freecalypso-citrine: bsp/abb+spi/abb.h comparison

comparison bsp/abb+spi/abb.h @ 0:75a11d740a02

initial import of gsm-fw from freecalypso-sw rev 1033:5ab737ac3ad7

author	Mychaela Falconia <falcon@freecalypso.org>
date	Thu, 09 Jun 2016 00:02:41 +0000
parents
children

comparison

equal deleted inserted replaced

--1:000000000000
+:75a11d740a02
+/******************************************************************************/
+/*          TEXAS INSTRUMENTS INCORPORATED PROPRIETARY INFORMATION            */
+/*                                                                            */
+/* Property of Texas Instruments -- For  Unrestricted  Internal  Use  Only    */
+/* Unauthorized reproduction and/or distribution is strictly prohibited.  This*/
+/* product  is  protected  under  copyright  law  and  trade  secret law as an*/
+/* unpublished work.  Created 1987, (C) Copyright 1997 Texas Instruments.  All*/
+/* rights reserved.                                                           */
+/*                                                                            */
+/*                                                                            */
+/* Filename         : abb.h                                                   */
+/*                                                                            */
+/* Description      : Analog BaseBand registers and bits definition.	      */
+/*                    Functions to drive the ABB device.                      */
+/*                    The Serial Port Interface is used to connect the TI     */
+/*		      Analog BaseBand (ABB).   				      */
+/*		      It is assumed that the ABB is connected as the SPI      */
+/*                    device 0.                                               */
+/*									      */
+/* Author           : Pascal PUEL                                             */
+/*                                                                            */
+/* Version number   : 1.3                                                     */
+/*                                                                            */
+/* Date and time    : 08/22/03						      */
+/*                                                                            */
+/* Previous delta   : Creation                                                */
+/*                                                                            */
+/******************************************************************************/
+#ifndef __ABB_H__
+#define __ABB_H__
+#include "../../include/config.h"
+#include "../../include/sys_types.h"
+#ifndef _WINDOWS
+/*------------------------------------*/
+/* SYREN PG Definition                */
+/*------------------------------------*/
+#if (ANALOG == 3)   // SYREN
+#define S_PG_10      1
+#define S_PG_20      2
+#endif  // (ANALOG == 3)
+// DEFINITIONS FOR OMEGA/NAUSICA
+#if (ANALOG == 1)
+// ABB PAGE
+#define PAGE0	0x0001
+#define PAGE1	0x0002
+// ABB REGISTERS
+//=== PAGE 0 =======
+#define PAGEREG      (1  << 1)
