FreeCalypso > hg > freecalypso-tools
view doc/RVTMUX @ 102:3431a069254f
target-utils: c139explore converted to our own libc
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Tue, 01 Nov 2016 00:20:14 +0000 |
parents | d9307880f59f |
children | ac49d8814893 |
line wrap: on
line source
TI's Calypso GSM/GPRS baseband processor chip has not one but two UART serial ports, called "MODEM" and "IrDA" in the hardware documentation. In hardware terms, both support basic data-leads-only UART operation at a fixed baud rate, but their extended capabilities differ: the IrDA UART adds IrDA capability (no surprise), whereas the MODEM UART adds hardware flow control and autobaud. If one is not implementing an actual IrDA interface, then the so-called "IrDA" UART becomes a strict subset of the MODEM one in terms of hw capabilities - just an extra UART, but a somewhat less capable one. In a classic modem design such as that present in the GTA0x smartphones made by FIC/Openmoko, the Calypso presents a standard AT command interface on its MODEM UART port. (In the case of GTA0x phones this serial channel is wired to the phone's application processor; in a standalone modem it would be wired to a USB-serial chip or even to a classic RS-232 DB25 port.) However, what is less known is that the standard firmware for such modems simultaneously presents an entirely different interface on the IrDA UART - an interface intended for development, debugging and factory production testing (which includes RF calibration and IMEI etc programming), rather than for "normal" end users. Normally this debug/development serial interface (called RVTMUX as will be explained momentarily) is hidden from "ordinary" users - for example, on FIC GTA0x phones it is wired to the analog headset jack through a hardware switch which needs to be enabled through a GPIO signal from the AP. On Mot C139 and its siblings the situation is similar: one needs to key in the secret magic sequence **16379#, and then the firmware presents a hidden menu for switching the analog headset jack between its "normal" function and the UART carrying RVTMUX. But there also exist some oddball devices on which the RVTMUX interface is presented "in your face". The Pirelli DP-L10 phone has a USB charging port which is also wired (through a CP2102 USB-serial chip) to the IrDA UART on the Calypso - that's right, IrDA, not MODEM - a design decision with which this hacker strongly disagrees. (It'll definitely be wired to the MODEM UART instead on our own semi-clone of this phone, but I digress.) Apparently Foxconn (the designers of this phone) had no desire to provide a standard AT command interface, and instead the only "official" way to use the "data" function of their USB port (rather than the charging function) is for their "PC sync" feature, i.e., their proprietary Weendoze software. And guess what, their proprietary "PC sync" feature works over TI's RVTMUX interface, as that is what's presented on Calypso's IrDA UART behind the CP2102! OK, so what is this RVTMUX? RV stands for RiViera, an application framework which TI added to their GSM firmware suite in the early 2000s, T stands for trace, and MUX stands for multiplexor. It's a binary packet interface, although many of these packets contain ASCII debug messages inside. The framing format is the same in both directions: each packet begins and ends with an STX (0x02) byte, all payload bytes except 0x02 and 0x10 are sent literally, and there is a DLE (0x10) byte prepended before any 0x02 or 0x10 in the payload. It's the same general principle as asynchronous HDLC (RFC 1662): packets can contain any binary data, and the framing provides packet boundaries - although TI's version is a little less robust than async-HDLC when it comes to recovering after lost synchronization. The firmware suite component responsible for actually sending and receiving these packets over the assigned UART port (usually IrDA, but can be MODEM too, as on Compal phones for example) is called RVT (RiViera Trace), and it implements a MUX function. There are several logical channels multiplexed over one physical serial port, and the first byte of every packet indicates which logical channel it belongs to. Any component within the GSM firmware suite can send packets to RVT for transmission on this serial interface, and can also register to receive packets beginning with a particular type ID byte. Debug trace output ================== All GSM device firmwares that are based on TI's Calypso chipset reference fw continuously emit quite voluminous debug trace output on their RVTMUX serial port, whether it is hidden or exposed on a given device. Like all