annotate doc/Sniffer-FPGA-design @ 4:b275c69c1b80

doc: describe proposed FPGA design
author Mychaela Falconia <falcon@freecalypso.org>
date Sat, 29 Jul 2023 07:06:54 +0000
parents
children 41e6026e5d1a
Ignore whitespace changes - Everywhere: Within whitespace: At end of lines:
rev   line source
4
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
1 The first FPGA gateware function to be implemented in the SIMtrace-ice project
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
2 is the passive sniffer: receiving level-shifted SIM RST, CLK and I/O signals
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
3 from the 74LVC4T3144 buffer and capturing all exchanges that happen on the SIM
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
4 interface between a DUS and a SIM.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
5
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
6 The sniffer FPGA logic function will be implemented on the inexpensive off-the-
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
7 shelf Icestick board, featuring an iCE40HX1K FPGA and an FT2232H-based USB host
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
8 interface. This FPGA logic function will operate principally as a byte
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
9 forwarder from the ISO 7816-3 sniffer block to the FT2232H UART: every time the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
10 bus sniffer block captures a character (in ISO 7816-3 terminology) being passed
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
11 on the SIM electrical interface in either direction (the two directions of
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
12 transmission are indistinguishable to a tap sniffer that does not actively
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
13 participate in the protocol), the FPGA will forward this character to the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
14 connected host computer (by way of FT2232H UART) for further processing in
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
15 software. The UART data line going from the FPGA to the FT2232H will be the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
16 sole functional output from this FPGA, beyond debug outputs being added during
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
17 logic development and troubleshooting. The other UART data line going the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
18 opposite direction (output from FT2232H) will remain unused, i.e., the host
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
19 software application will only read/receive from the ttyUSBx FPGA device and
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
20 won't send anything to it. All modem control lines on this UART interface will
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
21 likewise remain unused.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
22
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
23 Serial interface format
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
24 =======================
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
25
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
26 For every ISO 7816-3 character captured by the sniffer, two back-to-back UART
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
27 bytes will be transferred from the FPGA to the host computer; more generally,
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
28 the FPGA will only transmit pairs of back-to-back bytes on this UART and no
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
29 singletons or other arrangements - thus the host receiver can always recover
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
30 synchronization by dropping any partially received two-byte message (the first
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
31 byte of an expected pair) during prolonged pauses. The FPGA will transmit the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
32 two back-to-back UART bytes as a single shift-out of 20 bits, conveying two
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
33 bytes in 8N1 framing.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
34
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
35 Why are we turning every captured ISO 7816-3 character into a pair of bytes on
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
36 our internal UART interface, why not simply forward it as a single byte? The
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
37 reason is that we need to pass some additional bits beyond the 8 that comprise
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
38 the ISO 7816-3 character payload; the additional bits which we need to pass are
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
39 as follows:
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
40
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
41 - the received parity bit;
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
42 - a flag indicating whether or not an error signal (ISO 7816-3 section 7.3)
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
43 was seen;
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
44 - additional flag bits communicating SIM RST assertion and negation events,
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
45 as distinct from ISO 7816-3 characters;
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
46 - an additional flag indicating an action of the integrated PPS catcher state
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
47 machine, to be described later in this document.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
48
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
49 Assertion or negation of SIM RST is the only other possible event (besides ISO
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
50 7816-3 character capture, with or without attendant PPS catcher state machine
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
51 action) that can cause the FPGA to send a byte-pair UART message to the host
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
52 computer. One bit in the 16-bit message will distinguish between characters
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
53 and RST events, another bit will indicate the state of RST at the time of the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
54 event (new RST for transitions, 1 for characters), and all other bits are
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
55 meaningful only for characters.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
56
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
57 Clocking design
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
58 ===============
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
59
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
60 The FPGA on the Icestick board receives a 12 MHz clock input; the on-chip PLL
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
61 will be used to multiply this clock by 4, producing a 48 MHz system clock.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
62 This 48 MHz SYSCLK will be used for the entirety of the present logic design -
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
