--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/gsm-fw/L1/include/l1_confg.h	Tue Nov 12 05:35:48 2013 +0000
@@ -0,0 +1,983 @@
+/************* Revision Controle System Header *************
+ *                  GSM Layer 1 software
+ * L1_CONFG.H
+ *
+ *        Filename l1_confg.h
+ *  Copyright 2003 (C) Texas Instruments  
+ *
+ ************* Revision Controle System Header *************/
+
+#ifndef __L1_CONFG_H__
+#define __L1_CONFG_H__
+
+// Traces...
+// TRACE_TYPE == 1,2,3 are used in standalone mode (L2-L3 Simul) with USART
+// TRACE_TYPE == 4 is used on A-sample only (with UART): L1 + protocol stack
+// TRACE_TYPE == 1 -> L1/L3 interface trace
+// TRACE_TYPE == 2 -> Trace mode: ~33~~1~011...
+// TRACE_TYPE == 3 -> same as above (2) plus FER or stats trace
+// TRACE_TYPE == 4 -> L1/L3 interface trace on A-sample with protocol stack
+// TRACE_TYPE == 5 -> trace for full simulation
+// TRACE_TYPE == 6 -> CPU load trace for hisr
+// TRACE_TYPE == 7 -> CPU LOAD trace for layer 1 hisr for all TDMA. Output on
+//                    UART at 38400 bps =>
+//                    format : <hisr cpu value in microseconds> <frame number>
+
+// Code PB reported workaround
+//------------------------------
+
+
+// Code Version possible choices
+//------------------------------
+#define SIMULATION     1
+#define NOT_SIMULATION 2
+
+// RCL functions Version possible choices
+//------------------------------
+#define       POLL_FORCED     0
+#define       RLC_SCENARIO    1
+#define       MODEM_FLOW      2
+
+// possible choices for UART trace output
+//------------------------------
+#define       MODEM_UART     0
+#define       IRDA_UART      1
+#if (CHIPSET == 12)
+  #define     MODEM2_UART    2
+#endif
+
+//============
+// CODE CHOICE
+//============
+#if 0
+#if (OP_L1_STANDALONE==0)
+#define CODE_VERSION NOT_SIMULATION
+#else // OP_L1_STANDALONE
+#ifdef WIN32
+#define CODE_VERSION  SIMULATION
+#else // WIN32
+#define CODE_VERSION  NOT_SIMULATION
+#endif // WIN32
+#endif // OP_L1_STANDALONE
+#endif // #if 0
+
+/* FreeCalypso */
+#define	CODE_VERSION	NOT_SIMULATION
+#define	AMR		1
+#define	L1_12NEIGH	1
+#define	L1_EOTD		0
+#define	L1_GTT		0
+#define	MELODY_E2	1
+#define	TESTMODE	1
+
+#if CONFIG_GPRS
+#  define L1_GPRS	1
+#else
+#  define L1_GPRS	0
+#endif
+
+//---------------------------------------------------------------------------------
+// Test with full simulation.
+//---------------------------------------------------------------------------------
+#if (CODE_VERSION == SIMULATION)
+
+  // Test Scenari...
+  #define SCENARIO_FILE          1  // Test Scenario comes from input files.
+  #define SCENARIO_MEM           0  // Test Scenario comes from RAM.
+
+  // Traces...
+  #undef TRACE_TYPE
+  #define TRACE_TYPE             5
+  #define LOGFILE_TRACE          1  // trace in an output logfile
+  #define FLOWCHART              0  // Message sequence/flow chart trace.
+  #define NUCLEUS_TRACE          0  // Nucleus error trace
+  #define EOTD_TRACE             1  // EOTD log trace
+  #define TRACE_FULL_NAME        0  // display full fct names after a PM/COM error
+
+  #define L2_L3_SIMUL            1  // Layer 2 & Layer 3 simulated, main within NU_MAIN.C, trace possible.
+
+  // Control algorithms...
+  #define AFC_ALGO               1  // AFC algorithm.
+  #define TOA_ALGO               1  // TOA algorithm.
+  #define AGC_ALGO               1  // AGC algorithm.
+  #define TA_ALGO                0  // TA (Timing Advance) algorithm.
+  #undef VCXO_ALGO
+  #define VCXO_ALGO              0  // VCXO algo
+  #undef DCO_ALGO
+  #define DCO_ALGO               0  // DCO algo (TIDE)
+  #undef ORDER2_TX_TEMP_CAL
+  #define ORDER2_TX_TEMP_CAL     0  // TX Temperature Compensation Algorithm selection
+
+
+  #define FACCH_TEST             0  // FACCH test enabled.
+
+  #define ADC_TIMER_ON           0  // Timer for ADC measurements
+  #define AFC_ON                 1  // Enable of the Omega AFC module
+
+  #define AUDIO_TASK             1  // Enable the L1 audio features
+  #define AUDIO_SIMULATION       1  // Audio simulator for the audio tasks (works only with the new audio design i.e. AUDIO_TASK=1)
+  #define AUDIO_L1_STANDALONE    0  // Flag to enable the audio simulator used with the L1 stand-alone (works only with the new audio design i.e. AUDIO_TASK=1)
+
+  #define GTT_SIMULATION         1  // Gtt simulator for the gtt tasks (works only with if L1_GTT=1)
+  #define TTY_SYNC_MCU           1  // TTY WORKAROUND BUG03401
+  #define TTY_SYNC_MCU_2         1  // 
+  #define L1_GTT_FIFO_TEST_ATOMIC 0 //
+  #define NEW_WKA_PATCH          0
+  #define OPTIMISED              1
+
+  #define L1_RECOVERY            0  // L1 recovery
+
+  #undef L1_GPRS
+  #define L1_GPRS                1  // GPRS L1: MS supporting both Circuit Switched and Packet (GPRS) capabilities
+
+  #undef AMR
+  #define AMR                    1  // AMR version 1.0 supported
+
+  #undef L1_12NEIGH
+  #define L1_12NEIGH             1  // new L1-RR interface for 12 neighbour cells
+
+  #undef L1_GTT
+  #define L1_GTT                 1  // Enable Global Text Telephony feature for simulation
+
+  #undef  OP_L1_STANDALONE
+  #define OP_L1_STANDALONE       1  // Selection of code for L1 stand alone
+
+  #undef  OP_RIV_AUDIO
+  #define OP_RIV_AUDIO           0  // Selection of code for Riviera audio
+
+  #undef OP_WCP
+  #define OP_WCP                 0  // No WCP integration
+//---------------------------------------------------------------------------------
+// Test with H/W platform.