RVTMUX traffic, this debug trace output takes the form of binary packets as explained above, but the content of these packets is mostly ASCII with some binary header bytes prepended. FreeCalypso host utility rvtdump captures all serial output from a GSM device's RVTMUX port, parses the packet structure and displays this output in line-oriented pure ASCII with all binary parts decoded. Test Mode commands ================== The other major use of the RVTMUX interface is sending so-called Test Mode commands from an external host to a running GSM device. Depending on the firmware version, a GSM device can be commanded to do any of the following things through this mechanism: * Exercise RF test modes, e.g., transmit continuously at a set frequency and power level; * Read and write arbitrary memory locations in the Calypso ARM7 address space; * Read and write ABB chip registers; * Reboot or power off; * Access and manipulate the device's flash file system (FFS). In the segment of history of interest to us TI has produced two different target firmware components that can receive, interpret and act upon Test Mode command packets: * The original Test Mode component of Layer 1, called L1TM or TML1: this component handles all RF test modes (needed for RF calibration on device production lines), and originally it also implemented memory and ABB register read and write commands, and provided access to TMFFS1 (see below). In the original implementation this component registered itself as the handler for the "TM" RVTMUX channel (RVT packet type 0x14), so it would receive all TM packets sent to the device. * Enhanced Test Mode (ETM) is a later invention. It registers itself (instead of the old TM in L1) with RVT as the handler for the "TM" RVTMUX channel, and then provides a registration service of its own, such that various components in the fw suite can register to receive external command packets passing first through RVT, then through ETM, and can send responses passing through ETM, then through RVT back to the external host. If a given fw version contains both ETM and L1TM, then L1TM registers itself with ETM; an external host would send exactly the same binary command packets to exercise RF test modes, but inside the firmware they now pass through ETM on their way to L1TM. The ETM_CORE module contained within ETM itself provides some low-level debug commands: by sending the right binary command packets to the GSM device via the RVTMUX serial channel, an external host can examine or modify any memory location and any hardware register, cause the device to reset, etc. Prior to ETM some of these functions (but not all) could be exercised through older TM3 commands, but in FreeCalypso we became familiar with the ETM versions of these commands long before the older ones because we got the ETM component in full source form, whereas our copy of TCS211 (TI's reference fw) has L1TM in a binary library. Our TCS211/leo2moko reference fw has both ETM and L1TM, thus it accepts both ETM and TM3 command packets. ETM commands (including TMFFS2, see below) work on Pirelli's fw, but Mot/Compal's original fw for the C139 has only the original non-enhanced Test Mode, not ETM. FFS access via TM/ETM ===================== One of the essential facilities provided in one form or another in all known incarnations of the Test Mode mechanism is the ability to access and manipulate the GSM device's flash file system (FFS). See TIFFS-Overview for a description of this file system. TI's TMFFS1 and TMFFS2 protocols provide a command and response packet interface to the FFS API functions inside the fw, and enable an external host connected to the GSM device via the RVTMUX channel to perform arbitrary read and write operations on the device file system. In the segment of history of interest to us TI has produced two different and entirely incompatible versions of the TMFFS protocol: TMFFS1 and TMFFS2. Or rather, what is now called TMFFS1 was originally just TMFFS, and then came TMFFS2. TMFFS2 works only through ETM, whereas TMFFS1 predates ETM: in the original implementation the tm_ffs() function in the FFS code was called from L1TM code. Our copy of TCS211 reference fw includes the source for both TMFFS1 and TMFFS2; it is theoretically possible to build a firmware image that includes both TMFFS versions (they won't conflict because they respond to different command packets), but it is pretty clear that TI never intended to have both enabled at the same time. Our copy of TCS211 came with TMFFS1 enabled and we didn't change it when we made the moko12 (leo2moko-r1) fw release for the Openmoko community (the previous proprietary mokoN firmwares