+#define APCDEL1      (2  << 1)
+#define BULDATA1_2   (3  << 1)
+#define TOGBR1       (4  << 1)
+#define TOGBR2       (5  << 1)
+#define VBDCTRL      (6  << 1)
+#define AUXAFC1      (7  << 1)
+#define AUXAFC2      (8  << 1)
+#define AUXAPC       (9  << 1)
+#define APCRAM       (10 << 1)
+#define APCOFF       (11 << 1)
+#define AUXDAC       (12 << 1)
+#define MADCCTRL1    (13 << 1)
+#define MADCCTRL2    (14 << 1)
+#define VBATREG      (15 << 1)
+#define VCHGREG      (16 << 1)
+#define ICHGREG      (17 << 1)
+#define VBKPREG      (18 << 1)
+#define ADIN1REG     (19 << 1)
+#define ADIN2REG     (20 << 1)
+#define ADIN3REG     (21 << 1)
+#define ADIN4XREG    (22 << 1)
+#define ADIN5YREG    (23 << 1)
+#define MADCSTAT     (24 << 1)
+#define CHGREG       (25 << 1)
+#define ITMASK       (26 << 1)
+#define ITSTATREG    (27 << 1)
+#define BCICTL1      (28 << 1)
+#define BCICTL2      (29 << 1)
+#define VRPCCTL2     (30 << 1)
+#define VRPCSTS      (31 << 1)
+//=== PAGE 1 =======
+#define PAGEREG      (1  << 1)
+#define BULIOFF      (2  << 1)
+#define BULQOFF      (3  << 1)
+#define BULQDAC      (4  << 1)
+#define BULIDAC      (5  << 1)
+#define BBCTRL       (6  << 1)
+#define VBUCTRL      (7  << 1)
+#define VBCTRL       (8  << 1)
+#define PWDNRG       (9  << 1)
+#define TSC_TIMER    (10 << 1)
+#define VRPCCTRL3    (11 << 1)
+#define APCOUT       (12 << 1)
+#define VRPCBGT      (18 << 1)
+#define TAPCTRL      (19 << 1)
+#define TAPREG       (20 << 1)
+#define AFCCTLADD    (21 << 1)
+#define AFCOUT       (22 << 1)
+#define VRPCCTRL1    (23 << 1)
+#define VRPCCTRL4    (24 << 1)
+#define APCDEL2      (26 << 1)
+#define ITSTATREG    (27 << 1)
+// Registers bit definitions
+// ABB device bits definition of register VBCTRL
+#define VDLAUX    0x001
+#define VDLEAR    0x002
+#define VBUZ      0x004
+#define VULSWITCH 0x008
+#define MICBIAS   0x010
+#define VALOOP    0x020
+#define VCLKMODE  0x040
+#define VSYNC     0x080
+#define VBDFAUXG  0x100
+#define VFBYP     0x200
+// ABB device bits definition of register VBUCTRL
+#define DXEN      0x200
+// ABB device bits definition of register VRPCSTS
+#define ONBSTS    0x01  // ON Button push flag
+#define ONRSTS    0x02  // Remote ON flag
+#define ITWSTS    0x04  // Wake-up IT flag
+#define CHGSTS    0x08  // Charger plug flag
+#define ONREFLT   0x10  // ON Button current state
+#define ORMRFLT   0x20  // Remote ON current state
+#define CHGPRES   0x40  // Charger plug current state
+// ABB device bits definition of register ITSTATREG
+#define REMOT_IT_STS    0x02
+#define PUSHOFF_IT_STS  0x04
+#define CHARGER_IT_STS  0x08
+#define ADCEND_IT_STS   0x20
+// On Nausica, if the PWR key is pressed, the bit is set, and cleared when released
+#define PWR_OFF_KEY_PRESSED       (ONREFLT)
+// ABB ADC Interrupts
+#define EOC_INTENA  0x03DF
+#define EOC_INTMASK 0x0020
+// ABB ADC CHANNELS
+#define VBATCV      0x0001
+#define VCHGCV      0x0002
+#define ICHGCV      0x0004
+#define VBKPCV      0x0008
+#define ADIN1CV     0x0010
+#define ADIN2CV     0x0020
+#define ADIN3CV     0x0040
