FreeCalypso > hg > freecalypso-docs
annotate TCH-tap-modes @ 106:28c1cb869d91
TCH-tap-modes: updates for TCH/HS
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Mon, 22 Jul 2024 22:36:29 +0000 |
parents | 8a45cd92e3c3 |
children | dfa5f99631a6 |
rev | line source |
---|---|
95
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
1 It has been discovered that the DSP ROM in the Calypso GSM baseband processor |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
2 makes it possible to "tap" into speech traffic on GSM traffic channels (TCH): |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
3 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
4 1) In the downlink direction, the signal processing chain which every GSM MS |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
5 must implement includes a GSM 05.03 channel decoder, operating in one of |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
6 several variants as necessary for each supported TCH mode, followed by speech |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
7 decoders for each supported codec. TI's DSP naturally implements this |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
8 required signal processing chain, and this implementation includes one nifty |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
9 feature: the bits that make up the internal interface from GSM 05.03 channel |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
10 decoder output to the input of speech decoders are written into the NDB API |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
11 RAM page that is also accessible to the ARM core, and these bits can be |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
12 externally read out. The act of reading these bits is completely |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
13 non-invasive (we are only reading bits that are already there, not modifying |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
14 anything), thus we can sniff TCH downlink on any voice call in real time |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
15 without disrupting or impacting standard type-approved GSM MS operation in |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
16 any way. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
17 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
18 2) In the uplink direction, there is a reverse signal processing chain in which |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
19 the output of the internal speech encoder for the selected codec feeds into |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
20 the input of the corresponding GSM 05.03 channel encoder. In this direction |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
21 there are two tapping possibilities: |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
22 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
23 2a) There is a buffer in the NDB API RAM page from which one can read the bits |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
24 that pass from the speech encoder output to the channel encoder input - |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
25 let's call this form of TCH tap "uplink sniffing"; |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
26 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
27 2b) There is a special mode in which the output of the internal speech encoder |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
28 is effectively suppressed and the input to the channel encoder comes from |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
29 another NDB API RAM buffer that needs to be filled by ARM firmware - let's |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
30 call this form of TCH tap "uplink substitution". |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
31 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
32 Sources of knowledge about these DSP functions |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
33 ============================================== |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
34 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
35 For the functions of TCH DL sniffing (tap 1 in the above summary) and TCH UL |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
36 substitution (tap 2b in the above summary), the primary source of knowledge is |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
37 the defunct '#if TRACE_TYPE==3' code in TSM30 and LoCosto L1 sources. I call |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
38 this code defunct because the TRACE_TYPE preprocessor symbol is set to 4 (not 3) |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
39 in both TCS211 and LoCosto versions, and appears to be set to 0 (all trace |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
40 disabled) in the ancient TSM30 build. This code appears to be some very old |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
41 test mode, apparently sending some test bit patterns into TCH UL and expecting |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
42 the same bit patterns back on TCH DL, presumably with a test instrument such as |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
43 CMU200 providing a loopback from UL to DL on this test TCH, and has only |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
44 survived in an incomplete form: |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
45 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
46 * There are '#if TRACE_TYPE==3' stanzas in l1_cmplx.c, in both TSM30 and LoCosto |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
47 versions, that implement DSP buffer writing for TCH UL substitution (TCH/F |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
48 only) and timing control for TCH DL buffer reading (both TCH/F and TCH/H), |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
49 calling a function named play_trace() for the latter. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
50 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
51 * There is no play_trace() code in the LoCosto source. but there is an |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
52 hw_debug.c source module in the TSM30 code drop under MCU/Layer1/L1c/Src, |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
53 and it contains (presumed) TI-legacy play_trace() and play_diagnostics() |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
54 functions, once again under '#if (TRACE_TYPE==3)'. play_trace() reads the |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
55 DSP's TCH DL buffer and saves the bits in an ARM firmware RAM buffer, and |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
56 then play_diagnostics() analyzes the captured booty - and studying the second |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
57 function is how we learn the apparent original intent of doing test bit |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
