FreeCalypso > hg > freecalypso-citrine

comparison L1/tpudrv/tpudrv8.h @ 0:75a11d740a02

Find changesets by keywords (author, files, the commit message), revision number or hash, or revset expression.
initial import of gsm-fw from freecalypso-sw rev 1033:5ab737ac3ad7
author Mychaela Falconia <falcon@freecalypso.org>
date Thu, 09 Jun 2016 00:02:41 +0000
parents
children
comparison
equal deleted inserted replaced
-1:000000000000 0:75a11d740a02
1 /****************** Revision Controle System Header ***********************
2 * GSM Layer 1 software
3 * Copyright (c) Texas Instruments 1998
4 *
5 * Filename tpudrv8.h
6 * Copyright 2003 (C) Texas Instruments
7 *
8 ****************** Revision Controle System Header ***********************/
9
10 //SI4133 definitions
11 #define WordAdd0000 0x000000 //Main Configuration
12 #define AutoPDB 0x000080 //Auto Power Down - Uses PWDNB pin
13 #define AuxSel 0x030000 //Auxiliary output pin use = LOCK Detect
14 #define WordAdd0011 0x000003 //RF1 N Divider
15 #define WordAdd0100 0x000004 //RF2 N Divider
16 #define WordAdd0101 0x000005 //IF N Divider
17 #define RFPWR 0x000020 //RF LO high power
18 #define XPDM 0x000100 //Reference amplifier ON when PWDNB pin = 0
19
20 //TRF6053 definitions
21 #define Mode0 0x000000
22 #define Mode1 0x000001
23 #define Mode2 0x000003
24 #define Mode3 0x000005
25 #define Mode4 0x000007
26 #define LNAMixPwrOn 0x000080 //Mode0
27 #define VCODiv2PwrOn 0x000040 //Mode0
28 #define RXBBIFStgPwrOn 0x000020 //Mode0
29 #define OFFStrCalOn 0x000010 //Mode0
30 #define VCORDivPwrOn 0x000008 //Mode0
31 #define MixLOBuffPwrOn 0x000004 //Mode0
32 #define TXStagesPwrOn 0x000002 //Mode0
33 #define FreqDetDis 0x000400 //Mode4
34 #define IFVCOExternal 0x000200 //Mode4
35 #define IFPLLBuffDis 0x000100 //Mode4
36 #define LBandLNAExt 0x000080 //Mode4
37 #define HBandLNAExt 0x000040 //Mode4
38 #define Div2ToRXStgs 0x000020 //Mode4
39 #define DivRToTXStgs 0x000010 //Mode4
40 #define ChgPPLBNeg 0x000010 //Mode2
41 #define ChgPPHBNeg 0x000010 //Mode3
42 #define PreCCLBDis 0x000008 //Mode2
43 #define PreCCHBDis 0x000008 //Mode3
44 #define LNAGainLow 0x000010 //Mode2
45 #define BandHigh 0x000008 //Mode1
46 #define LowBIF610 0x000020 //Mode2
47 #define HighBIF412 0x000020 //Mode3
48 #define HighBIF25 0x000040 //Mode3
49 #define HighBIF410 0x000060 //Mode3
50
51 /*------------------------------------------*/
52 /* Download delay values */
53 /*------------------------------------------*/
54 #define TRF6053_DOWNLOAD_TIME 15
55 #define SYNTH_DOWNLOAD_TIME 20
56
57 //--------------------------------------------
58 // internal tpu timing
59 //--------------------------------------------
60
61 #define DLT_1 1 // 1 tpu instruction = 1 qbit
62 #define DLT_2 2
63 #define DLT_3 3
64 #define DLT_4 4
65
66 #define DLT_1B 4 // 3*move + 1*byte (download)
67 #define DLT_2B 6 // 4*move + 2*byte
68 #define DLT_3B 8 // 5*move + 3*byte
69
70 #define SL_SU_DELAY1 4 // No. bits to send + load data to shift + send write cmd + 1
71 #define SL_SU_DELAY2 3 // load data to shift + send write cmd + 1
72 #define SL_SU_DELAY3 5 // SL_SU_DELAY1 + serialization
73
74 /*------------------------------------------*/
75 /* Download delay values */
76 /*------------------------------------------*/
77 // 0.9230769 usec ~ 1 qbit i.e. 200 usec is ~ 217 qbit
78
79 #define T TPU_CLOCK_RANGE // TODO: should be a define from L1.