+#define vADIN4XCV   0x0080
+#define ADIN5XCV    0x0100
+#define ALL         0x01FF
+#define NONE        0x0000
+// ABB MODULES
+#define MADC        0x8000
+#define AFC         0x2000
+#define ADAC        0x0800
+#define DCDC        0x0080
+#define ALLOFF      0x0000
+// Definitions of OMEGA test modes for baseband windows
+#define TSPTEST1       0x001d
+#define TSPTEST2       0x001e
+#define AFCTEST        0x0010
+#define AFCNORM        0x0000
+// DEFINITIONS FOR IOTA
+#elif (ANALOG == 2)
+// ABB PAGE
+#define PAGE0	0x0001
+#define PAGE1	0x0002
+#define PAGE2	0x0010
+// ABB REGISTERS
+//=== PAGE 0 =======
+#define PAGEREG      (1  << 1)
+#define APCDEL1      (2  << 1)
+#define BULDATA1_2   (3  << 1)
+#define TOGBR1       (4  << 1)
+#define TOGBR2       (5  << 1)
+#define VBDCTRL      (6  << 1)
+#define AUXAFC1      (7  << 1)
+#define AUXAFC2      (8  << 1)
+#define AUXAPC       (9  << 1)
+#define APCRAM       (10 << 1)
+#define APCOFF       (11 << 1)
+#define AUXDAC       (12 << 1)
+#define MADCCTRL     (13 << 1)
+#define VBATREG      (15 << 1)
+#define VCHGREG      (16 << 1)
+#define ICHGREG      (17 << 1)
+#define VBKPREG      (18 << 1)
+#define ADIN1REG     (19 << 1)
+#define ADIN2REG     (20 << 1)
+#define ADIN3REG     (21 << 1)
+#define ADIN4REG     (22 << 1)
+#define MADCSTAT     (24 << 1)
+#define CHGREG       (25 << 1)
+#define ITMASK       (26 << 1)
+#define ITSTATREG    (27 << 1)
+#define BCICTL1      (28 << 1)
+#define BCICTL2      (29 << 1)
+#define VRPCDEV      (30 << 1)
+#define VRPCSTS      (31 << 1)
+//=== PAGE 1 =======
+#define PAGEREG      (1  << 1)
+#define BULIOFF      (2  << 1)
+#define BULQOFF      (3  << 1)
+#define BULQDAC      (4  << 1)
+#define BULIDAC      (5  << 1)
+#define BBCTRL       (6  << 1)
+#define VBUCTRL      (7  << 1)
+#define VBCTRL1      (8  << 1)
+#define PWDNRG       (9  << 1)
+#define VBPOP        (10 << 1)
+#define VBCTRL2      (11 << 1)
+#define APCOUT       (12 << 1)
+#define BCICONF      (13 << 1)
+#define BULGCAL      (14 << 1)
+#define TAPCTRL      (19 << 1)
+#define TAPREG       (20 << 1)
+#define AFCCTLADD    (21 << 1)
+#define AFCOUT       (22 << 1)
+#define VRPCSIM      (23 << 1)
+#define AUXLED       (24 << 1)
+#define APCDEL2      (26 << 1)
+#define ITSTATREG    (27 << 1)
+#define VRPCMSKABB   (29 << 1)
+#define VRPCCFG      (30 << 1)
+#define VRPCMSK      (31 << 1)
+// Registers bit definitions
+// ABB device bits definition of register VBCTRL1
+#define VDLAUX    0x001
+#define VDLEAR    0x002
+#define VBUZ      0x004
+#define VULSWITCH 0x008
+#define MICBIAS   0x010
+#define VALOOP    0x020
+#define VCLKMODE  0x040
+#define VSYNC     0x080
+#define VBDFAUXG  0x100
+#define VFBYP     0x200
+// ABB device bits definition of register VBCTRL2
+#define MICBIASEL 0x001
+#define VDLHSO    0x002
+#define MICNAUX   0x004
+// ABB device bits definition of register VBUCTRL
+#define DXEN      0x200
+// ABB device bits definition of register VBPOP
+#define HSODIS    0x001
+#define HSOCHG    0x002
+#define HSOAUTO   0x004
+#define EARDIS    0x008