58 patterns on TCH. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
59 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
60 * The code that feeds "UL play" test bit patterns to the earlier-mentioned |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
61 '#if TRACE_TYPE==3' TCH UL substitution code in l1_cmplx.c (apparently once |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
62 hacked into dll_read_dcch() and tx_tch_data()) has not been found anywhere. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
63 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
64 For TCH tap 2a in our summary at the beginning of this article (non-invasive |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
65 sniffing of TCH UL bits produced by the internal speech encoder) there does not |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
66 exist any authoritative source of knowledge. It naturally follows from |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
67 otherwise-known Calypso DSP architecture that these internally produced TCH UL |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
68 bits should reside in the "main" a_du_0 buffer (or in a_du_1 when TCH/H |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
69 subchannel 1 is active), and I (Mother Mychaela) have heard an anecdotal report |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
70 (from someone who once worked with Calypso in a non-community-based manner) that |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
71 these UL bits could indeed be read out of this buffer - but in the absence of |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
72 an authoritative source, we don't know when would be the correct time to read |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
73 this buffer. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
74 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
75 In our current state of knowledge, only TCH DL sniffing can be exercised safely: |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
76 for UL sniffing we don't know the correct time when the buffer would need to be |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
77 read, while active UL substitution is obviously an invasive hack involving a DSP |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
78 debug or test feature that is never used in standard GSM MS operation. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
79 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
80 Support for different speech codecs |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
81 =================================== |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
82 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
83 When it comes to passively sniffing TCH DL and/or UL, we are merely reading bits |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
84 that are already there, and basic reasoning tells us that the DSP's DL and UL |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
85 buffers involved in this exercise exist in all speech TCH modes supported by |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
86 the DSP: FR1, HR1, EFR and AMR. However: |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
87 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
88 * The ancient '#if TRACE_TYPE==3' reference code exists only for FR1, HR1 and |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
89 EFR - it clearly predates the addition of AMR in the later Calypso DSP |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
90 versions. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
91 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
92 * FR1, HR1 and EFR are the only codecs for which we (FreeCalypso community) know |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
93 the format in which TCH DL bits appear in the DSP's a_dd_0 and a_dd_1 buffers. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
94 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
95 * I (Mother Mychaela) have heard an anecdotal report (from the same |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
96 non-community-based party mentioned earlier) that TCH DL bits could be read |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
97 out of a_dd_0 buffer in TCH/AFS (AMR) mode - but I never got any details. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
98 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
99 In contrast with passive sniffing, active TCH UL substitution requires explicit |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
100 support from the DSP - and this explicit DSP support is known to exist for |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
101 certain only for TCH/FS and TCH/EFS channel modes, i.e., for FR1 and EFR codecs |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
102 only. In the case of TCH/HS channel mode (HR1 codec), it *appears* that the DSP |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
103 supports UL substitution in this mode too, but this combination has only been |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
104 exercised by OsmocomBB people (the original '#if TRACE_TYPE==3' code for UL play |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
105 only supports TCH/F), and FreeCalypso policy is to treat everything coming out |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
106 of OBB as highly suspect. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
107 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
108 What about AMR? The anecdotal report (from the same already-mentioned party) is |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
109 that TCH UL substitution that works for FR1 and EFR appears to NOT work for AMR |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
110 - that's all I know - but frankly speaking, given that it's a weird DSP debug |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
111 mode that is never needed in standard GSM MS operation, I find it more |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
112 surprising that it works for FR1 and EFR than the observation that it doesn't |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
113 work for AMR. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
114 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
115 FreeCalypso support for TCH tap functions |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
116 ========================================= |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
117 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
118 TCH DL sniffing and UL substitution provisions were initially implemented in |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
119 FreeCalypso back in 2016, but only in the Citrine version, which was deemed to |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
120 be a dead end later that same year. However, this functionality is now being |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