+//---------------------------------------------------------------------------------
+#elif (CODE_VERSION == NOT_SIMULATION)
+
+  #define WA_PCTM_AGC_PARAMS 0 // to work by default with 4 parameters to calibration (compatible with PCTM if 1) 
+  // Work around about Calypso RevA: the bus is floating (Cf PB01435)
+  // (corrected with Calypso ReV B and Calypso C035)
+  #if (CHIPSET == 7)
+    #define W_A_CALYPSO_BUG_01435 1
+  #else
+    #define W_A_CALYPSO_BUG_01435 0
+  #endif
+
+
+  // for AMR thresolds definition CQ22226
+  #define AMR_THRESHOLDS_WORKAROUND 1
+
+  #if (L1_GTT==1)
+    #define TTY_SYNC_MCU 1
+    #define TTY_SYNC_MCU_2 1
+    #define L1_GTT_FIFO_TEST_ATOMIC 0
+    #define NEW_WKA_PATCH          0
+    #define OPTIMISED              1
+  #else
+    #define TTY_SYNC_MCU_2 0
+    #define L1_GTT_FIFO_TEST_ATOMIC 0
+    #define TTY_SYNC_MCU 0
+    #define NEW_WKA_PATCH          0
+    #define OPTIMISED              0
+
+  #endif
+ 
+  // Traces...
+  #define NUCLEUS_TRACE        0  // Nucleus error trace
+  #define FLOWCHART            0  // Message sequence/flow chart trace.
+  #define LOGFILE_TRACE        0  // trace in an output logfile
+  #define TRACE_FULL_NAME      0  // display full fct names after a PM/COM error
+
+  // Test Scenari...
+  #define SCENARIO_FILE          0  // Test Scenario comes from input files.
+  #define SCENARIO_MEM           1  //  // Test Scenario comes from RAM.
+
+  #if (OP_L1_STANDALONE == 1)
+    #define L2_L3_SIMUL            1  // Layer 2 & Layer 3 simulated, main within NU_MAIN.C, trace possible.
+  #else
+    #define L2_L3_SIMUL            0
+  #endif
+
+  // Control algorithms...
+  #define AFC_ALGO               1  // AFC algorithm.
+  //TOA Algorithm needs to be on for TestMode, otherwise no dedic test will be succesful!!!
+  #define TOA_ALGO               1  // TOA algorithm.
+  #define AGC_ALGO               1  // AGC algorithm.
+  #define TA_ALGO                1  // TA (Timing Advance) algorithm.
+
+  #define FACCH_TEST             0  // FACCH test enabled.
+
+  #define ADC_TIMER_ON           0  // Timer for ADC measurements
+  #define AFC_ON                 1  // Enable of the Omega AFC module
+
+  #define AUDIO_TASK             1  // Enable the L1 audio features
+  #define AUDIO_SIMULATION       0  // Audio simulator for the audio tasks (works only with the new audio design i.e. AUDIO_TASK=1)
+  #if (OP_L1_STANDALONE == 1)
+    #define AUDIO_L1_STANDALONE    1  // Flag to enable the audio simulator used with the L1 stand-alone (works only with the new audio design i.e. AUDIO_TASK=1)
+  #else
+    #define AUDIO_L1_STANDALONE    0
+  #endif
+
+  #define GTT_SIMULATION         0  // Gtt simulator for the gtt tasks (works only with if L1_GTT=1)
+
+  #define OP_BT                  0  // Simulation of ISLAND (BLUETOOTH) sleep management 
+
+  #define L1_RECOVERY            1  // L1 recovery
+
+
+  #if (L1_GPRS == 1)
+    #define RLC_VERSION            RLC_SCENARIO
+    #if (RLC_VERSION == RLC_SCENARIO)
+      #define RLC_DL_BLOCK_STAT    0  // Works with RLC_VERSION = RLC_SCENARIO
+                                      // output stat on CRC error blocks
+                                      // The user must enter the cs type and
+                                      // the number of frames desired.
