FreeCalypso > hg > fc-usbser-tools
comparison doc/DUART28-EEPROM-config @ 34:f5fbcf1ff032
doc: initial import from freecalypso-hwlab
| author | Mychaela Falconia <falcon@freecalypso.org> |
|---|---|
| date | Sat, 09 Sep 2023 21:28:02 +0000 |
| parents | |
| children | dbaf239436cf |
comparison
equal
deleted
inserted
replaced
| 33:df284688d0c8 | 34:f5fbcf1ff032 |
|---|---|
| 1 The EEPROM on the DUART28 adapter board has two valid configurations: DUART28C | |
| 2 and DUART28S. As of this writing the S configuration is the default shipping | |
| 3 one, but this situation may change in the future. The difference between the | |
| 4 two configs is in the USB VID:PID presented by the USB device, and this USB ID | |
| 5 difference has the following practical impact: | |
| 6 | |
| 7 * The C configuration presents a custom USB ID and requires a custom patch to | |
| 8 the Linux kernel ftdi_sio driver in order to work - without this ftdi_sio | |
| 9 driver patch it won't work at all. But if you do go through the pain of | |
| 10 applying the needed patch to your Linux kernel ftdi_sio driver, the reward | |
| 11 is that you get not only the two Calypso UARTs, but also working boot control | |
| 12 outputs. | |
| 13 | |
| 14 * The S configuration presents the default FT2232x USB ID and is therefore | |
| 15 supported out of the box by the standard Linux ftdi_sio driver without needing | |
| 16 any patches. However, the adapter's CTL1 and CTL2 outputs cannot be used in | |
| 17 this configuration (they will be bogusly asserted whenever Channel B ttyUSB | |
| 18 device is opened), and thus they must be left unconnected, and you don't get | |
| 19 to play with the remote boot control feature. | |
| 20 | |
| 21 The physical hardware is identical between the two configurations, only the | |
| 22 EEPROM programming changes, thus end users need to be able to switch freely | |
| 23 between the two EEPROM configs as they wish. This article explains how to | |
| 24 program the EEPROM back and forth between the two configs. | |
| 25 | |
| 26 Determining your current DUART28 config | |
| 27 ======================================= | |
| 28 | |
| 29 Connect the USB cable between your DUART28 board and your Linux host, and | |
| 30 observe dmesg output. If your DUART28 board is in the C configuration, it will | |
| 31 present as USB ID 0403:7152, and if it is in the S config, it will present as | |
| 32 USB ID 0403:6010. You can also see these USB IDs with lsusb. The product ID | |
| 33 string is also programmed as "DUART28C" or "DUART28S". | |
| 34 | |
| 35 Converting from DUART28S to DUART28C | |
| 36 ==================================== | |
| 37 | |
| 38 If your DUART28 board is currently in the S config, its USB ID will be | |
| 39 0403:6010, which is the default ID for FTDI's two-channel FT2232x family. | |
| 40 Because it is the standard default, there are plenty of other gadgets using the | |
| 41 same ID - thus you need to ensure that you have no other USB devices with the | |
| 42 same ID connected to your system during the reprogramming operation. Run lsusb | |
| 43 and ensure that you see only one USB device with ID 0403:6010. Ensure that this | |
| 44 one device really is your DUART28 board: unplug that USB cable and make sure | |
| 45 that the device disappears, plug it back in and make sure that it reappears. | |
| 46 | |
| 47 One you have confirmed that you won't inadvertently hit some other FT2232x | |
| 48 device, execute the actual programming command as follows (from the top | |
| 49 directory of this code repository): | |
| 50 | |
| 51 ftee-gen2232c eeproms/duart28c $Serial | fteeprom-prog i:0x0403:0x6010 | |
| 52 | |
| 53 (See FTDI-EEPROM-tools article for other ways to specify the target device to | |
| 54 fteeprom-prog.) | |
| 55 | |
| 56 Replace the $Serial metavariable with the 3-digit serial number of your DUART28 | |
| 57 adapter board as it appears on the factory serial number sticker. | |
| 58 | |
| 59 After this operation completes successfully, unplug and replug the USB cable | |
| 60 between the DUART28 board and your host - the adapter should now show up with | |
| 61 USB ID 0403:7152. | |
| 62 | |
| 63 Converting from DUART28C to DUART28S | |
| 64 ==================================== | |
| 65 | |
| 66 If your DUART28 board is currently in the C config, its USB ID will be | |
| 67 0403:7152, which is a private ID that belongs to us and should not be used by | |
| 68 other parties. The reverse conversion command is as follows: | |
| 69 | |
| 70 ftee-gen2232c eeproms/duart28s $Serial | fteeprom-prog i:0x0403:0x7152 |