121 resurrected, and it has been incorporated into our production FC Tourmaline |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
122 firmware as of 2022-12-13. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
123 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
124 In order to activate the function of TCH DL sniffing and save the recording of a |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
125 TCH DL session into a file, one needs to use the fc-shell utility from FC host |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
126 tools, specifically the tch record command in an interactive fc-shell session. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
127 The format in which TCH DL tap traffic is passed over RVTMUX (an original |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
128 FreeCalypso invention) has changed in a slight but incompatible way between the |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
129 original hackish version from 2016 and the new production version as of 2022, |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
130 and capturing TCH DL with new firmware requires the updated version of fc-shell |
106
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
131 that was released as part of fc-host-tools-r18. The current (developed in late |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
132 2022) incarnation of FreeCalypso TCH DL sniffing feature supports FR1, HR1 and |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
133 EFR codecs; initially only FR1 and EFR were tested, but in 2024 HR1 joined the |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
134 tested and known-working set. |
95
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
135 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
136 The function of TCH UL substitution is currently implemented in FC Tourmaline |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
137 only for FR1 and EFR (no HR1, no AMR), and it likewise requires running an |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
138 interactive fc-shell session in which you would invoke the tool's tch play |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
139 command. In the case of TCH UL play feature there has been NO change in the |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
140 RVTMUX transport format between 2016 and 2022 versions. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
141 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
142 TCH DL DSP buffers and capture format |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
143 ===================================== |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
144 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
145 The DSP's NDB API page has two buffers in which TCH DL bits appear: a_dd_0 and |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
146 a_dd_1. All TCH/F modes use a_dd_0, but TCH/H uses one buffer or the other |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
147 depending on the subchannel: subchannel 0 uses a_dd_0, subchannel 1 uses a_dd_1. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
148 (It is certainly a strange design - the DSP won't be able to receive and decode |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
149 the "wrong" subchannel because it doesn't know the ciphering key for the other |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
150 MS - but perhaps the designers of this DSP architecture aeons ago found this |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
151 design to somehow flow more naturally with their scheduling of DSP tasks.) Each |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
152 buffer consists of 22 16-bit words - they were originally 20 words, but then |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
153 extended to 22 words to support CSD 14.4 kbps mode. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
154 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
155 Each TCH buffer in the DSP's NDB API page consists of 3 status or header words |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
156 followed by N words of payload, where N depends on TCH mode: 17 for TCH/FS and |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
157 TCH/EFS, 8 for TCH/HS, and not-yet-studied for AMR and CSD. Let's begin our |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
158 analysis with the 3 status words that make up the buffer header: |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
159 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
160 Status word 0 (a_dd_0[0] or a_dd_1[0]) is a word of flag bits. We don't know |
106
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
161 the meaning of every bit in this word, but here are the bit meanings we've been |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
162 able to figure out so far, looking at TCH/FS, TCH/EFS and more recently TCH/HS |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
163 DL captures: |
95
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
164 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
165 * Bit 15 (B_BLUD) is a "buffer filled" or "data present" flag. This flag is |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
166 observed as 1 in *almost* every 20 ms window in which a traffic frame is |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
167 expected (fn_report_mod13_mod4 == 0 in l1s_read_dedic_dl(), case TCHTF), |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
168 except for certain instances early in the call setup process which remain to |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
169 be studied. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
170 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
171 * Bit 14 (B_AF) will be set if the block of 8 half-bursts (block diagonal |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
172 interleaving of GSM 05.03) corresponding to this buffer was channel-decoded |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
173 as speech rather than as FACCH - see further analysis below. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
174 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
175 * Bit 9 (B_ECRC) has only ever been observed as 1 when B_AF is set, i.e., when |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
176 the speech-not-FACCH channel decoder was invoked. In the case of TCH/EFS this |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
177 bit is set to 1 if the EFR-added CRC-8 was bad, and cleared if this CRC-8 was |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
178 good; in the case of TCH/FS this bit has always been observed as 1 and should |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
179 be ignored because there is no CRC-8 in TCH/FS. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
180 |
106
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