+    #else
+      #define RLC_DL_BLOCK_STAT    0  // Default value; Never change it
+    #endif
+
+    #if (OP_L1_STANDALONE == 1)
+      #define DSP_BACKGROUND_TASKS     1 // Enable the TEST of DSP background.tasks
+                                         // activated by a layer 3 message (BG_TASK_START (<task number>))
+                                         // deactivated by a layer 3 message (BG_TASK_STOP (<task number>))
+                                         // Warning : Works only with DSP>=31
+    #else
+      #define DSP_BACKGROUND_TASKS   0
+    #endif
+
+  #else
+    #define DSP_BACKGROUND_TASKS     0
+    #define RLC_DL_BLOCK_STAT        0  // Default value; Never change it
+  #endif
+#endif
+
+// Audio tasks selection
+//-----------------------
+
+#if (AUDIO_TASK == 1)
+  #define KEYBEEP          1  // Enable keybeep feature
+  #define TONE             1  // Enable tone feature
+  // Temporary modification for protocol stack compatibility - GSMLITE will be removed
+  #if (OP_L1_STANDALONE == 1)
+    #define GSMLITE 1
+  #endif
+  #if ((OP_L1_STANDALONE == 1) || (!GSMLITE))
+    #define MELODY_E1        1  // Enable melody format E1 feature
+    #define VOICE_MEMO       1  // Enable voice memorization feature
+
+    #define FIR              1  // Enable FIR feature
+    #if (DSP == 33) || (DSP == 34) || (DSP == 35) || (DSP == 36)
+      #define AUDIO_MODE       1  // Enable Audio mode feature
+    #else
+      #define AUDIO_MODE        0  // Disable Audio mode feature
+    #endif
+  #else
+    #define MELODY_E1        0  // Disable melody format E1 feature
+    #define VOICE_MEMO       0  // Disable voice memorization feature
+    #if (MELODY_E2)
+	    #define FIR              1  // Enable FIR feature  
+	  #else
+      #define FIR              0  // Disable FIR feature  
+    #endif
+
+    #define AUDIO_MODE       0  // Disable Audio mode feature
+  #endif
+  // Define CPORT for ESample only
+  #if ((CHIPSET == 12) && ((DSP == 35) || (DSP == 36))) 
+    #define L1_CPORT         1  // Enable cport feature
+  #else
+    #define L1_CPORT         0  // Disable cport feature
+  #endif
+
+#else
+  #define KEYBEEP           0  // Enable keybeep feature
+  #define TONE              0  // Enable tone feature
+  #define MELODY_E1         0  // Enable melody format E1 feature
+  #define VOICE_MEMO        0  // Enable voice memorization feature
+
+  #define FIR               0  // Enable FIR feature
+  #define AUDIO_MODE        0  // Enable Audio mode feature
+  #define L1_CPORT          0  // Enable cport feature
+#endif
+
+#define L1_AUDIO_BACKGROUND_TASK (SPEECH_RECO | MELODY_E2) // audio background task is used by speech reco and melody_e2
+#if (OP_RIV_AUDIO == 1)
+  #define L1_AUDIO_DRIVER L1_VOICE_MEMO_AMR // Riviera audio driver (only Voice Memo AMR is available)
+#endif
+
+
+// Vocoder selections
+//-------------------
+
+#define FR        1            // Full Rate
+#define FR_HR     2            // Full Rate + Half Rate
+#define FR_EFR    3            // Full Rate + Enhanced Full Rate
+#define FR_HR_EFR 4            // Full Rate + Half Rate + Enhanced Full Rate
+
+// Standard (frequency plan) selections
+//-------------------------------------
+
+#define GSM             1            // GSM900.
+#define GSM_E           2            // GSM900 Extended.
+#define PCS1900         3            // PCS1900.
+#define DCS1800         4            // DCS1800.
+#define DUAL            5            // Dual Band (GSM900 + DCS 1800 bands)
+#define DUALEXT         6            // Dual Band (E-GSM900 + DCS 1800 bands)
+#define GSM850          7            // GSM850 Band
+#define DUAL_US         8            // PCS1900 + GSM850
+
+/*------------------------------------*/
+/* Power Management                   */
+/*------------------------------------*/
+#define PWR_MNGT  1            // POWER management active if l1_config.pwr_mngt=1
+
+
+/*---------------------------------------------------------------------------*/
+/* DSP configurations                                                        */
+/* ------------------                                                        */
+/*  DSP      | FR| HR|EFR|14.4| SPEED   |12LA68|12LA68 |4L32|AEC| MCU/DSP    */
+/* (version) |   |   |   |    |         |POLE80|POLE112|    |/NS| interface  */
+/* ----------+---+---+---+----+---------+------+-------+----+---+----------  */
+/*  0 (821)  | x |   |   |    | 39Mhz   |  x   |       |    |   | 1          */
+/* ----------+---+---+---+----+---------+------+-------+----+---+----------  */
+/*  1 (830)  | x |   |   |    | 39Mhz   | (1)  |       | x  |   | 1          */
+/* ----------+---+---+---+----+---------+------+-------+----+---+----------  */
+/*  2 (912)  | x | x |   |    | 58.5Mhz |  x   |       |    |   | 2          */
+/* ----------+---+---+---+----+---------+------+-------+----+---+----------  */
+/*  3 (10xx) | x |   | x | x  | 65Mhz   |  x   |       |    | x | 3          */
+/* ----------+---+---+---+----+---------+------+-------+----|---+----------  */
+/*  4 (11xx) | x | x | x | x  | 65Mhz   |  x   |  x (3)|    | x | 3          */
+/* ----------+---+---+---+----+---------+------+-------+----+---+----------  */
+/*  5 (830)  | x |   |   |    | 39Mhz   |  x   |       |    |   | 1          */
+/* ----------+---+---+---+----+---------+------+-------+----+---+----------  */
+/*  6 (11xx) | x | x | x | x  | 65Mhz   |  x   |  x (3)|    |(2)| 3          */
+/* ----------+---+---+---+----+---------+------+-------+----+---+----------  */
+/*                                                                           */
+/*(1) this version can be loaded on a 12LA68/POLE80 but the RIF/DL problem is*/
+/*    not corrected.                                                         */
+/*                                                                           */
+/*(2) AEC is disabled at DSP level but L1 must be compiled with MCU/DSP      */
+/*    interface which support AEC, therefore AEC is defined as 1.            */
+/*                                                                           */
+/*(3) Pole112 include RIF DL correction. No patch is needed if this one only */
+/*    include RIF/DL problem.                                                */
+/*                                                                           */
+/*---------------------------------------------------------------------------*/
+#if   (DSP == 16 || DSP == 17)
+
+/*  #define CLKMOD1    0x414e  // ...
