--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/src/cs/layer1/tpu_drivers/source0/tpudrv35.h	Fri Oct 16 06:23:26 2020 +0000
@@ -0,0 +1,166 @@
+/****************** Revision Controle System Header ***********************
+ *                      GSM Layer 1 software                                
+ *              Copyright (c) Texas Instruments 2001                      
+ *                                                                        
+ *        Filename tpudrv35.h
+ *  Copyright 2003 (C) Texas Instruments  
+ *                                                                        
+ ****************** Revision Controle System Header ***********************/
+
+//TRF2253 definitions
+#define  WordAdd0000     0x000000	 //Main Configuration
+#define  AutoPDB         0x000080  //Auto Power Down - Uses PWDNB pin
+#define  AuxSel          0x030000	 //Auxiliary output pin use = LOCK Detect
+#define  WordAdd0011     0x000003	 //RF1 N Divider
+#define  WordAdd0100     0x000004	 //RF2 N Divider
+#define  WordAdd0101     0x000005	 //IF N Divider
+#define  RFPWR           0x000020	 //RF LO high power
+#define  XPDM            0x000100  //Reference amplifier ON when PWDNB pin = 0
+
+//TRF6053 definitions
+#define  Mode0           0x000000
+#define  Mode1           0x000001
+#define  Mode2           0x000003
+#define  Mode3           0x000005
+#define  Mode4           0x000007
+#define  LNAMixPwrOn     0x000080    //Mode0
+#define  VCODiv2PwrOn    0x000040    //Mode0
+#define  RXBBIFStgPwrOn  0x000020    //Mode0
+#define  OFFStrCalOn     0x000010    //Mode0
+#define  VCORDivPwrOn    0x000008    //Mode0
+#define  MixLOBuffPwrOn  0x000004    //Mode0
+#define  TXStagesPwrOn   0x000002    //Mode0
+
+#define  BandHigh        0x000008    //Mode1
+
+#define  LNAGainLow      0x000010    //Mode2
+#define  ChgPPLBNeg      0x000010    //Mode2
+#define  LowBIF610       0x000020    //Mode2
+#define  PreCCLBDis      0x000008    //Mode2
+
+#define  ChgPPHBNeg      0x000010    //Mode3
+#define  PreCCHBDis      0x000008    //Mode3
+#define  HighBIF412      0x000020    //Mode3
+#define  HighBIF25       0x000040    //Mode3
+#define  HighBIF410      0x000060    //Mode3
+
+#define  FreqDetDis      0x000400    //Mode4
+#define  IFVCOExternal   0x000200    //Mode4
+#define  IFPLLBuffDis    0x000100    //Mode4
+#define  LBandLNAExt     0x000080    //Mode4
+#define  HBandLNAExt     0x000040    //Mode4
+#define  Div2ToRXStgs    0x000020    //Mode4
+#define  DivRToTXStgs    0x000010    //Mode4
+
+/*------------------------------------------*/
+/*        Download delay values             */
+/*------------------------------------------*/
+#define TRF6053_DOWNLOAD_TIME   15
+#define SYNTH_DOWNLOAD_TIME     20
+
+//--------------------------------------------
+// internal tpu timing
+//--------------------------------------------
+
+#define DLT_1     1   // 1 tpu instruction = 1 qbit
+#define DLT_2     2 
+#define DLT_3     3 
+#define DLT_4     4
+ 
+#define DLT_1B    4   // 3*move + 1*byte (download)
+#define DLT_2B    6   // 4*move + 2*byte
+#define DLT_3B    8   // 5*move + 3*byte
+
+#define SL_SU_DELAY1 4  // No. bits to send + load data to shift + send write cmd + 1
+#define SL_SU_DELAY2 3  // load data to shift + send write cmd + 1
+#define SL_SU_DELAY3 5  // SL_SU_DELAY1 + serialization
+
+/*------------------------------------------*/
+/*        Download delay values             */
+/*------------------------------------------*/
+// 0.9230769 usec ~ 1 qbit i.e. 200 usec is ~ 217 qbit
+
+#define T TPU_CLOCK_RANGE  // TODO: should be a define from L1. 
+ 
+// time below are offset to when BDLENA goes low
+#define TRF_R13  (     5 - DLT_1B )          // disable rx path, fe, lna_gain
+#define TRF_R11 (    0 - DLT_1B)           // disable BDLON & BDLENA
+#define TRF_R10 (  - 5 - DLT_1B)           // disable TRF6053
+
+// burst data comes here
+// time below are offset to when BDLENA goes high
+#define TRF_R9   (PROVISION_TIME -   0 - DLT_1B) // enable BDLENA, disable BDLCAL
+#define TRF_R8   (PROVISION_TIME -  11 - DLT_1B) // set rx path + power on RX front end, DC cal. off
+#define TRF_R7   (PROVISION_TIME -  65 - DLT_1B) // enable BDLCAL
+#define TRF_R6   (PROVISION_TIME -  72 - DLT_1B) // enable BDLON
+#define TRF_R5   (PROVISION_TIME -  76 - DLT_1B) // power on receiver, start DC cal.