181 (Update for TCH/HS: in this channel mode this bit has always been observed |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
182 as 0.) |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
183 |
95
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
184 * Bit 7 has always been observed as 1 wheneven B_BLUD is set but B_AF is |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
185 cleared, i.e., whenever the block was channel-decoded in FACCH rather than |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
186 speech mode. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
187 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
188 * Bits 6:5 indicate the result of FIRE decoding in the event that the FACCH |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
189 decoder was invoked. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
190 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
191 * Bits 4:3 carry the ternary SID flag encoded as in section 6.1.1 of GSM 06.31 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
192 and 06.81, but only when the speech-not-FACCH channel decoder was invoked as |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
193 indicated by B_AF. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
194 |
106
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
195 (Update for TCH/HS: these bits apply to HR codec too, following GSM 06.41 |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
196 section 6.1.1 now.) |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
197 |
95
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
198 * Bit 2 is BFI as defined in section 6.1.1 of GSM 06.31 and 06.81. Whenever |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
199 the block was decoded as FACCH (bit 14 clear, bit 7 set), bit 2 has always |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
200 been observed as set, agreeing with the stipulation in GSM 06.31 and 06.81 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
201 that BFI=1 whenever a FACCH frame has been received. However, in the case of |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
202 TCH/EFS it appears that CRC-8 status (reported in bit 9) is NOT factored into |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
203 the logic that sets bit 2 - it appears that the subsequent speech decoding |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
204 logic is expected to OR bits 2 and 9 together to get the BFI flag for the Rx |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
205 DTX handler of GSM 06.81. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
206 |
106
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
207 (Update for TCH/HS: bit 2 is BFI in HR codec too.) |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
208 |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
209 * Bit 1 is seen only in TCH/HS, and appears to be the elusive BCI flag whose |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
210 existence has been figured out from ETSI GSM 06.06 reid.c source. See this |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
211 article for more information: |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
212 |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
213 https://osmocom.org/projects/retro-gsm/wiki/HRv1_error_flags |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
214 |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
215 * Bit 0 is UFI for TCH/HS only. |
28c1cb869d91
TCH-tap-modes: updates for TCH/HS
Mychaela Falconia <falcon@freecalypso.org>
parents:
95
diff
changeset
|
216 |
95
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
217 In the case of 20 ms blocks (reassembled from 8 half-bursts) that were channel- |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
218 decoded as speech rather than FACCH, the observed behavior is that bits 15 and |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
219 14 are set, the payload portion of the buffer is filled with the output from the |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
220 channel decoder, and bits 4:3 are set from this payload by the bit-counting rule |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
221 of section 6.1.1 of GSM 06.31 and 06.81 irrespective of the good-or-bad status |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
222 in bits 2 and 9. However, when bit 14 is clear and bit 7 is set, indicating |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
223 that the block (from 8 half-bursts) was channel-decoded in FACCH mode, the |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
224 following additional behavior is observed: |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
225 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
226 * The payload portion of the buffer remains unchanged from its previous content, |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
227 last written when a frame was channel-decoded in speech-not-FACCH mode; |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
228 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
229 * Bit 2 is set, bit 9 is cleared; |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
230 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
231 * Bits 4:3 are cleared even when they previously indicated SID based on the bit |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
232 pattern in the payload portion of the buffer, even when that SID-encoding |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
233 payload is still there. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
234 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
235 In the standard TCH DL signal processing chain, GSM 05.03 channel decoding is |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
236 followed by the Rx DTX handler of GSM 06.31 or 06.81 for TCH/FS or TCH/EFS, |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
237 respectively. It appears that the Rx DTX handler implemented in TI's DSP is |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
238 driven by this status word 0 at the head of the buffer, and we can only guess |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
239 as to its exact logic. At this point it bears reminding that the functions of |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
240 the Rx DTX handler are not rigidly prescribed in the specs: in the case of EFR |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
241 the bit-exact reference implementation is normative only in certain aspects |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
242 (e.g., comfort noise generation after receiving SID), but is considered a non- |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
243 normative example in some other key aspects (all GSM 06.61 functions, including |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
244 what happens when a FACCH block was received when speech frames were expected), |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