+  #define CLKMOD2    0x414e  // ...65 Mips
+  #define CLKSTART   0x29    // ...65 Mips */
+
+  #define CLKMOD1    0x4006  // ...
+  #define CLKMOD2    0x4116  // ...65 Mips pll free
+  #define CLKSTART   0x29    // ...65 Mips
+
+/*  #define CLKMOD1     0x2116  //This settings force the DSP to never enteridle
+  #define CLKMOD2     0x2116  //In this case the PLL will be always on. 39 Mips
+  #define CLKSTART    0x25    // ...39 Mips */
+
+  #define VOC        FR_HR_EFR // FR + HR + EFR.
+  #define DATA14_4   1         // No 14.4 data allowed.
+  #define AEC        1         // AEC/NS supported.
+  #define MAP        3
+  #define DSP_START  0x2000
+  #define W_A_DSP1   0         // Work Around correcting pb in DSP: SACCH
+
+  #define W_A_DSP_SR_BGD 0    // Work around about the DSP speech reco background task.
+
+  /* DSP debug trace configuration */
+  /*-------------------------------*/
+  #if (MELODY_E2)
+    // In case of the melody E2 the DSP trace must be disable because the
+    // melody instrument waves are overlayed with DSP trace buffer
+
+    // DSP debug trace API buufer config
+    #define C_DEBUG_BUFFER_ADD  0x17ff  // Address of DSP write pointer... data are just after.
+    #define C_DEBUG_BUFFER_SIZE 7       // Real size is incremented by 1 for DSP write pointer.
+  #else
+    // DSP debug trace API buufer config
+    #define C_DEBUG_BUFFER_ADD  0x17ff  // Address of DSP write pointer... data are just after.
+    #define C_DEBUG_BUFFER_SIZE 2047    // Real size is incremented by 1 for DSP write pointer.
+  #endif
+
+#elif   (DSP == 30)    // First GPRS.
+  #define CLKMOD1    0x4006  // ...
+  #define CLKMOD2    0x4116  // ...65 Mips pll free
+  #define CLKSTART   0x29    // ...65 Mips
+
+  #define VOC        FR_HR_EFR // FR + HR + EFR.
+  #define DATA14_4   1         // No 14.4 data allowed.
+  #define AEC        1         // AEC/NS not supported.
+  #define MAP        3
+  #define DSP_START  0x1F81
+  #define W_A_DSP1   0         // Work Around correcting pb in DSP: SACCH
+  #define ULYSSE      0
+
+  #define W_A_DSP_SR_BGD 0    // Work around about the DSP speech reco background task.
+#elif   (DSP == 31)    // ROM Code GPRS G0.
+  #define CLKMOD1    0x4006  // ...
+  #define CLKMOD2    0x4116  // ...65 Mips pll free
+  #define CLKSTART   0x29    // ...65 Mips
+
+  #define VOC        FR_HR_EFR // FR + HR + EFR (normaly FR_EFR : PBs).
+  #define DATA14_4   1         // 14.4 data allowed.
+  #define AEC        1         // AEC/NS not supported.
+  #define MAP        3
+
+  #define DSP_START  0x8763
+
+  #define INSTALL_ADD            0x87c9 // Used to set gprs_install_address pointer
+  #define INSTALL_ADD_WITH_PATCH 0x1352 // Used to set gprs_install_address pointer
+
+  #define W_A_DSP1   0         // Work Around correcting pb in DSP: SACCH
+  #define ULYSSE      0
+
+  #define W_A_DSP_SR_BGD 0    // Work around about the DSP speech reco background task.
+#elif   (DSP == 32)    // ROM Code GPRS G1.
+  #define CLKMOD1    0x4006  // ...
+  #define CLKMOD2    0x4116  // ...65 Mips pll free
+  #define CLKSTART   0x29    // ...65 Mips
+
+  #define VOC        FR_HR_EFR // FR + HR + EFR (normaly FR_EFR : PBs).
+  #define DATA14_4   1         // 14.4 data allowed.
+  #define AEC        1         // AEC/NS not supported.
+  #define MAP        3
+
+  #define DSP_START  0x8763
+
+  #define INSTALL_ADD 0x87c9   // Used to set gprs_install_address pointer
+
+  #define W_A_DSP1   0         // Work Around correcting pb in DSP: SACCH
+  #define ULYSSE      0
+
+  #define W_A_DSP_SR_BGD 0    // Work around about the DSP speech reco background task.
+#elif   (DSP == 33)    // ROM Code GPRS.
+  #define CLKMOD1    0x4006  // ...
+  #define CLKMOD2    0x4116  // ...65 Mips pll free
+  #define CLKSTART   0x29    // ...65 Mips
+  #define C_PLL_CONFIG 0x154   // For VTCXO = 13 MHz and max DSP speed = 84.5 Mips
+  #define VOC        FR_HR_EFR // FR + HR + EFR (normaly FR_EFR : PBs).
+  #define AEC        1         // AEC/NS not supported.
+  #if (OP_RIV_AUDIO == 0)
+    #define L1_NEW_AEC 1
+  #else
+  // Available but not yet tuned with Riviera AUDIO    
+  #define L1_NEW_AEC 0
+  #endif
+  #if ((L1_NEW_AEC) && (!AEC))
+    // First undef the flag to avoid warnings at compilation time
+    #undef AEC
+    #define AEC 1
+  #endif
+
+  #define MAP        3
+
+  #define DSP_START  0x7000
+
+  #define INSTALL_ADD   0x7002 // Used to set gprs_install_address pointer
+
+  #define W_A_DSP1   0         // Work Around correcting pb in DSP: SACCH
+  #define ULYSSE      0
+
+  #define W_A_DSP_SR_BGD 1    // Work around about the DSP speech reco background task.