+#define EARCHG    0x010
+#define EARAUTO   0x020
+#define AUXDIS    0x040
+#define AUXCHG    0x080
+#define AUXAUTO   0x100
+// ABB device bits definition of register VRPCSTS
+#define ONBSTS    0x01  // ON Button push flag
+#define ONRSTS    0x02  // Remote ON flag
+#define ITWSTS    0x04  // Wake-up IT flag
+#define CHGSTS    0x08  // Charger plug flag
+#define ONREFLT   0x10  // ON Button current state
+#define ORMRFLT   0x20  // Remote ON current state
+#define CHGPRES   0x40  // Charger plug current state
+// ABB device bits definition of register ITSTATREG
+#define REMOT_IT_STS    0x02
+#define PUSHOFF_IT_STS  0x04
+#define CHARGER_IT_STS  0x08
+#define ADCEND_IT_STS   0x20
+// On Iota, the bit is set when the key is released and set when the key is pressed
+#define PWR_OFF_KEY_PRESSED      (0)
+// ABB ADC Interrupts
+#define EOC_INTENA  0x03DF
+#define EOC_INTMASK 0x0020
+// ABB ADC CHANNELS
+#define VBATCV      0x0001
+#define VCHGCV      0x0002
+#define ICHGCV      0x0004
+#define VBKPCV      0x0008
+#define ADIN1CV     0x0010
+#define ADIN2CV     0x0020
+#define ADIN3CV     0x0040
+#define ADIN4CV     0x0080
+#define ALL         0x00FF
+#define NONE        0x0000
+// ABB MODULES
+#define MADC        0x8000
+#define AFC         0x2000
+#define ADAC        0x0800
+#define DCDC        0x0080
+#define ALLOFF      0x0000
+// Definitions of IOTA test modes
+#define TSPTEST1      0x001d
+#define TSPTEST2      0x001e
+#define AFCTEST       0x0010
+#define AFCNORM       0x0000
+// Definition for IOTA test modes
+#define TSPEN         0x001a
+#define MADCTEST      0x0012
+#define TSPADC        0x0015
+#define TSPUP         0x0017
+#define TSPDN         0x0018
+// Definition for IOTA Power Management
+//The duration of the SLPDLY counter must be greater than the process execution time:
+//DBB deep sleep routine included the IT check = DBB sleep routine and IT check
+//+ the seven 32Khz clock cycle interval needed to ABB in order to make effective the sleep abort write access in VRPCDEV    ++  //  register -> 7*T32Khz = = ABB IBIC propagation delay
+//+ 150us of short asynchronous wake-up time  (approximately 4*T32Khz) = ULPD short sleep where Syren/IOTA aborts sleep and
+//  write DEVSLEEP = 0
+#define SLPDLY                0x001F    // delay to set IOTA in sleep mode (unit: 20*T32Khz)
+#define MASK_SLEEP_MODE       0x0000    // set the regulators in low consumption in sleep mode
+// DEFINITIONS FOR SYREN
+#elif (ANALOG == 3)
+// ABB PAGE
+#define PAGE0	0x0001
+#define PAGE1	0x0002
+#define PAGE2	0x0010
+// ABB REGISTERS
+//=== PAGE 0 =======
+#define PAGEREG     (1  << 1)
+#define APCDEL1     (2  << 1)
+#define BULDATA1_2  (3  << 1)
+#define TOGBR1      (4  << 1)
+#define TOGBR2      (5  << 1)
+#define VBDCTRL     (6  << 1)
+#define AUXAFC1     (7  << 1)
+#define AUXAFC2     (8  << 1)
+#define AUXAPC      (9  << 1)
+#define APCRAM      (10 << 1)
+#define APCOFF      (11 << 1)
+#define AUXDAC      (12 << 1)
+#define MADCCTRL    (13 << 1)
+#define CHGIREG     (14 << 1)
