FreeCalypso > hg > fc-tourmaline
view src/g23m-gprs/cci/cci.h @ 287:3dee79757ae4
UI fw: load handheld audio mode on boot
We have now reached the point where use of audio mode config files
should be considered mandatory. In ACI usage we can tell users that
they need to perform an AT@AUL of some appropriate audio mode, but
in UI-enabled fw we really need to have the firmware load audio modes
on its own, so that correct audio config gets established when the
handset or development board runs on its own, without a connected host
computer.
Once have FC Venus with both main and headset audio channels and
headset plug insertion detection, our fw will need to automatically
load the handheld mode or the headset mode depending on the plug
insertion state. For now we load only the handheld mode, which has
been tuned for FC-HDS4 on FC Luna.
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Sat, 13 Nov 2021 03:20:57 +0000 |
parents | fa8dc04885d8 |
children |
line wrap: on
line source
/* +----------------------------------------------------------------------------- | Project : | Modul : +----------------------------------------------------------------------------- | Copyright 2002 Texas Instruments Berlin, AG | All rights reserved. | | This file is confidential and a trade secret of Texas | Instruments Berlin, AG | The receipt of or possession of this file does not convey | any rights to reproduce or disclose its contents or to | manufacture, use, or sell anything it may describe, in | whole, or in part, without the specific written consent of | Texas Instruments Berlin, AG. +----------------------------------------------------------------------------- | Purpose : Definitions for entity CCI. +----------------------------------------------------------------------------- */ #ifndef CCI_H #define CCI_H #ifndef TI_PS_OP_CIPH_DRIVER #if !defined(_GEA_SIMULATION_) && !defined(LL_2to1) #include "config/board.cfg" #endif /* !_GEA_SIMULATION_ && !LL_2to1 */ /* * GEA-HW related constants */ #if (BOARD == 0 || BOARD == 50 || BOARD == 51 || BOARD == 52 || BOARD == 53) /* Dolo1-equipped boards, e.g. F-Sample/Dolo1 */ #define START_ADRESS 0xFFFE6800 /* address independent from bit mapping */ #else #if (BOARD == 61) /* G-Sample */ #define START_ADRESS 0xFFFB6800 /* address independent from bit mapping */ #else /* D-Sample, also in I-Sample */ #define START_ADRESS 0xFFFFC000 /* address independent from bit mapping */ #endif #endif /* * Macros */ /* CNTL_REG R/W flags */ #define RESET_UL 0x0001 /* check bit to get UL reset in progress */ #define RESET_DL 0x0002 /* check bit to get DL reset in progress */ #define NRESET_UL ~(RESET_UL) /* mask to init HW reset in UL direction */ #define NRESET_DL ~(RESET_DL) /* mask to init HW reset in DL direction */ #define START 0x0004 /* set bit to start HW module */ #define CL_ENABLE 0x0008 /* set bit to enable internal clock */ #define CL_DISABLE ~(CL_ENABLE) /* mask to disable internal clock */ #define UL_DL_DOWN 0x0010 /* set bit to select downlink direction */ #define UL_DL_UP ~(UL_DL_DOWN) /* mask to set uplink direktion */ #define IT_ENABLE 0x0020 /* set bit to enable HW interrupt */ #define IT_DISABLE ~(IT_ENABLE) /* mask to disable HW interrupt */ /* CONF_UL_REG1 and CONF_DL_REG1 R/W flags */ #define INPUT_SHIFT 0x0001 /* set bit to set ignore byte one flag */ #define NO_INPUT_SHIFT ~(INPUT_SHIFT) /* mask to clear ignore byte one flag */ #define ENCRYPT 0x0008 /* set bit to enable encryption */ #define NO_ENCRYPT ~(ENCRYPT) /* mask to disable encryption */ #define PROTECTED 0x0010 /* set bit to enable protection mode */ #define NON_PROTECTED ~(PROTECTED) /* mask to disable protection mode */ #define FCS_COMPUTED 0x0020 /* set bit to enable FCS computation */ #define FCS_NOT_COMPUTED ~(FCS_COMPUTED) /* mask to disable FCS computation */ #define D_DL 0x0040 /* set bit to enable HW in DL direction */ #define D_UL ~(D_DL) /* mask to enable HW in UL direction */ #define GEA_SECOND 0x0080 /* set bit to enable Second GEA algorithm */ #define GEA_FIRST ~(GEA_SECOND) /* mask to enable First GEA algorithm */ /* STATUS_REQ read only flags (R/W if _GEA_SIMULATION_ is set) */ #define CHECK_WORKING 0x0001 /* check bit to get TRUE if HW is working */ #define NOT_WORKING ~(CHECK_WORKING) /* mask to simulate HW is not working */ #define FCS_FALSE_BIT 0x0002 /* check bit to get TRUE if FSC is bad */ #endif /* TI_PS_OP_CIPH_DRIVER */ /*==== TYPES ======================================================*/ /* * CCI is embedded in LLC thus use llc_data instead of cci_data. * the CCI services must then be defined in llc_data, of course. */ #define cci_data llc_data /*==== EXPORT =====================================================*/ #endif /* CCI_H */