FreeCalypso > hg > freecalypso-tools
annotate loadtools/README.older @ 416:30f6d1c32c6f
doc/Flash-boot-defect article removed (no longer relevant)
This article is no longer relevant because the issue in question
only affected one (1) defective FCDEV3B board which was not
and never will be sold.
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Fri, 26 Oct 2018 07:11:08 +0000 |
parents | d5d6992897cf |
children |
rev | line source |
---|---|
0
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
1 You are looking at the source for the FreeCalypso loadtools package. You may |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
2 have downloaded it either as a separate package or as part of the larger |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
3 freecalypso-sw suite. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
4 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
5 The tools in this package are written to run on some Unix/Linux machine |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
6 (normally a PC/Linux desktop or laptop) that acts as a host for operating on |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
7 Calypso target devices. All of these tools communicate with the Calypso target |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
8 through a serial port; each tool begins its operation by sending special byte |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
9 sequences to this serial port which are designed to interrupt the Calypso |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
10 device boot process in the ROM bootloader. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
11 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
12 Three utilities are currently built as part of FreeCalypso loadtools: |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
13 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
14 fc-iram & fc-xram These utilities are intended for FreeCalypso developers |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
15 only. They load an S-record code image into IRAM or |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
16 XRAM, respectively, induce a transfer of control to the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
17 loaded code, and then drop into a serial line pass-thru |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
18 mode for the operator to interact with the thus loaded |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
19 target code. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
20 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
21 fc-loadtool This utility is intended for both developers and end |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
22 users. After establishing communication with the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
23 target, fc-loadtool drops into interactive operation. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
24 Once at the loadtool> prompt, you can peek and poke |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
25 registers, and most importantly, dump (read) and load |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
26 (program) the flash memory of the target device. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
27 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
28 Loadagent |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
29 ========= |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
30 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
31 Both fc-loadtool and fc-xram work by first feeding a FreeCalypso-developed |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
32 program called loadagent to the Calypso ROM bootloader; all further operations |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
33 (loading code into XRAM or flash) are done via this loadagent. An S-record |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
34 image of the loadagent program is required for fc-loadtool and fc-xram to work. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
35 That program is in turn built with the ARM7 toolchain. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
36 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
37 If you are working with the full freecalypso-sw suite, you presumably already |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
38 have the proper ARM7 toolchain built and installed. To build loadagent, simply |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
39 run 'make' in the ../target-utils tree. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
40 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
41 If you have downloaded a separately-packaged version of FreeCalypso loadtools, |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
42 the package should have a prebuilt loadagent.srec image included, sparing |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
43 non-developer users the nontrivial hurdle of having to build and install a |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
44 special cross-compilation toolchain. The same loadagent binary is designed to |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
45 work on all supported Calypso targets. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
46 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
47 Building and installing loadtools |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
48 ================================= |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
49 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
50 Normally the machine on which you build and install fc-loadtools would be your |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
51 PC/Linux desktop or laptop, the system you would use to program or otherwise |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
52 interact with Calypso phones by way of appropriate USB-to-phone cables. Just |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
53 like loadagent, the host utilities you are going to build and install aren't |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
54 specific to a particular target device; instead you will select the target |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
55 device at run time via a command line option. Hence you can build and install |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
56 the host utilities (usual 'make' and 'make install') without limiting your |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
57 setup to just one target phone type. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
58 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
59 However, if your intended target device is an Openmoko GTA02 (or GTA01) |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
60 smartphone, there is one additional complication: one cannot directly access |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
61 the Calypso part of these phones from the outside without going through the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
62 phone's application processor first. If you would like to use fc-loadtool to |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
63 read or write the GSM flash memory of your GTA0x (load a different firmware |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
64 image, dump the flash file system for backup or examination, restore a previous |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
65 backup etc), there are two ways to do it: |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
66 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
67 1. The recommended way for FreeCalypso developers is to get a special serial |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
68 cable (low voltage, as in 3.3V or lower - *NOT* RS-232 levels - please don't |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
69 fry your precious phone!) that would plug into the 2.5mm jack on the left |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
70 side of the phone that is normally intended for a wired headset. This way |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
71 you can use your regular build of fc-loadtool (and fc-iram & fc-xram) on |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
72 your PC/Linux (or other) development host, no need to build anything for |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
73 GTA0x AP, and all communication happens directly between your development |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
74 host and the Calypso part of your target phone - not going through the AP |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
75 at all. You still need working software on the GTA0x AP to do battery |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
76 management, to power the Calypso block on and off, and to enable the headset |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
77 jack "download" path, but it is much less burdensome than having to do the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
78 actual FreeCalypso work from the AP. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
79 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
80 Having the headset jack do double duty as a programming port is actually a |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
81 standard practice in the world of basic (non-smart) cellular phones, and |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