+#define VBATREG     (15 << 1)
+#define VCHGREG     (16 << 1)
+#define ICHGREG     (17 << 1)
+#define VBKPREG     (18 << 1)
+#define ADIN1REG    (19 << 1)
+#define ADIN2REG    (20 << 1)
+#define ADIN3REG    (21 << 1)
+#define ADIN4REG    (22 << 1)
+#define ADIN5REG    (23 << 1)
+#define MADCSTAT    (24 << 1)
+#define CHGVREG     (25 << 1)
+#define ITMASK      (26 << 1)
+#define ITSTATREG   (27 << 1)
+#define BCICTL1     (28 << 1)
+#define BCICTL2     (29 << 1)
+#define VRPCDEV     (30 << 1)
+#define VRPCSTS     (31 << 1)
+//=== PAGE 1 =======
+#define PAGEREG     (1  << 1)
+#define BULIOFF     (2  << 1)
+#define BULQOFF     (3  << 1)
+#define BULQDAC     (4  << 1)
+#define BULIDAC     (5  << 1)
+#define BBCTRL      (6  << 1)
+#define VBUCTRL     (7  << 1)
+#define VBCTRL1     (8  << 1)
+#define PWDNRG      (9  << 1)
+#define VBPOP       (10 << 1)
+#define VBCTRL2     (11 << 1)
+#define APCOUT      (12 << 1)
+#define BCICONF     (13 << 1)
+#define BULGCAL     (14 << 1)
+#define VAUDCTRL    (15 << 1)
+#define VAUSCTRL    (16 << 1)
+#define VAUOCTRL    (17 << 1)
+#define VAUDPLL     (18 << 1)
+#define TAPCTRL     (19 << 1)
+#define TAPREG      (20 << 1)
+#define AFCCTLADD   (21 << 1)
+#define AFCOUT      (22 << 1)
+#define VRPCSIMR    (23 << 1)
+#define BCIWDOG     (24 << 1)
+#define NONE8       (25 << 1)
+#define APCDEL2     (26 << 1)
+#define ITSTATREG   (27 << 1)
+#if (ANLG_PG == S_PG_20)                           // SYREN PG2.0 ON EVACONSO
+#define BBCFG       (28 << 1)
+#else
+#define NONE9       (28 << 1)
+#endif
+#define VRPCMSKOFF  (29 << 1)
+#define VRPCCFG     (30 << 1)
+#define VRPCMSKSLP  (31 << 1)
+//=== PAGE 2 =======
+#if (ANLG_PG == S_PG_10)       // SYREN PG1.0 ON ESAMPLE
+#define BBCFG       (5 << 1)
+#endif
+#define VRPCABBTST  (25 << 1)
+#define VRPCAUX     (30 << 1)
+#define VRPCLDO     (31 << 1)
+/* INSERT HERE OTHER DEVICES REGISTERS */
+// Registers bit definitions
+/*** SYREN internal control bits ***/
+/** For reg. VBCTRL1 **/
+#define VULSWITCH 0x008
+#define MICBIAS   0x010
+#define VALOOP    0x020
+#define VCLKMODE  0x040
+#define VSYNC     0x080
+#define VBDFAUXG  0x100
+#define VFBYP     0x200
+/** For reg. VBCTRL2 **/
+#define HSMICSEL  0x001
+#define MICBIASEL 0x004
+#define SPKG      0x008
+#define HSOVMID   0x010
+#define HSDIF     0x020
+/** For reg. VBUCTRL **/
+#define DXEN      0x200
+/** For reg. VBPOP **/
+#define HSODIS    0x001
+#define HSOCHG    0x002
+#define HSOAUTO   0x004
+#define EARDIS    0x008
+#define EARCHG    0x010
+#define EARAUTO   0x020
+#define AUXFDIS   0x040
+#define AUXAUTO   0x080
+#define AUXFBYP   0x200
+// ABB device bits definition of register VRPCCFG
+#define PWOND     0x20  // ON Button current state
+#define CHGPRES   0x40
+// ABB device bits definition of register ITSTATREG
+#define REMOT_IT_STS    0x02
+#define PUSHOFF_IT_STS  0x04
+#define CHARGER_IT_STS  0x08
+#define ADCEND_IT_STS   0x20
+// ABB device bits definition of register VRPCSTS
+#define ITWSTS    0x10   // Wake-up IT flag
+#define PWONBSTS  0x20   // ON Button push flag