245 and in the case of FR1 there is no bit-exact reference implementation at all, |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
246 only general guidance. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
247 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
248 Having the curiosity of a cat, I (Mother Mychaela) naturally desire to know |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
249 exactly how the Rx DTX handler (the bridge between the channel decoder and the |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
250 speech decoder) works in TI's DSP. A full static reversing job on the DSP ROM |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
251 would provide complete answers, but is a very daunting proposition, thus I am |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
252 also looking at the idea of behavioral analysis: the output of the speech |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
253 decoder can be captured from MCSI on FCDEV3B hardware, or from the VSP tap on |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
254 FC Venus if we ever build that board, and if we combine that speech decoder |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
255 output capture with the currently-discussed capture of TCH DL buffers, we may |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
256 be able to glean some insight into the workings of the Rx DTX handler block: we |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
257 could implement a candidate Rx DTX handler clone in software and compare the |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
258 output (of this proposed handler followed by the spec-defined speech decoder) |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
259 against the actual speech output from the DSP. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
260 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
261 Back to our exposition of TCH DL buffer content: |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
262 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
263 Status word 1 (a_dd_0[1] or a_dd_1[1]) is some kind of DSP measurement or count |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
264 which Calypso ARM fw does not need to look at, except when debugging - the only |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
265 code which I (Mother Mychaela) could find that does anything with this DSP |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
266 status word is the ancient play_diagnostics() code in the TSM30 version |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
267 (obviously never included in any production fw); this code looks at the unknown |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
268 word in question and calls it "D_MACC". This play_diagnostics() code compares |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
269 the D_MACC reading against a threshold, and if the per-block reading is below |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
270 the threshold, an error message is printed. That's all we know! |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
271 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
272 Status word 2 (a_dd_0[2] or a_dd_1[2]) is a bit error count: the code in |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
273 l1s_read_dedic_dl() reads this error count and uses it for RXQUAL computation |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
274 for measurement reports. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
275 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
276 If one's area of interest is in replicating Rx DTX handling and speech decoding |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
277 that happens in the DSP, status words 1 and 2 can probably be ignored - instead |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
278 the important parts are status word 0 (extensively covered above) and the |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
279 payload portion of the buffer. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
280 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
281 The payload portion of the buffer consists of some number of 16-bit words: 17 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
282 of them for TCH/FS and TCH/EFS, or 8 of them for TCH/HS. The DSP does not have |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
283 any notion of 8-bit bytes, instead it operates on 16-bit words as its elementary |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
284 data unit. The ordering of bits within these 16-bit words (in the payload |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
285 portion of TCH buffers) is from the most-significant bit toward the least- |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
286 significant bit, thus when these TCH buffers are transferred via octet-oriented |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
287 interfaces, the upper byte of each word should be transferred first, even though |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
288 this byte order is counter to the little-endian byte order of the Calypso ARM |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
289 core. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
290 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
291 In the case of TCH/FS and TCH/EFS, the fill order of bits in the payload words |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
292 is as follows, starting with the most-significant bit of buffer word 3 (first |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
293 word of the payload portion): |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
294 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
295 * 182 bits of class 1; |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
296 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
297 * 4 dummy bits (always observed as 0); |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
298 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
299 * 78 bits of class 2; |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
300 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
301 * the last 8 bits of a_dd_0[19] are unused. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
302 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
303 In the case of TCH/HS, the fill order is similar, but modified as appropriate |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
304 for TCH/HS: |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
305 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
306 * 95 bits of class 1; |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
307 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
308 * 4 dummy bits; |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
309 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
