FreeCalypso > hg > fc-tourmaline
view src/cs/drivers/drv_core/armio/armio.h @ 303:f76436d19a7a default tip
!GPRS config: fix long-standing AT+COPS chance hanging bug
There has been a long-standing bug in FreeCalypso going back years:
sometimes in the AT command bring-up sequence of an ACI-only MS,
the AT+COPS command would produce only a power scan followed by
cessation of protocol stack activity (only L1 ADC traces), instead
of the expected network search sequence. This behaviour was seen
in different FC firmware versions going back to Citrine, and seemed
to follow some law of chance, not reliably repeatable.
This bug has been tracked down and found to be specific to !GPRS
configuration, stemming from our TCS2/TCS3 hybrid and reconstruction
of !GPRS support that was bitrotten in TCS3.2/LoCosto version.
ACI module psa_mms.c, needed only for !GPRS, was missing in the TCS3
version and had to be pulled from TCS2 - but as it turns out,
there is a new field in the MMR_REG_REQ primitive that needs to be
set correctly, and that psa_mms.c module is the place where this
initialization needed to be added.
| author | Mychaela Falconia <falcon@freecalypso.org> |
|---|---|
| date | Thu, 08 Jun 2023 08:23:37 +0000 |
| parents | 4e78acac3d88 |
| children |
line wrap: on
line source
/* * ARMIO.H * * Control diagnostic bits * * Reference : GCS207 * */ #include "chipset.cfg" #include "l1sw.cfg" #if (OP_L1_STANDALONE == 0) #include "main/sys_types.h" #else #include "sys_types.h" #endif // Duplicate address with ARMIO_IO_CNTL // Need to investigate !!! //#define ARMIO_CNTL (MEM_ARMIO + 0x04) /* I/O control */ #define ARMIO_IN (MEM_ARMIO + 0x00) /* inputs */ #define ARMIO_OUT (MEM_ARMIO + 0x02) /* outputs */ #define ARMIO_IO_CNTL (MEM_ARMIO + 0x04) /* I/O control */ #define ARMIO_CNTL_REG (MEM_ARMIO + 0x06) /* control ARMIO */ #define ARMIO_LOAD_TIM (MEM_ARMIO + 0x08) /* load TIM */ #if (CHIPSET != 12) #define ARMIO_KBR_IN (MEM_ARMIO + 0x0A) /* KBR inputs (rows) */ #define ARMIO_KBR_OUT (MEM_ARMIO + 0x0C) /* KBR outputs (columns) */ #endif #define ARMIO_PWM_CNTL (MEM_ARMIO + 0x0E) /* LIGHT/BUZZER control */ #define ARMIO_LIGHT (MEM_ARMIO + 0x10) /* light value */ #define ARMIO_BUZZER (MEM_ARMIO + 0x12) /* buzzer value */ #define ARMIO_CLOCKEN 0x0020 #if (CHIPSET != 12) #define CLKM_IO_CNTL MEM_IO_SEL /* control IO */ #endif #if (CHIPSET == 12) #define GPIO_INTERRUPT_LEVEL_REG * (volatile SYS_UWORD16 *) (MEM_ARMIO + 0x16) #define GPIO_INTERRUPT_MASK_REG * (volatile SYS_UWORD16 *) (MEM_ARMIO + 0x18) #else #define ARMIO_GPIO_EVENT_MODE (MEM_ARMIO + 0x14) /* GPIO event mode */ #define ARMIO_KBD_GPIO_INT (MEM_ARMIO + 0x16) /* Kbd/GPIO IRQ register */ #define ARMIO_KBD_GPIO_MASKIT (MEM_ARMIO + 0x18) /* Kbd/GPIO mask IRQ */ // CC test 0316 #define ARMIO_GPIO_DEBOUNCE (MEM_ARMIO + 0x1A) /* GPIO debounceing register*/ // end #endif #if (CHIPSET != 12) #define ARMIO_DCD (2) /* IO used for DCD on C-Sample - Output */ #endif #define ARMIO_DTR (3) /* IO used for DTR on C-Sample - Input */ #define ARMIO_FALLING_EDGE (0) #define ARMIO_RISING_EDGE (1) #if (CHIPSET != 12) #define ARMIO_KEYPDAD_INT (0x0001) #define ARMIO_GPIO_INT (0x0002) #define ARMIO_MASKIT_KBD (0x0001) #define ARMIO_MASKIT_GPIO (0x0002) void AI_EnableBit(int bit); void AI_DisableBit(int bit); #endif void AI_SetBit(int bit); void AI_ResetBit(int bit); void AI_ConfigBitAsOutput(int bit); void AI_ConfigBitAsInput(int bit); SYS_BOOL AI_ReadBit(int bit); void AI_SetSimIO3V(SYS_UWORD8 StdOutput); #if (OP_L1_STANDALONE == 0) void AI_Power(SYS_UWORD8 power); #endif void AI_ResetTspIO(void); void AI_ResetDbgReg(void); void AI_ResetIoConfig(void); void AI_InitIOConfig(void); void AI_ClockEnable (void); void AI_SelectIOForIT (SYS_UWORD16 Pin, SYS_UWORD16 Edge); #if (CHIPSET != 12) int AI_CheckITSource (SYS_UWORD16 Source); #endif void AI_UnmaskIT (SYS_UWORD16 Source); void AI_MaskIT (SYS_UWORD16 Source);