+
+  #if ( (CHIPSET != 12) && (CODE_VERSION == NOT_SIMULATION))
+
+    #define W_A_DSP_IDLE3 1     // Work around to report DSP state to the ARM for Deep Sleep
+
+                                // management.
+
+								// DSP_IDLE3 is not supported in simulation
+
+  #else
+    #define W_A_DSP_IDLE3 0
+  #endif
+
+  // DSP software work-around config
+  //  bit0 - Work-around to support CRTG.
+  //  bit1 - DMA reset on critical DMA still running cases, refer to REQ01260.
+  //  bit2 - Solve Read/Write BULDATA pointers Omega & Nausica issue, refer to BUG00650.
+  //  bit3 - Solve IBUFPTRx reset IOTA issue, refer to BUG01911.
+
+  #if    (ANALOG == 1)  // OMEGA / NAUSICA
+    #define C_DSP_SW_WORK_AROUND 0x0006
+
+  #elif  (ANALOG == 2)  // IOTA
+    #define C_DSP_SW_WORK_AROUND 0x000E
+
+  #elif  (ANALOG == 3)  // SYREN
+    #define C_DSP_SW_WORK_AROUND 0x000E
+
+  #endif
+
+  /* DSP debug trace configuration */
+  /*-------------------------------*/
+  #if (MELODY_E2)
+    // In case of the melody E2 the DSP trace must be disable because the
+    // melody instrument waves are overlayed with DSP trace buffer
+
+    // DSP debug trace API buufer config
+    #define C_DEBUG_BUFFER_ADD  0x17ff  // Address of DSP write pointer... data are just after.
+    #define C_DEBUG_BUFFER_SIZE 7       // Real size is incremented by 1 for DSP write pointer.
+
+    // DSP debug trace type config
+    //             |<-------------- Features -------------->|<---------- Levels ----------->|
+    // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR]
+    #define C_DEBUG_TRACE_TYPE  0x0000  // Level = BASIC; Features = Timer + Buffer Header + Burst.
+
+    #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4))
+      #define DSP_DEBUG_TRACE_ENABLE       1    // Enable DSP debug trace dumping capability
+                                                // Currently not supported !
+    #endif
+  #else
+    // DSP debug trace API buufer config
+    #define C_DEBUG_BUFFER_ADD  0x17ff  // Address of DSP write pointer... data are just after.
+    #define C_DEBUG_BUFFER_SIZE 2047    // Real size is incremented by 1 for DSP write pointer.
+
+    // DSP debug trace type config
+    //             |<-------------- Features -------------->|<---------- Levels ----------->|
+    // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR]
+    #define C_DEBUG_TRACE_TYPE  0x0012  // Level = BASIC; Features = Buffer Header.
+
+    #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4))
+    #define DSP_DEBUG_TRACE_ENABLE       1    // Enable DSP debug trace dumping capability (supported since patch 2090)
+    #endif
+  #endif
+  /* d_error_status                */
+  /*-------------------------------*/
+
+  #if ((TRACE_TYPE == 1) || (TRACE_TYPE == 4))
+    #define D_ERROR_STATUS_TRACE_ENABLE  1    // Enable d_error_status checking capability (supported since patch 2090)
+
+    // masks to apply on d_error_status bit field for DSP patch 0x2061 or 0x2062
+    #define DSP_DEBUG_GSM_MASK     0x0000
+    #define DSP_DEBUG_GPRS_MASK    0x0f3d
+  #endif
+
+  #if DCO_ALGO
+    // DCO type of scheduling
+    #define C_CN_DCO_PARAM 0xA248
+  #endif
+
+#elif (DSP == 34)            // ROM Code GPRS AMR.
+  #define CLKMOD1    0x4006  // ...
+  #define CLKMOD2    0x4116  // ...65 Mips pll free
+  #define CLKSTART   0x29    // ...65 Mips
+  #define C_PLL_CONFIG 0x154   // For VTCXO = 13 MHz and max DSP speed = 84.5 Mips
+  #define VOC        FR_HR_EFR // FR + HR + EFR (normaly FR_EFR : PBs).
+  #define AEC        1         // AEC/NS not supported.
+  #if (OP_RIV_AUDIO == 0)
+    #define L1_NEW_AEC 1
+  #else
+  // Available but not yet tuned with Riviera AUDIO    
+    #define L1_NEW_AEC 0
+   #endif
+  #if ((L1_NEW_AEC) && (!AEC))
+    // First undef the flag to avoid warnings at compilation time
+    #undef AEC
+    #define AEC 1
+  #endif
+  #define MAP        3
+
+  #define DSP_START  0x7000
+
+  #define INSTALL_ADD   0x7002 // Used to set gprs_install_address pointer
+
+  #define W_A_DSP1   0         // Work Around correcting pb in DSP: SACCH
+  #define ULYSSE      0
+
+  #define W_A_DSP_SR_BGD 1    // Work around about the DSP speech reco background task.
+
+  #if ( (CHIPSET != 12) && (CODE_VERSION == NOT_SIMULATION))
+
+    #define W_A_DSP_IDLE3 1     // Work around to report DSP state to the ARM for Deep Sleep
+
+                                // management.
+
+								// DSP_IDLE3 is not supported in simulation
+
+  #else
+    #define W_A_DSP_IDLE3 0
+  #endif
+
+  // DSP software work-around config
+  //  bit0 - Work-around to support CRTG.
