--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/src/cs/layer1/tm_cust0/l1tm_cust.h	Fri Oct 16 06:23:26 2020 +0000
@@ -0,0 +1,66 @@
+/************* Revision Controle System Header *************
+ *                  GSM Layer 1 software
+ * L1TM_CUST.H
+ *
+ *        Filename l1tm_cust.h
+ *  Copyright 2003 (C) Texas Instruments  
+ * 
+ ************* Revision Controle System Header *************/
+
+
+/*---------------------------------------------------------*/
+/* Initial settings for test mode config => Cust_tm_init() */
+/*---------------------------------------------------------*/
+
+// Control algorithm settings: 0=>OFF, 1=>ON
+#define AGC_ENABLE   1
+#define AFC_ENABLE   1
+
+// ADC conversion setting: 0=>OFF, 1=>ON
+#define ADC_ENABLE   1
+
+// AGC settings
+#define TM_AGC_VALUE   50   // AGC gain
+#define TM_LNA_OFF      0   // 0=>LNA ON, 1=>LNA OFF
+
+// Power measurement settings
+#define TM_NUM_MEAS     1  // number of measurements per TDMA
+#define TM_WIN_MEAS     1  // position of measurement within TDMA
+
+// BEACON and TCH settings
+#define TM_BCCH_ARFCN   80     // beacon 
+#define TM_TCH_ARFCN    62     // TCH arfcn
+#define TM_MON_ARFCN    33     // monitor arfcn
+#define TM_CHAN_TYPE    TCH_F  // channel type
+#define TM_SUB_CHAN      0     // subchannel number
+#define TM_SLOT_NUM      4     // TS number
+#define TM_TSC           5     // Training Sequence
+#define TM_TXPWR        15     // TXPWR setting
+#define TM_TXPWR_SKIP    4
+#define TM_TA            0     // timing advance setting
+#define TM_BURST_TYPE    0     // 0=>normal burst, 1=>RACH burst
+#define TM_BURST_DATA    0     // as defined in TM100.doc: tx_param_write
+#define TM_PM_ENABLE     1     // Enable power measurements in packet transfer mode
+
+// Statistics settings
+#define TM_NUM_LOOPS              0  // number of times a task is executed, 0 means infinite loop
+#define TM_AUTO_RESULT_LOOPS      0  // number of loops before stats result is returned, 0 means infinite
+#define TM_AUTO_RESET_LOOPS       0  // number of loops before stats I/F is reset, 0 means infinite
+#define TM_STAT_TYPE              1  // type of stats as defined in TM100.doc: stats_read
+#define TM_STAT_BITMASK      0x6057  // stats bitmaks as defined in TM100.doc: stats_read
+
+#if L1_GPRS
+  // Settings for GPRS test mode:
+  #define TM_PDTCH_ARFCN        62  // PDTCH arfcn
+  #define TM_MULTISLOT_CLASS     1  // GPRS multi slot class
+  #define TM_STAT_GPRS_SLOTS  0x80  // Bit mask for RX stats from PDTCH
+  #define TM_RX_ALLOCATION    0x80  // RX slot allocation (bit7->TS0...bit0->TS7)
+  #define TM_RX_CODING_SCHEME    1  // RX coding scheme
+  #define TM_TX_ALLOCATION    0x80  // TX slot allocation (bit7->TS0...bit0->TS7)
+  #define TM_TX_CODING_SCHEME    2  // TX coding scheme
+  #define TM_TXPWR_GPRS         15  // GPRS txpwr level
+#endif
+
+
+
+