+#define CHGSTS    0x40   // Charger plug flag
+#define RPSTS     0x100  // Remote ON flag
+// ABB ADC Interrupts
+#define EOC_INTENA  0x03DF
+#define EOC_INTMASK 0x0020
+// ABB ADC CHANNELS (reg. MADCCTRL)
+#define VBATCV    0x0001
+#define VCHGCV    0x0002
+#define ICHGCV    0x0004
+#define VBKPCV    0x0008
+#define ADIN1CV   0x0010
+#define ADIN2CV   0x0020
+#define ADIN3CV   0x0040
+#define ADIN4CV   0x0080
+#define ADIN5CV   0x0100
+#define ALL       0x01FF
+#define NONE      0x0000
+// ABB MODULES
+#define MADC        0x8000
+#define AFC         0x2000
+#define ADAC        0x0800
+#define DCDC        0x0080
+#define ALLOFF      0x0000
+// Definitions of SYREN test modes
+#define TSPTEST1      0x001d
+#define TSPTEST2      0x001e
+#define AFCTEST       0x0010
+#define AFCNORM       0x0000
+#define TSPEN         0x001a
+#define MADCTEST      0x0012
+#define TSPADC        0x0015
+#define TSPUP         0x0017
+#define TSPDN         0x0018
+// Definition for SYREN Power Management
+//The duration of the SLPDLY counter must be greater than the process execution time:
+//DBB deep sleep routine included the IT check = DBB sleep routine and IT check
+//+ the seven 32Khz clock cycle interval needed to ABB in order to make effective the sleep abort write access in VRPCDEV    ++  //  register -> 7*T32Khz = = ABB IBIC propagation delay
+//+ 150us of short asynchronous wake-up time  (approximately 4*T32Khz) = ULPD short sleep where Syren/IOTA aborts sleep and
+//  write DEVSLEEP = 0
+#define SLPDLY             0x001F    // delay to set SYREN in sleep mode (unit: 20*T32Khz)
+#define MASK_SLEEP_MODE    0x0000    // set the regulators in low consumption in sleep mode
+#define LOCORE_SLEEP   0x01
+#define NORMAL_SLEEP   0x00
+#define MAIN_BG        0x01,
+#define SLEEP_BG       0x00
+#endif	  // ANALOG == 1,2,3
+// Define the level of semaphore protection for all accesses to the ABB
+// 0 for no protection
+// 1 for protection low
+// 2 for protection medium
+// 3 for protection high
+#if (OP_L1_STANDALONE == 1)
+#define ABB_SEMAPHORE_PROTECTION     (0)
+#else
+#define ABB_SEMAPHORE_PROTECTION     (1)
+#endif
+// PROTOTYPES
+#if (ABB_SEMAPHORE_PROTECTION)
+void ABB_Sem_Create(void);
+#endif
+void ABB_Wait_IBIC_Access(void);
+void ABB_Write_Register_on_page(SYS_UWORD16 page, SYS_UWORD16 reg_id, SYS_UWORD16 value);
+SYS_UWORD16 ABB_Read_Register_on_page(SYS_UWORD16 page, SYS_UWORD16 reg_id);
+void ABB_free_13M(void);
+void ABB_stop_13M(void);
+SYS_UWORD16 ABB_Read_Status(void);
+void ABB_Conf_ADC(SYS_UWORD16 Channels, SYS_UWORD16 ItVal);
+void ABB_Read_ADC(SYS_UWORD16 *Buff);
+void ABB_on(SYS_UWORD16 modules, SYS_UWORD8 bRecoveryFlag);
+SYS_UWORD32 ABB_sleep(SYS_UWORD8 sleep_performed, SYS_WORD16 afc);
+void ABB_wakeup(SYS_UWORD8 sleep_performed, SYS_WORD16 afc);
+void ABB_wa_VRPC(SYS_UWORD16 value);
+void ABB_Write_Uplink_Data(SYS_UWORD16 *TM_ul_data);
+#if (OP_L1_STANDALONE == 0)
+void ABB_Power_Off(void);
+#endif
+#if (ANALOG ==3)
+void Syren_Sleep_Config(SYS_UWORD16 sleep_type,SYS_UWORD16 bg_select, SYS_UWORD16 sleep_delay);