+  //  bit1 - DMA reset on critical DMA still running cases, refer to REQ01260.
+  //  bit2 - Solve Read/Write BULDATA pointers Omega & Nausica issue, refer to BUG00650.
+  //  bit3 - Solve IBUFPTRx reset IOTA issue, refer to BUG01911.
+  #if    (ANALOG == 1)  // OMEGA / NAUSICA
+    #define C_DSP_SW_WORK_AROUND 0x0006
+
+  #elif  (ANALOG == 2)  // IOTA
+    #define C_DSP_SW_WORK_AROUND 0x000E
+
+  #elif  (ANALOG == 3)  // SYREN
+    #define C_DSP_SW_WORK_AROUND 0x000E
+
+  #endif
+
+  /* DSP debug trace configuration */
+  /*-------------------------------*/
+  #if (MELODY_E2)
+    // In case of the melody E2 the DSP trace must be disable because the
+    // melody instrument waves are overlayed with DSP trace buffer
+
+    // DSP debug trace API buufer config
+    #define C_DEBUG_BUFFER_ADD  0x17ff  // Address of DSP write pointer... data are just after.
+    #define C_DEBUG_BUFFER_SIZE 7       // Real size is incremented by 1 for DSP write pointer.
+
+    // DSP debug trace type config
+    //             |<-------------- Features -------------->|<---------- Levels ----------->|
+    // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR]
+    #define C_DEBUG_TRACE_TYPE  0x0000  // Level = BASIC; Features = Timer + Buffer Header + Burst.
+
+    #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4))
+      #define DSP_DEBUG_TRACE_ENABLE       1    // Enable DSP debug trace dumping capability
+                                                // Currently not supported !
+    #endif
+  #else
+    // DSP debug trace API buufer config
+    #define C_DEBUG_BUFFER_ADD  0x17ff  // Address of DSP write pointer... data are just after.
+    #define C_DEBUG_BUFFER_SIZE 2047    // Real size is incremented by 1 for DSP write pointer.
+
+    // DSP debug trace type config
+    //             |<-------------- Features -------------->|<---------- Levels ----------->|
+    // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR]
+    #define C_DEBUG_TRACE_TYPE  0x0012  // Level = BASIC; Features = Buffer Header.
+
+    #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4))
+    #define DSP_DEBUG_TRACE_ENABLE       1    // Enable DSP debug trace dumping capability (supported since patch 2090)
+    #endif
+
+    // AMR trace
+    #define C_AMR_TRACE_ID 55
+
+  #endif
+  /* d_error_status                */
+  /*-------------------------------*/
+
+  #if ((TRACE_TYPE == 1) || (TRACE_TYPE == 4))
+    #define D_ERROR_STATUS_TRACE_ENABLE  1    // Enable d_error_status checking capability (supported since patch 2090)
+
+    // masks to apply on d_error_status bit field
+    #define DSP_DEBUG_GSM_MASK     0x0000
+    #define DSP_DEBUG_GPRS_MASK    0x0f3d
+  #endif
+
+#elif (DSP == 35)            // ROM Code GPRS AMR.
+  #define CLKMOD1    0x4006  // ...
+  #define CLKMOD2    0x4116  // ...65 Mips pll free
+  #define CLKSTART   0x29    // ...65 Mips
+  #define C_PLL_CONFIG 0x154   // For VTCXO = 13 MHz and max DSP speed = 84.5 Mips
+  #define VOC        FR_HR_EFR // FR + HR + EFR (normaly FR_EFR : PBs).
+  #define AEC        1         // AEC/NS not supported.
+  #if (OP_RIV_AUDIO == 0)
+    #define L1_NEW_AEC 1
+  #else
+  // Available but not yet tuned with Riviera AUDIO    
+    #define L1_NEW_AEC 0
+  #endif
+  #if ((L1_NEW_AEC) && (!AEC))
+    // First undef the flag to avoid warnings at compilation time
+    #undef AEC
+    #define AEC 1
+  #endif
+  #define MAP        3
+
+  #define FF_L1_TCH_VOCODER_CONTROL 1
+  #define L1M_WAIT_DSP_RESTART_AFTER_VOCODER_ENABLE 1
+
+  #define DSP_START  0x7000
+
+  #define INSTALL_ADD   0x7002 // Used to set gprs_install_address pointer
+
+  #define W_A_DSP1   0         // Work Around correcting pb in DSP: SACCH
+  #define ULYSSE      0
+
+  #define W_A_DSP_SR_BGD 1    // Work around about the DSP speech reco background task.
+
+  #if ( (CHIPSET != 12) && (CODE_VERSION == NOT_SIMULATION))
+
+    #define W_A_DSP_IDLE3 1     // Work around to report DSP state to the ARM for Deep Sleep
+
+                                // management.
+
+								// DSP_IDLE3 is not supported in simulation
+
+  #else
+    #define W_A_DSP_IDLE3 0
+  #endif
+
+  // DSP software work-around config
+  //  bit0 - Work-around to support CRTG.
+  //  bit1 - DMA reset on critical DMA still running cases, refer to REQ01260.
+  //  bit2 - Solve Read/Write BULDATA pointers Omega & Nausica issue, refer to BUG00650.
+  //  bit3 - Solve IBUFPTRx reset IOTA issue, refer to BUG01911.