310 * 17 bits of class 2; |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
311 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
312 * the last 12 bits of a_dd_0[10] or a_dd_1[10] are unused. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
313 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
314 Aside from the insertion of 4 extra dummy bits at the boundary between class 1 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
315 and class 2, the overall bit order is that of GSM 05.03 Figure 1 interface 1. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
316 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
317 In the case of TCH/EFS, the following additional considerations apply: |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
318 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
319 * Bits [65:73] in all received DL frames, where CRC-8 would go in the 260-bit |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
320 frame of GSM 05.03 interface 1 for EFR, are always observed as 0, whether |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
321 this CRC-8 was good (a_dd_0[0] bit 9 clear) or bad (a_dd_0[0] bit 9 set). |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
322 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
323 * The handling of repetition bits (4 bits of 244-bit EFR codec frame, each of |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
324 which is triplicated in the channel encoding for transmission) is unclear. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
325 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
326 Further detail regarding the repetition bits of TCH/EFS: distinct bit positions |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
327 exist in the 260-bit frame of GSM 05.03 interface 1 (which is the frame format |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
328 in the TCH buffers of TI's DSP) for each of the 3 copies of each of the 4 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
329 triplicated bits. It is obvious that correct decoding of these triplicated bits |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
330 requires a majority-vote function just like the one implemented in TMR systems |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
331 in space gear - but it is not absolutely and unquestionably obvious where this |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
332 TMR voting function is implemented in the Rx processing chain of TI's DSP. It |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
333 *appears* that this majority-vote function has already been performed by the DSP |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
334 function that writes a_dd_0, and that the first bit position out of each group |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
335 of 3 holds the output of this voting function, so that the subsequent speech |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
336 decoder only needs to use those "cooked" bits - but there is this mystery: |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
337 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
338 * At certain times, particularly during the main part of a test call, TCH DL |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
339 buffer readouts contain zeros in the "extra" repetition bit positions: for |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
340 each group of 3 bits, the first will contain 0 or 1, but the other two will |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
341 always be 0. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
342 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
343 * At other times, seemingly in the beginning and ending parts of test calls, |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
344 TCH DL buffer readouts contain matching bit values in all 3 positions: for |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
345 each group of 3 bits, if the first bit is 0, the other two will also be 0, or |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
346 if the first bit is 1, then the other two will also be 1. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
347 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
348 One possibility is that the DSP applies the required majority-voting function, |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
349 writes its output into the first bit position of each group of 3, but then |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
350 sometimes (and not at other times) applies another function that writes the |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
351 voting function output into the remaining bit positions, perhaps for loopback |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
352 of TCH DL into TCH UL. More study is needed in this area. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
353 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
354 FreeCalypso file format for TCH DL captures |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
355 =========================================== |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
356 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
357 The file format written by fc-shell tch record command is ASCII hex, line-based, |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
358 with one line for every captured 20 ms window. The new format as of 2022 is: |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
359 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
360 * Each line begins with an FR, HR or EFR keyword indicating which variant of |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
361 TCH DL has been captured; |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
362 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
363 * This keyword is followed by 3 space-separated DSP status words, each written |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
364 as 4 hex digits; |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
365 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
366 * The main body of the frame is written as 33 (TCH/FS & TCH/EFS) or 15 (TCH/HS) |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
367 hex bytes, produced from the payload portion of the TCH DL buffer by turning |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
368 each 16-bit word into 2 bytes (MSB first) and discarding the last byte that |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
369 is unused (always 0); |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
370 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
371 * Each line ends with a frame number in decimal, specifically the value of |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
372 fn_mod_104 variable in the l1s_read_dedic_dl() function when the DSP buffer |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
373 was read. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