80
81 // time below are offset to when BDLENA goes low
82 #define TRF_R11 ( 0 - DLT_1B) // disable BDLON & BDLENA
83 #define TRF_R10 ( - 5 - DLT_1B) // disable TRF6053
84
85 // burst data comes here
86 // time below are offset to when BDLENA goes high
87 #define TRF_R9 (PROVISION_TIME - 0 - DLT_1B) // enable BDLENA, disable BDLCAL
88 #define TRF_R8 (PROVISION_TIME - 11 - DLT_1B) // power on RX front end, DC cal. off
89 #define TRF_R7 (PROVISION_TIME - 65 - DLT_1B) // enable BDLCAL
90 #define TRF_R6 (PROVISION_TIME - 72 - DLT_1B) // enable BDLON
91 #define TRF_R5 (PROVISION_TIME - 76 - DLT_1B) // power on receiver, start DC cal.
92 #define TRF_R4 (PROVISION_TIME - 80 - DLT_2B) // set RX gain & band.
93 // ADC read, uses min 11 qbit due to 5 wait
94 #define TRF_R3 (PROVISION_TIME - 196 - DLT_1B) // power up TRF2253
95 #define TRF_R1 (PROVISION_TIME - 205 - DLT_3B) // set RF PLL N counter = r1 and IF PLL N counter in TRF2253 = r2
96
97 // time below are offset to when BULENA goes low
98 #define TRF_T13 ( 32 - DLT_1B) // disable PA_ON, BULON, TRF6053
99 #define TRF_T12 ( 18 - DLT_1 ) // disable TSPACT01
100 #define TRF_T11 ( 0 - DLT_1B) // disable BULENA
101 #define TRF_T10_1 (- 40 - DLT_1B) // ADC read
102 // burst data comes here
103 // time below are offset to when BULENA goes high
104 #define TRF_T10 (+ 15 - DLT_3) // enable PA_ON + 2*rfswitch
105 #define TRF_T9 (- 0 - DLT_1B) // enable BULENA
106 #define TRF_T8 (- 109 - DLT_2B) // power on transceiver
107 #define TRF_T7 (- 115 - DLT_1B) // disable BULCAL
108 #define TRF_T6 (- 230 - DLT_1B) // power up TRF2253
109 #define TRF_T5 (- 233 - DLT_2B) // set TX band in TRF6053
110 #define TRF_T3 (- 249 - DLT_3B) // set RF PLL N counter = t3 and IF PLL N counter in TRF2253 = t4
111 #define TRF_T2 (- 260 - DLT_1B) // enable BULCAL
112 #define TRF_T1 (- 278 - DLT_1B) // enable BULON
113
114 #if (BOARD == 7) || (BOARD == 8) || (BOARD == 9) || (BOARD == 40) || (BOARD == 41) || (BOARD == 42) || (BOARD == 43) || (BOARD == 45)
115 #define PA_ON 0x20 // act5
116 #define TSPACT01 0x02 // act1
117
118 // RF signals connected to TSPACTX
119 #define RX900 0x04 // act10
120 #define RX1800 0x08 // act11
121
122 #define TC1_DEVICE_ABB TC1_DEVICE0
123 #define TC1_DEVICE_RF TC1_DEVICE1
124 #define TC1_DEVICE_PLL TC1_DEVICE2
125 #endif
126
127 #if (BOARD == 6)
128 #define PA_ON 0x10 // act4
129
130 // RF signals connected to TSPACTX
131 #define RX900 0x08 // act11 => needs to be connected to act12
132 #define RX1800 0x04 // act10
133
134 #define TC1_DEVICE_ABB TC1_DEVICE0
135 #define TC1_DEVICE_PLL TC1_DEVICE1
136 #define TC1_DEVICE_RF TC1_DEVICE2
137 #endif
138
139 #ifdef TPUDRV8_C
140 // Function prototypes
141 SYS_UWORD16 Convert_l1_radio_freq(SYS_UWORD16 radio_freq);
142
143 #endif