+  #if    (ANALOG == 1)  // OMEGA / NAUSICA
+    #define C_DSP_SW_WORK_AROUND 0x0006
+
+  #elif  (ANALOG == 2)  // IOTA
+    #define C_DSP_SW_WORK_AROUND 0x000E
+
+  #elif  (ANALOG == 3)  // SYREN
+    #define C_DSP_SW_WORK_AROUND 0x000E
+
+  #endif
+
+  /* DSP debug trace configuration */
+  /*-------------------------------*/
+  #if (MELODY_E2)
+    // In case of the melody E2 the DSP trace must be disable because the
+    // melody instrument waves are overlayed with DSP trace buffer
+
+    // DSP debug trace API buufer config
+    #define C_DEBUG_BUFFER_ADD  0x17ff  // Address of DSP write pointer... data are just after.
+    #define C_DEBUG_BUFFER_SIZE 7       // Real size is incremented by 1 for DSP write pointer.
+
+    // DSP debug trace type config
+    //             |<-------------- Features -------------->|<---------- Levels ----------->|
+    // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR]
+    #define C_DEBUG_TRACE_TYPE  0x0000  // Level = BASIC; Features = Timer + Buffer Header + Burst.
+
+    #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4))
+      #define DSP_DEBUG_TRACE_ENABLE       1    // Enable DSP debug trace dumping capability
+                                                // Currently not supported !
+    #endif
+  #else
+    // DSP debug trace API buufer config
+    #define C_DEBUG_BUFFER_ADD  0x17ff  // Address of DSP write pointer... data are just after.
+    #define C_DEBUG_BUFFER_SIZE 2047    // Real size is incremented by 1 for DSP write pointer.
+
+    // DSP debug trace type config
+    //             |<-------------- Features -------------->|<---------- Levels ----------->|
+    // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR]
+    #define C_DEBUG_TRACE_TYPE  0x0012  // Level = BASIC; Features = Timer + Buffer Header + Burst.
+
+    #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4))
+    #define DSP_DEBUG_TRACE_ENABLE       1    // Enable DSP debug trace dumping capability (supported since patch 2090)
+    #endif
+
+    // AMR trace
+    #define C_AMR_TRACE_ID 55
+
+  #endif
+  /* d_error_status                */
+  /*-------------------------------*/
+
+  #if ((TRACE_TYPE == 1) || (TRACE_TYPE == 4))
+    #define D_ERROR_STATUS_TRACE_ENABLE  1    // Enable d_error_status checking capability (supported since patch 2090)
+
+    // masks to apply on d_error_status bit field for DSP patch 0x2061 or 0x2062
+    #define DSP_DEBUG_GSM_MASK     0x08BD
+    #define DSP_DEBUG_GPRS_MASK    0x0f3d
+  #endif
+#elif (DSP == 36)            // ROM Code GPRS AMR.
+  #define CLKMOD1    0x4006  // ...
+  #define CLKMOD2    0x4116  // ...65 Mips pll free
+  #define CLKSTART   0x29    // ...65 Mips
+  #define C_PLL_CONFIG 0x154   // For VTCXO = 13 MHz and max DSP speed = 84.5 Mips
+  #define VOC        FR_HR_EFR // FR + HR + EFR (normaly FR_EFR : PBs).
+  #define AEC        1         // AEC/NS not supported.
+  #if (OP_RIV_AUDIO == 0)
+    #define L1_NEW_AEC 1
+  #else
+  // Available but not yet tuned with Riviera AUDIO    
+    #define L1_NEW_AEC 0
+  #endif
+  #if ((L1_NEW_AEC) && (!AEC))
+    // First undef the flag to avoid warnings at compilation time
+    #undef AEC
+    #define AEC 1
+  #endif
+  #define MAP        3
+  #undef  L1_AMR_NSYNC
+  #define L1_AMR_NSYNC 1
+  #define FF_L1_TCH_VOCODER_CONTROL 1
+  #define L1M_WAIT_DSP_RESTART_AFTER_VOCODER_ENABLE 1
+
+  #define DSP_START  0x7000
+
+  #define INSTALL_ADD   0x7002 // Used to set gprs_install_address pointer
+
+  #define W_A_DSP1   0         // Work Around correcting pb in DSP: SACCH
+  #define ULYSSE      0
+
+  #define W_A_DSP_SR_BGD 1    // Work around about the DSP speech reco background task.
+
+  #if ( (CHIPSET != 12) && (CODE_VERSION == NOT_SIMULATION))
+
+    #define W_A_DSP_IDLE3 1     // Work around to report DSP state to the ARM for Deep Sleep
+
+                                // management.
+
+								// DSP_IDLE3 is not supported in simulation
+
+  #else
+    #define W_A_DSP_IDLE3 0
+  #endif
+
+  // DSP software work-around config
+  //  bit0 - Work-around to support CRTG.
+  //  bit1 - DMA reset on critical DMA still running cases, refer to REQ01260.
+  //  bit2 - Solve Read/Write BULDATA pointers Omega & Nausica issue, refer to BUG00650.
+  //  bit3 - Solve IBUFPTRx reset IOTA issue, refer to BUG01911.
+  #if    (ANALOG == 1)  // OMEGA / NAUSICA
+    #define C_DSP_SW_WORK_AROUND 0x0006
+
+  #elif  (ANALOG == 2)  // IOTA
+    #define C_DSP_SW_WORK_AROUND 0x000E
+
+  #elif  (ANALOG == 3)  // SYREN
+    #define C_DSP_SW_WORK_AROUND 0x000E
+  #endif
+
+  // This workaround should be enabled only for H2-sample on full build config
+  #if (OP_L1_STANDALONE==1)
+    #define RAZ_VULSWITCH_REGAUDIO 0
+  #endif
+
+  /* DSP debug trace configuration */
+  /*-------------------------------*/
+  #if (MELODY_E2)
+    // In case of the melody E2 the DSP trace must be disable because the
+    // melody instrument waves are overlayed with DSP trace buffer
+
+    // DSP debug trace API buufer config
+    #define C_DEBUG_BUFFER_ADD  0x17ff  // Address of DSP write pointer... data are just after.