374 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
375 The addition of the frame number field allows these TCH DL captures to be |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
376 reconciled against the SACCH multiframe structure, which matters for the rules |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
377 of DTX. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
378 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
379 TCH UL substitution: open questions |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
380 =================================== |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
381 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
382 Moving from the mostly-understood realm of TCH DL capture into the much more |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
383 experimental realm of TCH UL substitution, we have some open questions: how does |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
384 this DSP special mode really work? Here is what we know: if we load externally |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
385 sourced speech frames into otherwise-unused a_du_1 DSP buffer at the time of |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
386 (fn_report_mod13_mod4 == 3), which is the same time when FACCH or CSD UL would |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
387 be expected, and set B_PLAY_UL bit in DSP NDB API word d_tch_mode, the speech |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
388 frame stream going to the other end of the call will be the one we feed into |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
389 a_du_1 instead of the one produced from the microphone input by the internal |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
390 speech encoder. But here are the parts we don't know: |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
391 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
392 * If one were to set B_PLAY_UL in d_tch_mode but not feed external UL input |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
393 into a_du_1 buffer at the needed time, what will happen? |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
394 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
395 * Vice-versa, if one were to load a_du_1 and set its B_BLUD bit without setting |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
396 B_PLAY_UL in d_tch_mode, what will happen? |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
397 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
398 * Can the frame stream fed into a_du_1 be encoded in DTX-enabled mode, including |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
399 SID frames? If this possibility is allowed, what magic bits would need to be |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
400 set where in order to get the correct behavior from the DSP's subsequent |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
401 burst-by-burst DTX logic? |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
402 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
403 TCH UL substitution: implemented PoC |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
404 ==================================== |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
405 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
406 Back in 2016 we implemented a proof-of-concept TCH UL play feature in |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
407 FreeCalypso (only for TCH/FS and TCH/EFS), and the same PoC has been retained |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
408 when the overall TCH tap facility has been mainlined in late 2022. Having this |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
409 highly experimental (not fit for production use) TCH UL play code present in our |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
410 current production fw is deemed acceptable because this code will never be |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
411 invoked unless the user sends TCH_ULBITS_REQ packets to the running fw via |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
412 RVTMUX - and if you do send such packets (via tch play command in an fc-shell |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
413 session or by any other means), you are leaving the realm of production-approved |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
414 functionality and entering the realm of wild experimentation. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
415 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
416 The PoC TCH UL play mechanism consists of a small buffer (holding up to 4 FR1 or |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
417 EFR frames) implemented in the ARM firmware; this buffer is filled by arriving |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
418 TCH_ULBITS_REQ packets and drained by the tchf_substitute_uplink() function |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
419 called from l1s_ctrl_tchtf(). Specifically, a flag named tch_ul_play_mode is |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
420 set when TCH_ULBITS_REQ input is received, telling l1s_ctrl_tchtf() to start |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
421 calling tchf_substitute_uplink() when (fn_report_mod13_mod4 == 3); the called |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
422 function drains an uplink frame from the ring buffer, writes it into the DSP's |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
423 a_du_1 buffer, sets B_PLAY_UL in d_tch_mode and sends a TCH_ULBITS_CONF packet |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
424 back to the host. If the ring buffer is empty, the function clears both |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
425 B_PLAY_UL and the firmware's tch_ul_play_mode flag, ending the special TCH UL |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
426 play mode. |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
427 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
428 This PoC mechanism is meant to be exercised with tch play command in an |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
429 interactive fc-shell session: this command reads an ASCII line-based uplink data |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
430 file and sends it to the firmware frame by frame, paced by TCH_ULBITS_CONF |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
431 packets from the target. The input to this command is a line-based ASCII hex |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
432 file similar to the format written by tch record, but simplified: each line is |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
433 just the 33-byte frame to be sent (in TI DSP buffer format, following GSM 05.03 |
8a45cd92e3c3
TCH-tap-modes: new article
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
434 interface 1), without any flags or status words or frame numbers. |