FreeCalypso > hg > freecalypso-citrine
diff L1/tpudrv/tpudrv8.h @ 0:75a11d740a02
initial import of gsm-fw from freecalypso-sw rev 1033:5ab737ac3ad7
| author | Mychaela Falconia <falcon@freecalypso.org> |
|---|---|
| date | Thu, 09 Jun 2016 00:02:41 +0000 |
| parents | |
| children |
line wrap: on
line diff
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/L1/tpudrv/tpudrv8.h Thu Jun 09 00:02:41 2016 +0000 @@ -0,0 +1,143 @@ +/****************** Revision Controle System Header *********************** + * GSM Layer 1 software + * Copyright (c) Texas Instruments 1998 + * + * Filename tpudrv8.h + * Copyright 2003 (C) Texas Instruments + * + ****************** Revision Controle System Header ***********************/ + +//SI4133 definitions +#define WordAdd0000 0x000000 //Main Configuration +#define AutoPDB 0x000080 //Auto Power Down - Uses PWDNB pin +#define AuxSel 0x030000 //Auxiliary output pin use = LOCK Detect +#define WordAdd0011 0x000003 //RF1 N Divider +#define WordAdd0100 0x000004 //RF2 N Divider +#define WordAdd0101 0x000005 //IF N Divider +#define RFPWR 0x000020 //RF LO high power +#define XPDM 0x000100 //Reference amplifier ON when PWDNB pin = 0 + +//TRF6053 definitions +#define Mode0 0x000000 +#define Mode1 0x000001 +#define Mode2 0x000003 +#define Mode3 0x000005 +#define Mode4 0x000007 +#define LNAMixPwrOn 0x000080 //Mode0 +#define VCODiv2PwrOn 0x000040 //Mode0 +#define RXBBIFStgPwrOn 0x000020 //Mode0 +#define OFFStrCalOn 0x000010 //Mode0 +#define VCORDivPwrOn 0x000008 //Mode0 +#define MixLOBuffPwrOn 0x000004 //Mode0 +#define TXStagesPwrOn 0x000002 //Mode0 +#define FreqDetDis 0x000400 //Mode4 +#define IFVCOExternal 0x000200 //Mode4 +#define IFPLLBuffDis 0x000100 //Mode4 +#define LBandLNAExt 0x000080 //Mode4 +#define HBandLNAExt 0x000040 //Mode4 +#define Div2ToRXStgs 0x000020 //Mode4 +#define DivRToTXStgs 0x000010 //Mode4 +#define ChgPPLBNeg 0x000010 //Mode2 +#define ChgPPHBNeg 0x000010 //Mode3 +#define PreCCLBDis 0x000008 //Mode2 +#define PreCCHBDis 0x000008 //Mode3 +#define LNAGainLow 0x000010 //Mode2 +#define BandHigh 0x000008 //Mode1 +#define LowBIF610 0x000020 //Mode2 +#define HighBIF412 0x000020 //Mode3 +#define HighBIF25 0x000040 //Mode3 +#define HighBIF410 0x000060 //Mode3 + +/*------------------------------------------*/ +/* Download delay values */ +/*------------------------------------------*/ +#define TRF6053_DOWNLOAD_TIME 15 +#define SYNTH_DOWNLOAD_TIME 20 + +//-------------------------------------------- +// internal tpu timing +//-------------------------------------------- + +#define DLT_1 1 // 1 tpu instruction = 1 qbit +#define DLT_2 2 +#define DLT_3 3 +#define DLT_4 4 + +#define DLT_1B 4 // 3*move + 1*byte (download) +#define DLT_2B 6 // 4*move + 2*byte +#define DLT_3B 8 // 5*move + 3*byte + +#define SL_SU_DELAY1 4 // No. bits to send + load data to shift + send write cmd + 1 +#define SL_SU_DELAY2 3 // load data to shift + send write cmd + 