+    #define C_DEBUG_BUFFER_SIZE 7       // Real size is incremented by 1 for DSP write pointer.
+
+    // DSP debug trace type config
+    //             |<-------------- Features -------------->|<---------- Levels ----------->|
+    // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR]
+    #define C_DEBUG_TRACE_TYPE  0x0000  // Level = BASIC; Features = Timer + Buffer Header + Burst.
+
+    #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4))
+      #define DSP_DEBUG_TRACE_ENABLE       1    // Enable DSP debug trace dumping capability
+                                                // Currently not supported !
+    #endif
+  #else
+    // DSP debug trace API buufer config
+    #define C_DEBUG_BUFFER_ADD  0x17ff  // Address of DSP write pointer... data are just after.
+    #define C_DEBUG_BUFFER_SIZE 2047    // Real size is incremented by 1 for DSP write pointer.
+
+    // DSP debug trace type config
+    //             |<-------------- Features -------------->|<---------- Levels ----------->|
+    // [15-8:UNUSED|7:TIMER|6:BURST|5:BUFFER|4:BUFFER HEADER|3:UNUSED|2:KERNEL|1:BASIC|0:ISR]
+    #define C_DEBUG_TRACE_TYPE  0x0012  // Level = BASIC; Features = Buffer Header.
+
+    #if (C_DEBUG_TRACE_TYPE != 0) && ((TRACE_TYPE == 1) || (TRACE_TYPE == 4))
+    #define DSP_DEBUG_TRACE_ENABLE       1    // Enable DSP debug trace dumping capability (supported since patch 2090)
+    #endif
+
+    // AMR trace
+    #define C_AMR_TRACE_ID 55
+
+  #endif
+  /* d_error_status                */
+  /*-------------------------------*/
+
+  #if ((TRACE_TYPE == 1) || (TRACE_TYPE == 4))
+    #define D_ERROR_STATUS_TRACE_ENABLE  1    // Enable d_error_status checking capability (supported since patch 2090)
+
+    // masks to apply on d_error_status bit field for DSP patch 0x2061 or 0x2062
+    #define DSP_DEBUG_GSM_MASK     0x08BD
+    #define DSP_DEBUG_GPRS_MASK    0x0f3d
+  #endif
+#endif // DSP
+
+/*------------------------------------*/
+/* Default value                      */
+/*------------------------------------*/
+#ifndef W_A_DSP1
+  #define W_A_DSP1   0
+#endif
+
+#ifndef DATA14_4
+  #define DATA14_4   0
+#endif
+
+#ifndef W_A_ITFORCE
+  #define W_A_ITFORCE   0
+#endif
+
+#ifndef W_A_DSP_IDLE3
+  #define W_A_DSP_IDLE3 0
+#endif
+
+#ifndef L1_NEW_AEC
+  #define L1_NEW_AEC 0
+#endif
+
+#ifndef DSP_DEBUG_TRACE_ENABLE
+  #define DSP_DEBUG_TRACE_ENABLE 0
+#endif
+
+#ifndef DEBUG_DEDIC_TCH_BLOCK_STAT
+  #define DEBUG_DEDIC_TCH_BLOCK_STAT 0
+#endif
+
+#ifndef D_ERROR_STATUS_TRACE_ENABLE
+  #define D_ERROR_STATUS_TRACE_ENABLE  0
+#endif
+
+#ifndef L1_GTT
+  #define L1_GTT 0
+  #define TTY_SYNC_MCU 0
+  #define TTY_SYNC_MCU_2 0
+  #define L1_GTT_FIFO_TEST_ATOMIC 0
+  #define NEW_WKA_PATCH          0
+  #define OPTIMISED              0
+#endif
+
+#ifndef L1_AMR_NSYNC
+  #define L1_AMR_NSYNC 0
+#endif
+
+#ifndef FF_L1_TCH_VOCODER_CONTROL
+  #define FF_L1_TCH_VOCODER_CONTROL 0
+  #define L1M_WAIT_DSP_RESTART_AFTER_VOCODER_ENABLE 0 
+#endif
+
+/*------------------------------------*/
+/* Download                           */
+/*------------------------------------*/
+
+
+/* Possible values for the download status */
+
+#define LEAD_READY      1
+#define BLOCK_READY     2
+#define PROGRAM_DONE    3
+#define PAGE_SELECTION  4
+
+
+/************************************/
+/* Options of compilation...        */
+/************************************/
+
+// Possible choice of hardware plateform.
+#define GEMINI       1   // GEMINI chip (rom dsp code)
+#define POLESTAR     2   // POLESTAR chip (no rom)
+
+// Possible choice for DSP software setup.
+#define NO_DWNLD         0
+#define PATCH_DWNLD      1
+#define DSP_DWNLD        2
+#define PATCH_DSP_DWNLD  3
+
+// MAC-S status reporting to Layer 1
+#define MACS_STATUS     0   // MAC-S STATUS activated if set to 1
+
+
+// Possible choice for dll_dcch_downlink interface (with FN or without FN)
+#define SEND_FN_TO_L2_IN_DCCH 1 /* 0=without, 1=with FN parameter */
+
+//---------------------------------------------------------------------------------
+
+// Neighbor Cell RXLEV indication
+#if ((OP_L1_STANDALONE==1) && (CODE_VERSION == NOT_SIMULATION))
+ #define  L1_MPHC_RXLEV_IND_REPORT_SORT 1
+#else
+ #define  L1_MPHC_RXLEV_IND_REPORT_SORT 0
+#endif
+
+#endif /* __L1_CONFG_H__ */