+#define TRF_R4   (PROVISION_TIME -  80 - DLT_2B) // set RX gain & band.
+                                                 // ADC read, uses min 11 qbit due to 5 wait 
+#define TRF_R3   (PROVISION_TIME - 196 - DLT_1B) // power up TRF2253
+#define TRF_R1   (PROVISION_TIME - 205 - DLT_3B) // set RF PLL N counter = r1 and IF PLL N counter in TRF2253 = r2
+
+// time below are offset to when BULENA goes low
+#define TRF_T14   (  34 - DLT_2)     // disable PA_ON, , BULON, fe, rx path & lna
+#define TRF_T13   (  29 - DLT_1B)    // disable TRF6053
+#define TRF_T12_1 (  21 - DLT_1B)    // disable fe_sw
+//#define TRF_T12   (  18 - DLT_1 )    // disable TSPACT01
+#define TRF_T11   (   0 - DLT_1B)    // disable BULENA
+#define TRF_T10_1 (- 40 - DLT_1B)    // ADC read
+// burst data comes here
+// time below are offset to when BULENA goes high
+#define TRF_T10_0 (+  27 - DLT_1B)   //enable PA_ON
+#define TRF_T10   (+  18 - DLT_1B)   // set fe 
+#define TRF_T9    (-   0 - DLT_1B)   // enable BULENA
+#define TRF_T8_1  (- 100 - DLT_1B)   // set TX_PCS_EN as required
+#define TRF_T8    (- 108 - DLT_2B)   // power on transceiver 
+#define TRF_T7    (- 115 - DLT_1B)   // disable BULCAL
+#define TRF_T6    (- 230 - DLT_1B)   // power up TRF2253
+#define TRF_T5    (- 233 - DLT_2B)   // set TX band in TRF6053
+#define TRF_T3    (- 249 - DLT_3B)   // set RF PLL N counter = t3 and IF PLL N counter in TRF2253 = t4
+#define TRF_T2    (- 260 - DLT_1B)   // enable BULCAL
+#define TRF_T1    (- 278 - DLT_1B)   // enable BULON
+
+#if ((BOARD == 34)||(BOARD == 35)) 
+
+  #define PA_ON      0x01     // act0
+  #define DCS_RX_EN  0x02     // act1
+  #define PCS_RX_EN  0x04     // act2
+  #define PCS_TX_EN  0x08     // act3
+  #define LNA_GAIN   0x10     // act4
+  #define TX_SW_1    0x20     // act5
+  #define TX_SW_2    0x40     // act6
+  #define TX_SW_3    0x80     // act7
+  #define TX_SW_OFF  (TX_SW_1 | TX_SW_2 | TX_SW_3)
+
+  #define ACT_OFF    TX_SW_OFF
+  
+  #define RX_PATH_GSM  (            TX_SW_1 | TX_SW_2 | TX_SW_3)
+  #define RX_PATH_DCS  (DCS_RX_EN | TX_SW_1 | TX_SW_2 | TX_SW_3)
+  #define RX_PATH_PCS  (PCS_RX_EN | TX_SW_1 |           TX_SW_3)
+
+  #define TX_PATH_GSM  (            TX_SW_1 | TX_SW_2          )
+  #define TX_PATH_DCS  (                      TX_SW_2 | TX_SW_3)
+  #define TX_PATH_PCS  (DCS_RX_EN |           TX_SW_2 | TX_SW_3)
+  
+  #define TC1_DEVICE_ABB      TC1_DEVICE0 
+  #define TC1_DEVICE_RF       TC1_DEVICE1
+  #define TC1_DEVICE_PLL      TC1_DEVICE2
+  #define TC1_DEVICE_DATA_OUT TC1_DEVICE3  //todo: read data from rf and do stuff
+#endif
+
+typedef struct 
+{
+  UWORD16  data[6];
+  UWORD16  enable;
+  UWORD16  index;
+  UWORD16  write_index;
+}
+T_PLL_TUNING;
+
+extern T_PLL_TUNING pll_tuning;
+
+#ifdef TPUDRV35_C
+// Function prototypes
+SYS_UWORD16 Convert_l1_radio_freq(SYS_UWORD16 radio_freq);
+
+#endif