also implement TMFFS1), but we have subsequently switched to TMFFS2 for our current TCS211-based work. Pirelli's fw implements TMFFS2: we don't have any source for this fw, but our FreeCalypso host utilities written to talk the TMFFS2 protocol based on our available TCS211 source work beautifully when run against Pirelli's fw. Use in FreeCalypso ================== The FreeCalypso project has adopted the same general firmware architecture as that exhibited by TI's standard firmwares from the Moko/Pirelli time frame. We use TI's RiViera framework lifted directly out of the TCS211 reference fw, and that includes the RVT module and the RVTMUX interface it presents. Our GSM fw emits the same 3 kinds of debug traces (RV, L1 and GPF) as the pre-existing firmwares with which we are seeking functional parity, and for Test Mode functionality we have the option of including ETM, TMFFS1 and/or TMFFS2 in our firmware builds. (Both TMFFS versions require ETM in our implementation, and it is possible to build a firmware image with both included.) We have adopted ETM and TMFFS2 as the standard combination for FreeCalypso, i.e., ETM_CORE for memory and ABB register reads and writes and TMFFS2 for external FFS access. We needed to develop our own host tools for operating on GSM device FFS via one of the two TMFFS protocols, and after studying the fw source implementing both, I (Space Falcon) came to the conclusion that TMFFS2 is both more capable and more reliable; my guess is that TMFFS1 was likely kept around only because some of TI's crappy Weendoze host software depended on it. (See chipsetsw/drivers/drv_app/ffs/board/tmffs.c in leo2moko or tcs211-fcmodem if you would like to judge for yourself.) We have the following host tools for communicating with TI-based GSM firmwares (both our own and some of the existing proprietary ones): rvtdump This tool produces a human-readable dump of all output emitted by a TI-based GSM fw in the form of RVTMUX binary packets. It can also log this dump to a file. rvinterf This tool is a superset of rvtdump: it not only dumps and/or logs all output from the GSM fw, but also provides a mechanism for sending command packets to it. Rvinterf is the engine behind the following host tools that send Test Mode commands to a target: fc-tmsh This is our basic tool for sending Test Mode commands to a running GSM fw. It is strictly asynchronous in that commands entered by the operator get sent to the target, and any response packets received from the target are displayed as they come in. The tool has no knowledge of any correspondence between commands being sent and whatever responses they should elicit, i.e., it is perfectly suited for experimental discovery of firmware behaviour in response to Test Mode commands. This tool was written before we realized that there was/is an older, more basic Test Mode predating ETM, hence in many place we say "ETM" when we really should have said "TM". Oh well... fc-fsio This tool speaks the TMFFS2 protocol and allows a user or developer to perform a wide range of operations on the file system of a GSM device. It operates synchronously, i.e., it sends ETM/TMFFS2 commands and expects responses in strict lock-step; a single user command may translate into a large number of ETM/TMFFS2 command packet exchanges. AT commands over RVTMUX ======================= There is one more use to which we put the RVTMUX debug serial interface that is an original FreeCalypso invention: communicating with the AT command interpreter (ATI). TI's original architecture assumes that if a product is to offer a standard AT command interface (the product is either a GSM/GPRS modem for which this AT command interface is the sole mode of usage or a feature phone that offers a data port as one of its features), then it will be presented on a dedicated UART separate from RVTMUX. However, many of our target devices have only one UART practically accessible, and even when we use Openmoko's modem as our development platform, the RVTMUX interface is more convenient because it connects externally, whereas the MODEM UART is connected to the application processor of the smartphone. Therefore, we developed a way to pass AT commands over RVTMUX. We created a new RVTMUX channel for this interface and assigned it RVT packet type 0x1A. Packets sent from an external host to the GSM device carry AT commands and SMS string input, whereas packets flowing the other way carry ATI's responses to commands and asynchronous notifications such as incoming calls. The host utility for talking AT commands to a FreeCalypso GSM device via RVTMUX is fc-shell; it works via rvinterf just like fc-fsio and fc-tmsh.