FreeCalypso > hg > fc-tourmaline

view src/cs/layer1/tm_cust0/l1tm_cust.h @ 221:5bf097aeaad7

Find changesets by keywords (author, files, the commit message), revision number or hash, or revset expression.
LLS: when turning off all LEDs on boot, skip LED-C Having LLS turn off LED-A and LED-B on boot is normally unnecessary (they should already be off in Iota), but it is harmless, hence this logic is kept for robustness. However, having LLS read-modify-write the BCICTL2 register (to turn off LED-C) creates a potential race condition with FCHG writes to this register, especially in the case when baseband switch-on is caused by VCHG and charging is expected to start right away. Furthermore, control of the charging LED itself (on those hw targets that have it) is the responsibility of the FCHG SWE, hence LLS should leave it alone.
author Mychaela Falconia <falcon@freecalypso.org>
date Mon, 26 Apr 2021 21:55:13 +0000
parents 4e78acac3d88
children
line wrap: on
line source

/************* Revision Controle System Header *************
 *                  GSM Layer 1 software
 * L1TM_CUST.H
 *
 *        Filename l1tm_cust.h
 *  Copyright 2003 (C) Texas Instruments  
 * 
 ************* Revision Controle System Header *************/


/*---------------------------------------------------------*/
/* Initial settings for test mode config => Cust_tm_init() */
/*---------------------------------------------------------*/

// Control algorithm settings: 0=>OFF, 1=>ON
#define AGC_ENABLE   1
#define AFC_ENABLE   1

// ADC conversion setting: 0=>OFF, 1=>ON
#define ADC_ENABLE   1

// AGC settings
#define TM_AGC_VALUE   50   // AGC gain
#define TM_LNA_OFF      0   // 0=>LNA ON, 1=>LNA OFF

// Power measurement settings
#define TM_NUM_MEAS     1  // number of measurements per TDMA
#define TM_WIN_MEAS     1  // position of measurement within TDMA

// BEACON and TCH settings
#define TM_BCCH_ARFCN   80     // beacon 
#define TM_TCH_ARFCN    62     // TCH arfcn
#define TM_MON_ARFCN    33     // monitor arfcn
#define TM_CHAN_TYPE    TCH_F  // channel type
#define TM_SUB_CHAN      0     // subchannel number
#define TM_SLOT_NUM      4     // TS number
#define TM_TSC           5     // Training Sequence
#define TM_TXPWR        15     // TXPWR setting
#define TM_TXPWR_SKIP    4
#define TM_TA            0     // timing advance setting
#define TM_BURST_TYPE    0     // 0=>normal burst, 1=>RACH burst
#define TM_BURST_DATA    0     // as defined in TM100.doc: tx_param_write
#define TM_PM_ENABLE     1     // Enable power measurements in packet transfer mode

// Statistics settings
#define TM_NUM_LOOPS              0  // number of times a task is executed, 0 means infinite loop
#define TM_AUTO_RESULT_LOOPS      0  // number of loops before stats result is returned, 0 means infinite
#define TM_AUTO_RESET_LOOPS       0  // number of loops before stats I/F is reset, 0 means infinite
#define TM_STAT_TYPE              1  // type of stats as defined in TM100.doc: stats_read
#define TM_STAT_BITMASK      0x6057  // stats bitmaks as defined in TM100.doc: stats_read

#if L1_GPRS
  // Settings for GPRS test mode:
  #define TM_PDTCH_ARFCN        62  // PDTCH arfcn
  #define TM_MULTISLOT_CLASS     1  // GPRS multi slot class
  #define TM_STAT_GPRS_SLOTS  0x80  // Bit mask for RX stats from PDTCH
  #define TM_RX_ALLOCATION    0x80  // RX slot allocation (bit7->TS0...bit0->TS7)
  #define TM_RX_CODING_SCHEME    1  // RX coding scheme
  #define TM_TX_ALLOCATION    0x80  // TX slot allocation (bit7->TS0...bit0->TS7)
  #define TM_TX_CODING_SCHEME    2  // TX coding scheme
  #define TM_TXPWR_GPRS         15  // GPRS txpwr level
#endif