63 a single-clock fully synchronous design is the best current practice.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
64
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
65 The 3 inputs to the FPGA coming from the SIM electrical sniffer (buffered and
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
66 level-shifted SIM RST, CLK and I/O lines) will pass through two cascaded DFFs,
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
67 bringing them into our internal clock domain. The delay added by these cascaded
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
68 DFFs is not a concern: we are a passive sniffer without any output back to the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
69 SIM interface, and all 3 signal inputs will be subject to the same delay.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
70
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
71 The baud rate on the UART interface between the FPGA and the FT2232H converter
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
72 will be 3000000 bps. The UART output block in the FPGA will use a simple /16
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
73 divider from SYSCLK to time its output bits; future derivative designs that will
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
74 use the UART interface bidirectionally (such as the planned card emulator FPGA
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
75 design) will use SYSCLK directly as the 16x clock for UART reception. This
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
76 high (and very non-RS232-standard) UART baud rate was chosen for the following
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
77 reasons:
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
78
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
79 * Our UART interface is totally private, going nowhere but the on-board FT2232H,
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
80 thus it doesn't matter if the baud rate is standard-ish or totally
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
81 non-standard.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
82
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
83 * No cables of any kind are used, instead the UART interface is confined to
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
84 short PCB traces running between the FPGA and the FTDI chip on the same board
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
85 - hence high baud rates are not a problem.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
86
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
87 * Our UART baud rate needs to be high enough to provide good margin, despite
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
88 our 2x expansion, at the highest possible effective bps rate on the SIM
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
89 interface, meaning the highest possible SIM CLK frequency and the most
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
90 aggressive F/D ratio. The combination of SIM CLK at 5 MHz, F=512 and D=64
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
91 corresponds to 625000 bps effective on the SIM interface; running our UART at
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
92 3 Mbps provides sufficient margin.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
93
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
94 ISO 7816-3 sniffer block
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
95 ========================
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
96
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
97 Our ISO 7816-3 receiver will trigger on the falling edge of the I/O line. Once
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
98 it detects a high-to-low transition on the SYSCLK-synchronized SIM_IO input, it
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
99 will start counting SIM CLK cycles - we are arbitrarily choosing low-to-high
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
100 transition of SYSCLK-synchronized SIM_CLK input as the trigger point. (This
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
101 choice is arbitrary because per the spec there is no defined phase relation
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
102 between SIM CLK and SIM I/O transitions.) Our ISO 7816-3 receiver will need to
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
103 know how many SIM CLK cycles constitute one etu - or more precisely, our
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
104 sniffing receiver will operate in half-etu counts, as we need to measure 0.5 etu
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
105 to get from the initial falling edge on the I/O line to the mid-etu data
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
106 sampling point. Following the session-opening low-to-high transition on the RST
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
107 line, our half-etu register will be set to 8'd186, corresponding to F/D=372.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
108 Our PPS catcher state machine will then overwrite this register with a smaller
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
109 value based on the captured PPS exchange.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
110
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
111 Direct and inverse coding conventions
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
112 =====================================
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
113
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
114 Only the card and not the DUS (interface device in ISO 7816-3 terminology)
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
115 determines which coding convention is used, direct or inverse. So far we
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
116 (FreeCalypso) have not yet encountered a real-life SIM that uses the inverse
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
117 convention, only the direct convention kind. In the sniffer function of
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
118 SIMtrace-ice, we are going to keep our FPGA gateware simple in this regard and
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
119 punt all inverse convention handling to the software application on the host
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
120 computer: the FPGA will pass the 9 received bits (8 data bits and 1 parity bit)
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
121 to the 16-bit UART message as-is, without inverting or reordering them.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
122
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
123 Integrated PPS catcher
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
124 ======================
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
125
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
126 The logic described so far will be sufficient to capture all exchanges on the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
127 SIM interface between a DUS and a SIM *if* the etu-defining F/D ratio is never
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
128 switched from the basic default of 372. However, given that most SIM cards of
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
