d: implemented reading and parsing of cable config files (-c arg)
|
| Sun, 28 May 2017 07:22:09 +0000 |
Mychaela Falconia |
fc-rfcal-rxband: FFS write implemented
|
| Sun, 28 May 2017 06:42:29 +0000 |
Mychaela Falconia |
doc/Tx-cal-theory written
|
| Sun, 28 May 2017 05:10:32 +0000 |
Mychaela Falconia |
doc/Rx-cal-theory: typo fix
|
| Sun, 28 May 2017 05:02:24 +0000 |
Mychaela Falconia |
doc/VCXO-vs-VCTCXO written
|
| Sun, 28 May 2017 03:21:34 +0000 |
Mychaela Falconia |
doc/Rx-cal-theory written
|
| Sun, 28 May 2017 00:33:10 +0000 |
Mychaela Falconia |
fc-rfcal-rxband: channel calibration implemented
|
| Sun, 28 May 2017 00:10:16 +0000 |
Mychaela Falconia |
fc-rfcal-rxband: almost finished
|
| Sat, 27 May 2017 23:35:06 +0000 |
Mychaela Falconia |
fc-rfcal-rxband: upload of GMagic to DUT implemented
|
| Sat, 27 May 2017 23:23:35 +0000 |
Mychaela Falconia |
autocal/l1tmops.c: do_rftr() added
|
| Sat, 27 May 2017 23:17:14 +0000 |
Mychaela Falconia |
autocal/rxband.c: do_gmagic() factored out of main()
|
| Sat, 27 May 2017 23:05:28 +0000 |
Mychaela Falconia |
fc-rfcal-rxband started
|
| Sat, 27 May 2017 20:02:10 +0000 |
Mychaela Falconia |
fc-rfcal-txbasis written, ready to test
|
| Sat, 27 May 2017 19:44:08 +0000 |
Mychaela Falconia |
autocal Tx: txpwr-cal-setup factored out of fc-rfcal-txcheck
|
| Sat, 27 May 2017 16:03:40 +0000 |
Mychaela Falconia |
fc-rfcal-txcheck ready to test
|
| Sat, 27 May 2017 15:41:54 +0000 |
Mychaela Falconia |
rf-cal-txcheck started
|
| Sat, 27 May 2017 07:53:36 +0000 |
Mychaela Falconia |
autocal: use DUALEXT STD for 900 and 1800 MHz bands
|
| Sat, 27 May 2017 07:49:23 +0000 |
Mychaela Falconia |
autocal/gmagicmain.c: printf fix
|
| Sat, 27 May 2017 07:33:39 +0000 |
Mychaela Falconia |
fc-rfcal-gmagic ready to test
|
| Sat, 27 May 2017 07:23:20 +0000 |
Mychaela Falconia |
autocal: Rx cal main engine implemented
|
| Sat, 27 May 2017 07:03:08 +0000 |
Mychaela Falconia |
autocal/l1meas.c: implemented reading of auto-stats
|
| Sat, 27 May 2017 06:46:17 +0000 |
Mychaela Falconia |
autocal: preparations for receiving auto stats and rfe completion
|
| Sat, 27 May 2017 06:25:59 +0000 |
Mychaela Falconia |
Rx cal: started the single measurement code
|
| Sat, 27 May 2017 05:48:04 +0000 |
Mychaela Falconia |
autocal: scw implemented for Rx cal
|
| Sat, 27 May 2017 05:33:42 +0000 |
Mychaela Falconia |
autocal: started Rx cal core code
|
| Sat, 27 May 2017 05:11:43 +0000 |
Mychaela Falconia |
fc-rfcal-gmagic: main() coming along
|
| Sat, 27 May 2017 05:04:14 +0000 |
Mychaela Falconia |
fc-rfcal-gmagic started
|
| Sat, 27 May 2017 02:43:43 +0000 |
Mychaela Falconia |
fc-cmu200d: power-meas implemented
|
| Sat, 27 May 2017 02:38:28 +0000 |
Mychaela Falconia |
fc-cmu200d: VCXO calibration mode generalized into RF analyzer mode
|
| Sat, 27 May 2017 02:17:00 +0000 |
Mychaela Falconia |
fc-cmu200d: implemented RF1/RF2 port selection
|
| Sat, 27 May 2017 02:10:29 +0000 |
Mychaela Falconia |
fc-cmu200d: use either main or Aux Tx
|
| Sat, 27 May 2017 01:58:06 +0000 |
Mychaela Falconia |
fc-cmu200d: added command line options
|
| Fri, 26 May 2017 16:00:06 +0000 |
Mychaela Falconia |
doc/Test-system-interface: added commands for Tx power level calibration
|
| Tue, 23 May 2017 01:05:22 +0000 |
Mychaela Falconia |
doc/VCXO-notes renamed to VCXO-manual-cal
|
| Tue, 23 May 2017 00:33:10 +0000 |
Mychaela Falconia |
fc-cmu200d: check for errors on serial port write
|
