FreeCalypso > hg > freecalypso-sw
changeset 583:ff1065828669
tpudrv12.c: l1dmacro_init_hw() done
| author | Michael Spacefalcon <msokolov@ivan.Harhan.ORG> |
|---|---|
| date | Fri, 15 Aug 2014 21:49:39 +0000 |
| parents | 81753f5e902e |
| children | d42078e35ac9 |
| files | gsm-fw/L1/tpudrv/tpudrv12.c |
| diffstat | 1 files changed, 5 insertions(+), 87 deletions(-) [+] |
line wrap: on
line diff
--- a/gsm-fw/L1/tpudrv/tpudrv12.c Fri Aug 15 19:25:58 2014 +0000 +++ b/gsm-fw/L1/tpudrv/tpudrv12.c Fri Aug 15 21:49:39 2014 +0000 @@ -842,7 +842,7 @@ // Set FEM to inactive state before turning ON the RF Board // At this point the RF regulators are still OFF. Thus the // FEM command is not inverted yet => Must use the FEM "SLEEP programming" - + *TP_Ptr++ = TPU_MOVE(TSP_ACT, 0x01); // TPU_SLEEP l1dmacro_idle(); @@ -850,10 +850,10 @@ *TP_Ptr++ = TPU_AT(t); *TP_Ptr++ = TPU_SYNC(0); - //Check Initialisation or Reset for TPU2OCP - - - *TP_Ptr++ = TPU_MOVE(REG_SPI_ACT_U, TXM_SLEEP); + /* from disassembly, differs from LoCosto version */ + *TP_Ptr++ = TPU_MOVE(TSP_SPI_SET1, 0x20); + *TP_Ptr++ = TPU_MOVE(TSP_SPI_SET2, 0x06); + *TP_Ptr++ = TPU_MOVE(TSP_SPI_SET3, 0x00); t = 1000; // arbitrary start time @@ -887,85 +887,3 @@ return; } - -//BHO added -/* - * l1dmacro_rx_fbsb - * - * Receive Frequency burst - */ - -#if ((REL99 == 1) && (FF_BHO == 1)) -#if(L1_RF_KBD_FIX == 1) -#if (L1_MADC_ON == 1) -void l1dmacro_rx_fbsb (SYS_UWORD16 radio_freq, UWORD8 adc_active) -#else -void l1dmacro_rx_fbsb (SYS_UWORD16 radio_freq) -#endif -{ -#if (L1_MADC_ON == 1) - l1dmacro_rx_up(adc_active, L1_SAIC_HARDWARE_FILTER, L1_KBD_DIS_RX_FB - #if(NEW_SNR_THRESHOLD==1) - , SAIC_OFF - #endif - ); -#else - l1dmacro_rx_up(L1_SAIC_HARDWARE_FILTER, L1_KBD_DIS_RX_FB); -#endif - - - // same as rx_fb - *TP_Ptr++ = TPU_AT(0); // 1 - *TP_Ptr++ = TPU_AT(0); // 2 - *TP_Ptr++ = TPU_AT(0); // 3 - *TP_Ptr++ = TPU_AT(0); // 4 - *TP_Ptr++ = TPU_AT(0); // 5 - *TP_Ptr++ = TPU_AT(0); // 6 - *TP_Ptr++ = TPU_AT(0); // 7 - *TP_Ptr++ = TPU_AT(0); // 8 - *TP_Ptr++ = TPU_AT(0); // 9 - *TP_Ptr++ = TPU_AT(0); // 10 - *TP_Ptr++ = TPU_AT(0); // 11 - - // one more for SB - *TP_Ptr++ = TPU_AT(0); // 12 - - l1dmacro_rx_down (STOP_RX_FBSB); -} -#endif/*(L1_RF_KBD_FIX == 1)*/ - -#if(L1_RF_KBD_FIX == 0) -#if (L1_MADC_ON == 1) -void l1dmacro_rx_fbsb (SYS_UWORD16 radio_freq, UWORD8 adc_active) -#else -void l1dmacro_rx_fbsb (SYS_UWORD16 radio_freq) -#endif -{ -#if (L1_MADC_ON == 1) - l1dmacro_rx_up(adc_active, L1_SAIC_HARDWARE_FILTER); -#else - l1dmacro_rx_up(L1_SAIC_HARDWARE_FILTER); -#endif - - // same as rx_fb - *TP_Ptr++ = TPU_AT(0); // 1 - *TP_Ptr++ = TPU_AT(0); // 2 - *TP_Ptr++ = TPU_AT(0); // 3 - *TP_Ptr++ = TPU_AT(0); // 4 - *TP_Ptr++ = TPU_AT(0); // 5 - *TP_Ptr++ = TPU_AT(0); // 6 - *TP_Ptr++ = TPU_AT(0); // 7 - *TP_Ptr++ = TPU_AT(0); // 8 - *TP_Ptr++ = TPU_AT(0); // 9 - *TP_Ptr++ = TPU_AT(0); // 10 - *TP_Ptr++ = TPU_AT(0); // 11 - - // one more for SB - *TP_Ptr++ = TPU_AT(0); // 12 - - l1dmacro_rx_down (STOP_RX_FBSB); -} -#endif/*(L1_RF_KBD_FIX == 0)*/ -#endif // #if ((REL99 == 1) && (FF_BHO == 1)) - -////BHO