129 interest to us (our own FCSIM1, as well as SIMs issued by various commercial
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
130 operators) support Fi=512 Di=8 or higher, and given that even very classic
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
131 implementations of GSM ME (including our dear Calypso) support this F=512 D=8
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
132 speed enhancement mode endorsed by GSM 11.11 spec, many real-life DUS-to-SIM
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
133 sessions (which we would like to sniff and trace) will include a PPS exchange
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
134 switching to a smaller number of SIM CLK cycles per etu.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
135
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
136 The main difficulty with capturing SIM interface sessions that use speed
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
137 enhancement is as follows: in order for the session capture to be complete,
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
138 without any lost bits, the sniffing receiver's knowledge of how many SIM CLK
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
139 cycles constitute a half-etu needs to change to the new value at exactly the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
140 correct moment in time, which is the moment immediately after the last byte
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
141 (PCK) of the SIM's PPS response passes across the wire. If we were to rely on
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
142 host software to decode all byte exchanges up to this point (ATR from the SIM,
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
143 PPS request from the DUS, then PPS response) and command the FPGA (UART in the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
144 other direction, or a modem control line) to switch the half-etu counter, we
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
145 stand very little chance of getting this command to the FPGA in time, before
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
146 the DUS starts transmitting its next command to the SIM using the new etu
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
147 definition.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
148
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
149 The Mother's proposed solution is to embed a PPS catcher state machine in the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
150 sniffer FPGA. This state machine will be set to its initial state upon the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
151 session-opening low-to-high transition on the RST line, and it will look at
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
152 every ISO 7816-3 character received by the sniffer. The machine will need to
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
153 step through the following states between this starting point and the final
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
154 action of changing the half-etu count register:
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
155
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
156 * As the ATR bytes are transferred, the state machine will need to understand
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
157 enough of ATR format to know which byte constitutes the end of ATR. A fatal
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
158 error in ATR real-time parsing (if the first byte is anything other than
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
159 8'h3B) will put the machine into its inactive state for the remainder of the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
160 session until next reset.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
161
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
162 * If the byte following ATR is 8'hFF, the machine will proceed into PPS request
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
163 real-time parsing state. If this byte equals any other value, go to the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
164 inactive state for the remainder of the session.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
165
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
166 * In the PPS request real-time parsing series of states, the state machine will
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
167 need to catch the PPS0 byte and based on this byte, figure out how many bytes
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
168 it needs to skip.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
169
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
170 * Following the PPS request, the machine will need to real-time-parse the PPS
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
171 response. Any invalid conditions will take it to the inactive state; however,
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
172 if the PPS exchange is valid, the machine will need to capture the PPS1 byte
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
173 and then step through states until the final PCK byte of the PPS response.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
174
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
175 * Upon receiving that last PCK byte after all prior bytes following the expected
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
176 protocol, effect the half-etu count change. Either way, the inactive state
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
177 is entered at this point, and the state machine will take no further action
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
178 for the remainder of the session.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
179
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
180 This state machine is of course going to be very complicated, as evident from
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
181 the functional requirements listed above. The first version of SIMtrace-ice
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
182 sniffer FPGA will omit this block altogether, and we will get the rest of the
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
183 system working for DUS-to-SIM sessions that stick with F/D=372 - a good test
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
184 configuration would be to use a FreeCalypso GSM ME as DUS, with SIM speed
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
185 enhancement disabled via AT@SPENH=0. Then we shall embark on implementing this
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
186 proposed PPS catcher state machine.
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
187
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
188 The addition of this PPS catcher state machine may increase the complexity of
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
189 our logic beyond the capacity of the iCE40HX1K FPGA on the Icestick board. If
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
190 we run into this problem, we'll have to look for a board with a bigger FPGA -
b275c69c1b80 doc: describe proposed FPGA design
Mychaela Falconia <falcon@freecalypso.org>
parents:
diff changeset
191 but we'll try to fit into the Icestick first.