FreeCalypso > hg > fc-selenite
view src/cs/layer1/tpu_drivers/source0/tpudrv35.h @ 157:fd5202e290bc
targets: j100 added
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Sun, 17 Mar 2019 07:13:14 +0000 |
parents | b6a5e36de839 |
children |
line wrap: on
line source
/****************** Revision Controle System Header *********************** * GSM Layer 1 software * Copyright (c) Texas Instruments 2001 * * Filename tpudrv35.h * Copyright 2003 (C) Texas Instruments * ****************** Revision Controle System Header ***********************/ //TRF2253 definitions #define WordAdd0000 0x000000 //Main Configuration #define AutoPDB 0x000080 //Auto Power Down - Uses PWDNB pin #define AuxSel 0x030000 //Auxiliary output pin use = LOCK Detect #define WordAdd0011 0x000003 //RF1 N Divider #define WordAdd0100 0x000004 //RF2 N Divider #define WordAdd0101 0x000005 //IF N Divider #define RFPWR 0x000020 //RF LO high power #define XPDM 0x000100 //Reference amplifier ON when PWDNB pin = 0 //TRF6053 definitions #define Mode0 0x000000 #define Mode1 0x000001 #define Mode2 0x000003 #define Mode3 0x000005 #define Mode4 0x000007 #define LNAMixPwrOn 0x000080 //Mode0 #define VCODiv2PwrOn 0x000040 //Mode0 #define RXBBIFStgPwrOn 0x000020 //Mode0 #define OFFStrCalOn 0x000010 //Mode0 #define VCORDivPwrOn 0x000008 //Mode0 #define MixLOBuffPwrOn 0x000004 //Mode0 #define TXStagesPwrOn 0x000002 //Mode0 #define BandHigh 0x000008 //Mode1 #define LNAGainLow 0x000010 //Mode2 #define ChgPPLBNeg 0x000010 //Mode2 #define LowBIF610 0x000020 //Mode2 #define PreCCLBDis 0x000008 //Mode2 #define ChgPPHBNeg 0x000010 //Mode3 #define PreCCHBDis 0x000008 //Mode3 #define HighBIF412 0x000020 //Mode3 #define HighBIF25 0x000040 //Mode3 #define HighBIF410 0x000060 //Mode3 #define FreqDetDis 0x000400 //Mode4 #define IFVCOExternal 0x000200 //Mode4 #define IFPLLBuffDis 0x000100 //Mode4 #define LBandLNAExt 0x000080 //Mode4 #define HBandLNAExt 0x000040 //Mode4 #define Div2ToRXStgs 0x000020 //Mode4 #define DivRToTXStgs 0x000010 //Mode4 /*------------------------------------------*/ /* Download delay values */ /*------------------------------------------*/ #define TRF6053_DOWNLOAD_TIME 15 #define SYNTH_DOWNLOAD_TIME 20 //-------------------------------------------- // internal tpu timing //-------------------------------------------- #define DLT_1 1 // 1 tpu instruction = 1 qbit #define DLT_2 2 #define DLT_3 3 #define DLT_4 4 #define DLT_1B 4 // 3*move + 1*byte (download) #define DLT_2B 6 // 4*move + 2*byte #define DLT_3B 8 // 5*move + 3*byte #define SL_SU_DELAY1 4 // No. bits to send + load data to shift + send write cmd + 1 #define SL_SU_DELAY2 3 // load data to shift + send write cmd + 1 #define SL_SU_DELAY3 5 // SL_SU_DELAY1 + serialization /*------------------------------------------*/ /* Download delay values */ /*------------------------------------------*/ // 0.9230769 usec ~ 1 qbit i.e. 200 usec is ~ 217 qbit #define T TPU_CLOCK_RANGE // TODO: should be a define from L1. // time below are offset to when BDLENA goes low #define TRF_R13 ( 5 - DLT_1B ) // disable rx path, fe, lna_gain #define TRF_R11 ( 0 - DLT_1B) // disable BDLON & BDLENA #define TRF_R10 ( - 5 - DLT_1B) // disable TRF6053 // burst data comes here // time below are offset to when BDLENA goes high #define TRF_R9 (PROVISION_TIME - 0 - DLT_1B) // enable BDLENA, disable BDLCAL #define TRF_R8 (PROVISION_TIME - 11 - DLT_1B) // set rx path + power on RX front end, DC cal. off #define TRF_R7 (PROVISION_TIME - 65 - DLT_1B) // enable BDLCAL #define TRF_R6 (PROVISION_TIME - 72 - DLT_1B) // enable BDLON #define TRF_R5 (PROVISION_TIME - 76 - DLT_1B) // power on receiver, start DC cal. #define TRF_R4 (PROVISION_TIME - 80 - DLT_2B) // set RX gain & band. // ADC read, uses min 11 qbit due to 5 wait #define TRF_R3 (PROVISION_TIME - 196 - DLT_1B) // power up TRF2253 #define TRF_R1 (PROVISION_TIME - 205 - DLT_3B) // set RF PLL N counter = r1 and IF PLL N counter in TRF2253 = r2 // time below are offset to when BULENA goes low #define TRF_T14 ( 34 - DLT_2) // disable PA_ON, , BULON, fe, rx path & lna #define TRF_T13 ( 29 - DLT_1B) // disable TRF6053 #define TRF_T12_1 ( 21 - DLT_1B) // disable fe_sw //#define TRF_T12 ( 18 - DLT_1 ) // disable TSPACT01 #define TRF_T11 ( 0 - DLT_1B) // disable BULENA #define TRF_T10_1 (- 40 - DLT_1B) // ADC read // burst data comes here // time below are offset to when BULENA goes high #define TRF_T10_0 (+ 27 - DLT_1B) //enable PA_ON #define TRF_T10 (+ 18 - DLT_1B) // set fe #define TRF_T9 (- 0 - DLT_1B) // enable BULENA #define TRF_T8_1 (- 100 - DLT_1B) // set TX_PCS_EN as required #define TRF_T8 (- 108 - DLT_2B) // power on transceiver #define TRF_T7 (- 115 - DLT_1B) // disable BULCAL #define TRF_T6 (- 230 - DLT_1B) // power up TRF2253 #define TRF_T5 (- 233 - DLT_2B) // set TX band in TRF6053 #define TRF_T3 (- 249 - DLT_3B) // set RF PLL N counter = t3 and IF PLL N counter in TRF2253 = t4 #define TRF_T2 (- 260 - DLT_1B) // enable BULCAL #define TRF_T1 (- 278 - DLT_1B) // enable BULON #if ((BOARD == 34)||(BOARD == 35)) #define PA_ON 0x01 // act0 #define DCS_RX_EN 0x02 // act1 #define PCS_RX_EN 0x04 // act2 #define PCS_TX_EN 0x08 // act3 #define LNA_GAIN 0x10 // act4 #define TX_SW_1 0x20 // act5 #define TX_SW_2 0x40 // act6 #define TX_SW_3 0x80 // act7 #define TX_SW_OFF (TX_SW_1 | TX_SW_2 | TX_SW_3) #define ACT_OFF TX_SW_OFF #define RX_PATH_GSM ( TX_SW_1 | TX_SW_2 | TX_SW_3) #define RX_PATH_DCS (DCS_RX_EN | TX_SW_1 | TX_SW_2 | TX_SW_3) #define RX_PATH_PCS (PCS_RX_EN | TX_SW_1 | TX_SW_3) #define TX_PATH_GSM ( TX_SW_1 | TX_SW_2 ) #define TX_PATH_DCS ( TX_SW_2 | TX_SW_3) #define TX_PATH_PCS (DCS_RX_EN | TX_SW_2 | TX_SW_3) #define TC1_DEVICE_ABB TC1_DEVICE0 #define TC1_DEVICE_RF TC1_DEVICE1 #define TC1_DEVICE_PLL TC1_DEVICE2 #define TC1_DEVICE_DATA_OUT TC1_DEVICE3 //todo: read data from rf and do stuff #endif typedef struct { UWORD16 data[6]; UWORD16 enable; UWORD16 index; UWORD16 write_index; } T_PLL_TUNING; extern T_PLL_TUNING pll_tuning; #ifdef TPUDRV35_C // Function prototypes SYS_UWORD16 Convert_l1_radio_freq(SYS_UWORD16 radio_freq); #endif