+#endif
+#else    // _WINDOWS
+// DEFINITIONS FOR IOTA
+// ABB PAGE
+#define PAGE0	0x0001
+#define PAGE1	0x0002
+#define PAGE2	0x0010
+// ABB REGISTERS
+//=== PAGE 0 =======
+#define PAGEREG      (1  << 1)
+#define APCDEL1      (2  << 1)
+#define BULDATA1_2   (3  << 1)
+#define TOGBR1       (4  << 1)
+#define TOGBR2       (5  << 1)
+#define VBDCTRL      (6  << 1)
+#define AUXAFC1      (7  << 1)
+#define AUXAFC2      (8  << 1)
+#define AUXAPC       (9  << 1)
+#define APCRAM       (10 << 1)
+#define APCOFF       (11 << 1)
+#define AUXDAC       (12 << 1)
+#define MADCCTRL     (13 << 1)
+#define VBATREG      (15 << 1)
+#define VCHGREG      (16 << 1)
+#define ICHGREG      (17 << 1)
+#define VBKPREG      (18 << 1)
+#define ADIN1REG     (19 << 1)
+#define ADIN2REG     (20 << 1)
+#define ADIN3REG     (21 << 1)
+#define ADIN4REG     (22 << 1)
+#define MADCSTAT     (24 << 1)
+#define CHGREG       (25 << 1)
+#define ITMASK       (26 << 1)
+#define ITSTATREG    (27 << 1)
+#define BCICTL1      (28 << 1)
+#define BCICTL2      (29 << 1)
+#define VRPCDEV      (30 << 1)
+#define VRPCSTS      (31 << 1)
+//=== PAGE 1 =======
+#define PAGEREG      (1  << 1)
+#define BULIOFF      (2  << 1)
+#define BULQOFF      (3  << 1)
+#define BULQDAC      (4  << 1)
+#define BULIDAC      (5  << 1)
+#define BBCTRL       (6  << 1)
+#define VBUCTRL      (7  << 1)
+#define VBCTRL1      (8  << 1)
+#define PWDNRG       (9  << 1)
+#define VBPOP        (10 << 1)
+#define VBCTRL2      (11 << 1)
+#define APCOUT       (12 << 1)
+#define BCICONF      (13 << 1)
+#define BULGCAL      (14 << 1)
+#define TAPCTRL      (19 << 1)
+#define TAPREG       (20 << 1)
+#define AFCCTLADD    (21 << 1)
+#define AFCOUT       (22 << 1)
+#define VRPCSIM      (23 << 1)
+#define AUXLED       (24 << 1)
+#define APCDEL2      (26 << 1)
+#define ITSTATREG    (27 << 1)
+#define VRPCMSKABB   (29 << 1)
+#define VRPCCFG      (30 << 1)
+#define VRPCMSK      (31 << 1)
+// ABB device bits definition of register VBUCTRL
+#define DXEN      0x200
+// ABB device bits definition of register VRPCSTS
+#define ONBSTS    0x01  // ON Button push flag
+#define ONRSTS    0x02  // Remote ON flag
+#define ITWSTS    0x04  // Wake-up IT flag
+#define CHGSTS    0x08  // Charger plug flag
+#define ONREFLT   0x10  // ON Button current state
+#define ORMRFLT   0x20  // Remote ON current state
+#define CHGPRES   0x40  // Charger plug current state
+// ABB device bits definition of register ITSTATREG
+#define REMOT_IT_STS    0x02
+#define PUSHOFF_IT_STS  0x04
+#define CHARGER_IT_STS  0x08
+#define ADCEND_IT_STS   0x20
+// PROTOTYPES
+void ABB_Write_Register_on_page(SYS_UWORD16 page, SYS_UWORD16 reg_id, SYS_UWORD32 value);
+SYS_UWORD16 ABB_Read_Register_on_page(SYS_UWORD16 page, SYS_UWORD16 reg_id);
+SYS_UWORD16 ABB_Read_Status(void);
+void ABB_Conf_ADC(SYS_UWORD16 Channels, SYS_UWORD16 ItVal);
+void ABB_Read_ADC(SYS_UWORD16 *Buff);
+#endif  // _WINDOWS
+#endif // __ABB_H__

FreeCalypso > hg > freecalypso-citrine

comparison bsp/abb+spi/abb.h @ 0:75a11d740a02