1 +#define SL_SU_DELAY3 5 // SL_SU_DELAY1 + serialization + +/*------------------------------------------*/ +/* Download delay values */ +/*------------------------------------------*/ +// 0.9230769 usec ~ 1 qbit i.e. 200 usec is ~ 217 qbit + +#define T TPU_CLOCK_RANGE // TODO: should be a define from L1. + +// time below are offset to when BDLENA goes low +#define TRF_R11 ( 0 - DLT_1B) // disable BDLON & BDLENA +#define TRF_R10 ( - 5 - DLT_1B) // disable TRF6053 + +// burst data comes here +// time below are offset to when BDLENA goes high +#define TRF_R9 (PROVISION_TIME - 0 - DLT_1B) // enable BDLENA, disable BDLCAL +#define TRF_R8 (PROVISION_TIME - 11 - DLT_1B) // power on RX front end, DC cal. off +#define TRF_R7 (PROVISION_TIME - 65 - DLT_1B) // enable BDLCAL +#define TRF_R6 (PROVISION_TIME - 72 - DLT_1B) // enable BDLON +#define TRF_R5 (PROVISION_TIME - 76 - DLT_1B) // power on receiver, start DC cal. +#define TRF_R4 (PROVISION_TIME - 80 - DLT_2B) // set RX gain & band. + // ADC read, uses min 11 qbit due to 5 wait +#define TRF_R3 (PROVISION_TIME - 196 - DLT_1B) // power up TRF2253 +#define TRF_R1 (PROVISION_TIME - 205 - DLT_3B) // set RF PLL N counter = r1 and IF PLL N counter in TRF2253 = r2 + +// time below are offset to when BULENA goes low +#define TRF_T13 ( 32 - DLT_1B) // disable PA_ON, BULON, TRF6053 +#define TRF_T12 ( 18 - DLT_1 ) // disable TSPACT01 +#define TRF_T11 ( 0 - DLT_1B) // disable BULENA +#define TRF_T10_1 (- 40 - DLT_1B) // ADC read +// burst data comes here +// time below are offset to when BULENA goes high +#define TRF_T10 (+ 15 - DLT_3) // enable PA_ON + 2*rfswitch +#define TRF_T9 (- 0 - DLT_1B) // enable BULENA +#define TRF_T8 (- 109 - DLT_2B) // power on transceiver +#define TRF_T7 (- 115 - DLT_1B) // disable BULCAL +#define TRF_T6 (- 230 - DLT_1B) // power up TRF2253 +#define TRF_T5 (- 233 - DLT_2B) // set TX band in TRF6053 +#define TRF_T3 (- 249 - DLT_3B) // set RF PLL N counter = t3 and IF PLL N counter in TRF2253 = t4 +#define TRF_T2 (- 260 - DLT_1B) // enable BULCAL +#define TRF_T1 (- 278 - DLT_1B) // enable BULON + +#if (BOARD == 7) || (BOARD == 8) || (BOARD == 9) || (BOARD == 40) || (BOARD == 41) || (BOARD == 42) || (BOARD == 43) || (BOARD == 45) + #define PA_ON 0x20 // act5 + #define TSPACT01 0x02 // act1 + + // RF signals connected to TSPACTX + #define RX900 0x04 // act10 + #define RX1800 0x08 // act11 + + #define TC1_DEVICE_ABB TC1_DEVICE0 + #define TC1_DEVICE_RF TC1_DEVICE1 + #define TC1_DEVICE_PLL TC1_DEVICE2 +#endif + +#if (BOARD == 6) + #define PA_ON 0x10 // act4 + + // RF signals connected to TSPACTX + #define RX900 0x08 // act11 => needs to be connected to act12 + #define RX1800 0x04 // act10 + + #define TC1_DEVICE_ABB TC1_DEVICE0 + #define TC1_DEVICE_PLL TC1_DEVICE1 + #define TC1_DEVICE_RF TC1_DEVICE2 +#endif + +#ifdef TPUDRV8_C +// Function prototypes +SYS_UWORD16 Convert_l1_radio_freq(SYS_UWORD16 radio_freq); + +#endif