view venus/src/usb/usb_domain_buf.v @ 70:8bc2aa52fd23

manual RESET button new part: 260 g force, shorter actuator One of the main envisioned use cases for FC Venus is field demonstration: the board will be carried around, mounted on a sheet of acrylic or somesuch, it will have a battery and an antenna connected, there will be a test SIM with active service inserted, and the setup will be ready to demonstrate as a working phone at a moment's notice. But when a demo is not actively in progress, the fully assembled setup will be transported around in a big and loose ESD bag, and it will need to be equivalent to a traditional phone in its switched-off state: battery present, RTC keeping time, but not switched on all the time. Having a RESET button of the same keyswitch type as used for the regular keypad and PWON would cause a problem for such field transport scenarios: any spurious press of this button would cause a "misc boot" switch-on. Short spurious presses of PWON are filtered out by the firmware (automatic power-off if the button isn't held down long enough), but the same cannot be done for super-low-level nTESTRESET. However, a button with significantly greater operating force and a shorter actuator (not sticking out to the same height as the regular keypad buttons) should be much safer.
author Mychaela Falconia <falcon@freecalypso.org>
date Thu, 02 Dec 2021 22:40:39 +0000
parents 4722b265cb8c
children
line wrap: on
line source

/*
 * This module encapsulates the 74LVC541A buffer in the USB domain.
 */

module usb_domain_buf  (GND, P_3V3,
			Int_TxD, Int_RxD, Int_RTS, Int_CTS,
			Int_DTR, Int_DCD, Int_RI, Int_TxD2, Int_RxD2,
			Host_TxD, Host_RxD, Host_RTS, Host_CTS,
			Host_DTR, Host_DCD, Host_RI, Host_TxD2, Host_RxD2);

input GND, P_3V3;

input Int_TxD, Int_RTS, Int_DTR, Int_TxD2;
output Int_RxD, Int_CTS, Int_DCD, Int_RI, Int_RxD2;

output Host_TxD, Host_RTS, Host_DTR, Host_TxD2;
input Host_RxD, Host_CTS, Host_DCD, Host_RI, Host_RxD2;

/* buffer common part */

x541_common common (.Vcc(P_3V3),
		    .GND(GND),
		    .nOE1(GND),
		    .nOE2(GND)
	);

capacitor bypass_cap (P_3V3, GND);

/* input buffers */

buffer_slot_basic buf_RxD  (.A(Host_RxD),  .Y(Int_RxD));
buffer_slot_basic buf_CTS  (.A(Host_CTS),  .Y(Int_CTS));
buffer_slot_basic buf_DCD  (.A(Host_DCD),  .Y(Int_DCD));
buffer_slot_basic buf_RI   (.A(Host_RI),   .Y(Int_RI));
buffer_slot_basic buf_RxD2 (.A(Host_RxD2), .Y(Int_RxD2));

/* output buffers */

buffer_slot_basic buf_TxD  (.A(Int_TxD),  .Y(Host_TxD));
buffer_slot_basic buf_DTR  (.A(Int_DTR),  .Y(Host_DTR));
buffer_slot_basic buf_TxD2 (.A(Int_TxD2), .Y(Host_TxD2));

/* RTS direct pass-thru: use an 0402 0R jumper */
resistor jmp_RTS (Int_RTS, Host_RTS);

endmodule