view src/cs/layer1/tpu_drivers/source0/tpudrv8.h @ 86:425ab6d987f3
src/libsys: pieced together from Citrine
author |
Mychaela Falconia <falcon@freecalypso.org> |
date |
Fri, 20 Jul 2018 20:36:19 +0000 (2018-07-20) |
parents |
b6a5e36de839 |
children |
|
line source
/****************** Revision Controle System Header ***********************
* GSM Layer 1 software
* Copyright (c) Texas Instruments 1998
*
* Filename tpudrv8.h
* Copyright 2003 (C) Texas Instruments
*
****************** Revision Controle System Header ***********************/
//SI4133 definitions
#define WordAdd0000 0x000000 //Main Configuration
#define AutoPDB 0x000080 //Auto Power Down - Uses PWDNB pin
#define AuxSel 0x030000 //Auxiliary output pin use = LOCK Detect
#define WordAdd0011 0x000003 //RF1 N Divider
#define WordAdd0100 0x000004 //RF2 N Divider
#define WordAdd0101 0x000005 //IF N Divider
#define RFPWR 0x000020 //RF LO high power
#define XPDM 0x000100 //Reference amplifier ON when PWDNB pin = 0
//TRF6053 definitions
#define Mode0 0x000000
#define Mode1 0x000001
#define Mode2 0x000003
#define Mode3 0x000005
#define Mode4 0x000007
#define LNAMixPwrOn 0x000080 //Mode0
#define VCODiv2PwrOn 0x000040 //Mode0
#define RXBBIFStgPwrOn 0x000020 //Mode0
#define OFFStrCalOn 0x000010 //Mode0
#define VCORDivPwrOn 0x000008 //Mode0
#define MixLOBuffPwrOn 0x000004 //Mode0
#define TXStagesPwrOn 0x000002 //Mode0
#define FreqDetDis 0x000400 //Mode4
#define IFVCOExternal 0x000200 //Mode4
#define IFPLLBuffDis 0x000100 //Mode4
#define LBandLNAExt 0x000080 //Mode4
#define HBandLNAExt 0x000040 //Mode4
#define Div2ToRXStgs 0x000020 //Mode4
#define DivRToTXStgs 0x000010 //Mode4
#define ChgPPLBNeg 0x000010 //Mode2
#define ChgPPHBNeg 0x000010 //Mode3
#define PreCCLBDis 0x000008 //Mode2
#define PreCCHBDis 0x000008 //Mode3
#define LNAGainLow 0x000010 //Mode2
#define BandHigh 0x000008 //Mode1
#define LowBIF610 0x000020 //Mode2
#define HighBIF412 0x000020 //Mode3
#define HighBIF25 0x000040 //Mode3
#define HighBIF410 0x000060 //Mode3
/*------------------------------------------*/
/* Download delay values */
/*------------------------------------------*/
#define TRF6053_DOWNLOAD_TIME 15
#define SYNTH_DOWNLOAD_TIME 20
//--------------------------------------------
// internal tpu timing
//--------------------------------------------
#define DLT_1 1 // 1 tpu instruction = 1 qbit
#define DLT_2 2
#define DLT_3 3
#define DLT_4 4
#define DLT_1B 4 // 3*move + 1*byte (download)
#define DLT_2B 6 // 4*move + 2*byte
#define DLT_3B 8 // 5*move + 3*byte
#define SL_SU_DELAY1 4 // No. bits to send + load data to shift + send write cmd + 1
#define SL_SU_DELAY2 3 // load data to shift + send write cmd + 1
#define SL_SU_DELAY3 5 // SL_SU_DELAY1 + serialization
/*------------------------------------------*/
/* Download delay values */
/*------------------------------------------*/
// 0.9230769 usec ~ 1 qbit i.e. 200 usec is ~ 217 qbit
#define T TPU_CLOCK_RANGE // TODO: should be a define from L1.
// time below are offset to when BDLENA goes low
#define TRF_R11 ( 0 - DLT_1B) // disable BDLON & BDLENA
#define TRF_R10 ( - 5 - DLT_1B) // disable TRF6053
// burst data comes here
// time below are offset to when BDLENA goes high
#define TRF_R9 (PROVISION_TIME - 0 - DLT_1B) // enable BDLENA, disable BDLCAL
#define TRF_R8 (PROVISION_TIME - 11 - DLT_1B) // power on RX front end, DC cal. off
#define TRF_R7 (PROVISION_TIME - 65 - DLT_1B) // enable BDLCAL
#define TRF_R6 (PROVISION_TIME - 72 - DLT_1B) // enable BDLON
#define TRF_R5 (PROVISION_TIME - 76 - DLT_1B) // power on receiver, start DC cal.
#define TRF_R4 (PROVISION_TIME - 80 - DLT_2B) // set RX gain & band.
// ADC read, uses min 11 qbit due to 5 wait
#define TRF_R3 (PROVISION_TIME - 196 - DLT_1B) // power up TRF2253
#define TRF_R1 (PROVISION_TIME - 205 - DLT_3B) // set RF PLL N counter = r1 and IF PLL N counter in TRF2253 = r2
// time below are offset to when BULENA goes low
#define TRF_T13 ( 32 - DLT_1B) // disable PA_ON, BULON, TRF6053
#define TRF_T12 ( 18 - DLT_1 ) // disable TSPACT01
#define TRF_T11 ( 0 - DLT_1B) // disable BULENA
#define TRF_T10_1 (- 40 - DLT_1B) // ADC read
// burst data comes here
// time below are offset to when BULENA goes high
#define TRF_T10 (+ 15 - DLT_3) // enable PA_ON + 2*rfswitch
#define TRF_T9 (- 0 - DLT_1B) // enable BULENA
#define TRF_T8 (- 109 - DLT_2B) // power on transceiver
#define TRF_T7 (- 115 - DLT_1B) // disable BULCAL
#define TRF_T6 (- 230 - DLT_1B) // power up TRF2253
#define TRF_T5 (- 233 - DLT_2B) // set TX band in TRF6053
#define TRF_T3 (- 249 - DLT_3B) // set RF PLL N counter = t3 and IF PLL N counter in TRF2253 = t4
#define TRF_T2 (- 260 - DLT_1B) // enable BULCAL
#define TRF_T1 (- 278 - DLT_1B) // enable BULON
#if (BOARD == 7) || (BOARD == 8) || (BOARD == 9) || (BOARD == 40) || (BOARD == 41) || (BOARD == 42) || (BOARD == 43) || (BOARD == 45)
#define PA_ON 0x20 // act5
#define TSPACT01 0x02 // act1
// RF signals connected to TSPACTX
#define RX900 0x04 // act10
#define RX1800 0x08 // act11
#define TC1_DEVICE_ABB TC1_DEVICE0
#define TC1_DEVICE_RF TC1_DEVICE1
#define TC1_DEVICE_PLL TC1_DEVICE2
#endif
#if (BOARD == 6)
#define PA_ON 0x10 // act4
// RF signals connected to TSPACTX
#define RX900 0x08 // act11 => needs to be connected to act12
#define RX1800 0x04 // act10
#define TC1_DEVICE_ABB TC1_DEVICE0
#define TC1_DEVICE_PLL TC1_DEVICE1
#define TC1_DEVICE_RF TC1_DEVICE2
#endif
#ifdef TPUDRV8_C
// Function prototypes
SYS_UWORD16 Convert_l1_radio_freq(SYS_UWORD16 radio_freq);
#endif