82 furthermore, the pinout used by FIC on the GTA0x phones just happens to be |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
83 exactly the same as that used by Compal/Motorola - hence the same headset jack |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
84 serial cables that are used by OsmocomBB with the latter phones (the famous |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
85 "T191 unlock cable") will also work for connecting from an external host |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
86 directly to the Calypso part of GTA0x phones. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
87 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
88 2. If you are an end user who simply wishes to reflash a different GSM firmware |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
89 image, it can be done from inside the phone (from the AP) without having to |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
90 acquire special hardware (as in the cable described above). However, the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
91 trade-off is that in return for saving on the special hardware, you have to |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
92 do more work on the software. You will have to use a cross-compiler |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
93 targeting the ARM/Linux AP environment (*not* the ARM7 cross-compiler used |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
94 for the GSM firmware itself!) to build fc-loadtools to run on the GTA0x AP. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
95 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
96 Building loadtools for GTA0x AP |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
97 =============================== |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
98 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
99 If you've decided to build loadtools for the GTA0x AP, you'll need to make the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
100 following modifications to the Makefile: |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
101 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
102 * Change the CC= line to point to the appropriate cross-compiler (which you'll |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
103 need to provide yourself); |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
104 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
105 * Change the CFLAGS= line: add the right options to target the ARM920T core in |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
106 the GTA0x AP (e.g., -march=armv4t -mtune=arm920t), and add -DGTA0x_AP_BUILD |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
107 to enable some code that makes sense only when running on the GTA0x AP. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
108 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
109 * Change EXTRA_OBJ= to EXTRA_OBJ=gtapower.o, i.e., add gtapower.c (compiling |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
110 into gtapower.o) to the build. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
111 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
112 See gta-ap-build.sed for an example. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
113 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
114 Running fc-loadtool |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
115 =================== |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
116 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
117 Once you've got loadtools built and installed, you can run fc-loadtool |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
118 as follows: |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
119 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
120 To operate on a Pirelli DP-L10 that appears as /dev/ttyUSB0: |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
121 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
122 fc-loadtool -h pirelli /dev/ttyUSB0 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
123 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
124 The usb2serial chip inside the phone is bus-powered and will be visible as |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
125 /dev/ttyUSBx whether the phone battery is present or not. There are two ways |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
126 to break into the bootloader: |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
127 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
128 1. Run the fc-loadtool command given above with the USB cable connected, but no |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
129 battery present. Once loadtool says "Sending beacons to <port>", insert the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
130 battery. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
131 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
132 2. Connect the USB cable to a powered-on phone running its original factory |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
133 firmware. (If the phone was off, it will power up and boot in the "charging |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
134 only" mode - it is not possible for a Calypso/Iota phone to be completely |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
135 off when both the battery and the charging voltage are present.) Run |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
136 fc-loadtool as above - it will start sending its beacons, which will be |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
137 ignored by the running fw. Then execute the "power off" operation from the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
138 UI (unlock the keypad, then press and hold the red button). The presence of |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
139 USB VBUS (used as the charging power source on this phone) will turn the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
140 power-off into a reboot, and you'll break into the bootloader. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
141 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
142 To operate on the Calypso block of a GTA02, accessing it from an external |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
143 PC/Linux host via a USB-to-headset-jack serial cable that appears as |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
144 /dev/ttyUSB0: |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
145 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
146 fc-loadtool -h gta02 /dev/ttyUSB0 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
147 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
148 Run the above command first, then power on the GSM modem from the AP - or power |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
149 it off, then on if it was on already. The "download" path needs to be enabled |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
150 (controlled from the AP) and fc-loadtool needs to be running on the external |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
151 host when the modem is powered on. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
152 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
153 To operate on the Calypso block of a GTA02, running fc-loadtool from inside the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
154 phone, i.e., from the AP of the same GTA02: |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
155 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
156 fc-loadtool -h gta02 /dev/ttySAC0 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
157 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
158 In this last scenario the specially built version of fc-loadtool running on the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
159 AP takes care of manipulating the modem power to induce entry into the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
160 bootloader, thus no extra manual steps are needed. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
161 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
162 See loadtool.help for a detailed description of the functionality and commands |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
163 that are available once loadtool is running and communicating with loadagent on |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
164 the target device. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
165 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
166 Command line options |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
167 ==================== |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
168 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
169 The fc-loadtool command lines shown above will usually be sufficient. However, |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
170 here is the complete command line description for all 3 tools: |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
171 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
172 fc-iram [options] ttyport iramimage.srec |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
173 fc-xram [options] ttyport xramimage.srec [2ndprog] |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
174 fc-loadtool [options] ttyport |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
175 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
176 The available options are common for all 3 utilities, with a few noted |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