| Tue, 23 May 2017 00:12:10 +0000 |
Mychaela Falconia |
top Makefile: autocal added to SUBDIR
|
| Tue, 23 May 2017 00:11:16 +0000 |
Mychaela Falconia |
autocal/Makefile: make install added
|
| Tue, 23 May 2017 00:08:41 +0000 |
Mychaela Falconia |
fc-rfcal-vcxo: added setlinebuf(stdout) to allow easier logging with tee
|
| Tue, 23 May 2017 00:05:33 +0000 |
Mychaela Falconia |
fc-rfcal-vcxo: upload and FFS save implemented
|
| Mon, 22 May 2017 23:50:32 +0000 |
Mychaela Falconia |
autocal/l1tmops.c: rftw and me implemented
|
| Mon, 22 May 2017 23:36:14 +0000 |
Mychaela Falconia |
fc-rfcal-vcxo: afcparams computation implemented
|
| Mon, 22 May 2017 23:10:34 +0000 |
Mychaela Falconia |
fc-rfcal-vcxo: almost done
|
| Mon, 22 May 2017 22:27:22 +0000 |
Mychaela Falconia |
fc-rfcal-vcxo: search for zero crossing implemented
|
| Mon, 22 May 2017 22:09:59 +0000 |
Mychaela Falconia |
autocal/vcxomeas.c: brown paper bag
|
| Mon, 22 May 2017 22:00:36 +0000 |
Mychaela Falconia |
fc-rfcal-vcxo ready for first test
|
| Mon, 22 May 2017 21:19:33 +0000 |
Mychaela Falconia |
autocal/vcxomain.c: coming along
|
| Mon, 22 May 2017 21:01:29 +0000 |
Mychaela Falconia |
autocal: started linking fc-rfcal-vcxo
|
| Mon, 22 May 2017 20:51:55 +0000 |
Mychaela Falconia |
autocal: beginning of fc-rfcal-vcxo
|
| Mon, 22 May 2017 20:35:42 +0000 |
Mychaela Falconia |
autocal: set_std_band() function replaced with RFPW_STD_BAND() macro
|
| Mon, 22 May 2017 20:20:49 +0000 |
Mychaela Falconia |
autocal/tsidsock.c: implemented command/response protocol
|
| Mon, 22 May 2017 18:36:26 +0000 |
Mychaela Falconia |
autocal/l1tmops.c: rxpw and txpw implemented
|
| Mon, 22 May 2017 18:30:24 +0000 |
Mychaela Falconia |
autocal/l1tmops.c: started implementing basic operations
|
| Mon, 22 May 2017 17:45:30 +0000 |
Mychaela Falconia |
autocal/l1tmops.c started
|
| Sun, 21 May 2017 23:04:42 +0000 |
Mychaela Falconia |
autocal/rvinterf.c now has all essential code for talking to rvinterf
|
| Sun, 21 May 2017 23:00:32 +0000 |
Mychaela Falconia |
autocal/tsidsock.c written
|
| Sun, 21 May 2017 22:58:04 +0000 |
Mychaela Falconia |
starting autocal
|
| Sun, 21 May 2017 19:23:03 +0000 |
Mychaela Falconia |
cmu200/logs/freq-meas-working: log saved
|
| Sun, 21 May 2017 19:22:11 +0000 |
Mychaela Falconia |
fc-cmu200d: freq-meas works
|
| Sun, 21 May 2017 18:57:44 +0000 |
Mychaela Falconia |
cmu200/logs/read-mod-response: log saved
|
| Sun, 21 May 2017 18:39:49 +0000 |
Mychaela Falconia |
fc-cmu200d: do setlinebuf(stdout) for easier logging with tee
|
| Sun, 21 May 2017 18:20:55 +0000 |
Mychaela Falconia |
fc-cmu200d: freq-meas implemented without response parsing
|
| Sun, 21 May 2017 08:03:35 +0000 |
Mychaela Falconia |
fc-cmu200d: vcxo-cal-setup implemented
|
| Sun, 21 May 2017 07:52:11 +0000 |
Mychaela Falconia |
fc-cmu200d: signal-gen-off implemented
|
| Sun, 21 May 2017 07:48:54 +0000 |
Mychaela Falconia |
fc-cmu200d: signal-gen-sine implemented
|
| Sun, 21 May 2017 07:21:17 +0000 |
Mychaela Falconia |
fc-cmu200d: signal-gen-setup implemented
|
| Sun, 21 May 2017 07:01:53 +0000 |
Mychaela Falconia |
fc-cmu200d: started implementing operation modes
|
| Sun, 21 May 2017 06:37:56 +0000 |
Mychaela Falconia |
fc-cmu200d: band and ARFCN tables implemented
|
| Sat, 20 May 2017 18:58:44 +0000 |
Mychaela Falconia |
.hgignore added
|
| Sat, 20 May 2017 18:49:35 +0000 |
Mychaela Falconia |
initial import of rfcal code and docs from freecalypso-tools repository
|