177 exceptions: |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
178 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
179 -a /path/to/loadagent |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
180 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
181 This option applies only to fc-loadtool and fc-xram. It specifies the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
182 pathname at which the required loadagent.srec image should be sought, |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
183 overriding the compiled-in default. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
184 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
185 -b baud |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
186 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
187 This option is common for all 3 utilities. It selects the baud rate |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
188 to be used when pushing the IRAM image to the Calypso boot ROM. In the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
189 case of fc-iram, the selected baud rate will be in effect when the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
190 loaded IRAM image is jumped to and fc-iram drops into the serial tty |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
191 pass-thru mode; in the case of fc-loadtool, it will be the initial baud |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
192 rate for communicating with loadagent, which can be switched later with |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
193 the baud command. The default is 115200 baud. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
194 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
195 -B baud |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
196 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
197 This option is specific to fc-xram. It selects the baud rate to be |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
198 used when pushing the XRAM image to loadagent. If no -B option is |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
199 specified, fc-xram will communicate with loadagent at the same baud |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
200 rate that was used to load loadagent itself via the Calypso boot ROM |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
201 download protocol, i.e., the rate selected with -b, defaulting to |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
202 115200 baud if no -b option was given either. Neither -b nor -B |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
203 affects the baud rate that will be in effect when the loaded XRAM image |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
204 is jumped to and fc-xram drops into the serial tty pass-thru mode: that |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
205 baud rate independently defaults to 115200 baud and can only be changed |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
206 with the -r option. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
207 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
208 -h hwtype |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
209 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
210 This option is common for all 3 utilities. It selects the specific |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
211 target device configuration to be used. More precisely, it constructs |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
212 a pathname of the form /usr/local/share/freecalypso/%s.config, where %s |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
213 is the argument given to this option, and uses that file as the hardware |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
214 parameters file. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
215 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
216 The hardware configurations known to the present release of FreeCalypso |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
217 loadtools are gta02 and pirelli. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
218 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
219 -H /path/to/hwparam-file |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
220 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
221 This option is just like -h, except that the given argument is used |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
222 directly as the hardware parameter file pathname (absolute or relative) |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
223 without alteration. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
224 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
225 -i num |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
226 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
227 This option is common for all 3 utilities. It specifies the interval |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
228 in milliseconds at which the tool will send "please interrupt the boot |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
229 process" beacons out the serial port, hoping to catch the Calypso |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
230 internal boot ROM. The default is 13 ms. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
231 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
232 -n |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
233 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
234 This option does anything only when loadtools have been compiled to run |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
235 on GTA0x AP. If you've compiled loadtools with the -DGTA0x_AP_BUILD |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
236 option, it has an effect of making each tool automatically toggle the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
237 modem power control upon startup, removing the need for manual |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
238 sequencing of the Calypso boot process. This -n option suppresses that |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
239 action, making the AP build behave like the standard build in this |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
240 regard. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
241 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
242 -r baud |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
243 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
244 This option is specific to fc-xram. It selects the serial line baud |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
245 rate which should be set just before the loaded XRAM image is jumped |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
246 to; the default is 115200 baud. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
247 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
248 fc-xram 2nd program invokation |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
249 ============================== |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
250 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
251 The fc-xram utility can take two possible actions after it has loaded the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
252 specified S-record image into XRAM: |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
253 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
254 * The default action, in the absence of additional command line arguments, is |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
255 to drop into a serial tty pass-thru mode, just like fc-iram. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
256 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
257 * The alternative action is to invoke a 2nd program and pass the serial |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
258 communication channel to it. This 2nd program invokation facility is intended |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
259 primarily for passing the serial communication channel to rvinterf or rvtdump |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
260 from the FreeCalypso software suite, not for launching any arbitrary 3rd-party |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
261 programs from fc-xram. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
262 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
263 The intended usage scenario is that one builds a version of the FreeCalypso GSM |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
264 firmware (or some subset thereof, such as an "in vivo" FFS editing agent) in the |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
265 ramImage configuration, fc-xram is used to load that ramImage into the target |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
266 device, and then the serial communication channel (RVTMUX) is immediately taken |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
267 over by rvinterf or rvtdump. |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
268 |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
269 More detailed usage instructions will be written when the rvinterf tools reach |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
270 a point of being usable by more than just the original developer; until then, |
e7502631a0f9
initial import from freecalypso-sw rev 1033:5ab737ac3ad7
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff
changeset
|
271 read the source code. |